Reddit mentions: The best nut inserts
We found 21 Reddit comments discussing the best nut inserts. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 10 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. uxcell M3x5mm(L)-5mm(OD) Metric Threaded Brass Knurl Round Insert Nuts 100pcs
- [M3 Metric] - Thread Diameter: M3; Pitch: 0.5mm; Outer Dia: 5.2mm; Length: 5mm.
- [Material] - Made of brass material, high hardness and durable. Provides good mechanical properties with increased corrosion and heat resistance
- [Feature] - It can be installed into a plastic matrix by ultrasound or heat during the injection molding process.
- [Easy to Install] - The knurled insert nut has a guide, so no countersink is required. The surface is smooth, firm and even, and easy to install.
- [Application] - Can be widely used in 3D printing injection molding to achieve tight fixation.
Features:
Specs:
Height | 16 Inches |
Length | 0 Inches |
Number of items | 100 |
Weight | 0.25 Pounds |
Width | 16 Inches |
2. SNUG Fasteners (SNG870) Ten (10) #8-32 Brass Knife Threaded Inserts for Wood | .375" Length
Superior hard wood holding power with knife thread#8-32 Internal thread and .375" lengthSolid brassEasily installs with a screwdriver, bolt/jam nut, or optional drive toolUse with 17/64ā drill bit
Specs:
Height | 0.5 Inches |
Length | 4 Inches |
Number of items | 10 |
Width | 6 Inches |
3. uxcell a16041800ux0824 M3 x 3 mm Female Thread Brass Knurled Threaded Insert Embedment Nuts 100PCS (Pack of 100)
- Thread Size: M3 / 0.12"; Product Name: Knurled Nut
- Material: Brass; Weight: 14g
- Package Content: 100(+/-2%) x Knurled Nuts; Main Color: Brass Tone
- Pitch: 0.5mm; Outer Diameter: 4.1mm / 0.16"
- Length: 3mm / 0.12"
Features:
Specs:
Number of items | 100 |
Release date | August 2018 |
4. Uxcell Furniture Cam Fitting with Dowel and Pre-inserted Nut, 5-Pack
- Cam Fittings Size : Overall Size(Approx): 0.56inch x 0.433inch(DH)
- Inner Hole Height(Approx): 3.5mm / 0.138inch : Inner Hole Height(Approx): 3.5mm / 0.138inch;Dowel Size : Male Thread Dia: 5.6mm / 0.220inch
- Overall Length: 1.56inch : Overall Length:1.56inch;Pre-inserted Nut Size : 0.19inch x 0.42inch x 0.41inch(Inner DODH)
- Material : Metal Cam Fittings & Dowel , Plastic Pre-inserted Nut;Color : Silver Tone, White
- Net Weight : 53g;Package Content : 5 Sets of Furniture Connecting Fittings
Features:
Specs:
Color | "Silver Tone, White" |
Height | 0.43 Inches |
Length | 0.55 Inches |
Number of items | 1 |
Width | 0.43 Inches |
5. Glarks 370Pcs M2 M3 M4 M5 Female Thread Knurled Brass Threaded Insert Embedment Nut Assortment Kit for 3D Printing
- ā Product Type: High quality knurled thread inserts nuts assortment kit.
- ā Package Detail: In this set, it include 15 kinds of m2, m3, m4, m5 knurl thread inserts nuts total 370pcs which are well packed in a plastic box.
- ā Product Material: All the nuts are made of premium brass, which has high hardness, no deformation, durable and reliable for long time use.
- ā Easy to install: Since the insert has a conduction valve, there is no need to back-drill and counter-sink the hole.
- ā Product Feature: Widely used on the injection moulding for tightly fixing; can be installed by ultrasonic or heat into thread tapered hole, or molded in during injection.
Features:
Specs:
Number of items | 370 |
6. uxcell 20pcs M4x8mm Threaded Insert Nuts Zinc Alloy Hex Socket M4 Internal Threads 8mm Length
- Internal Thread Size: M4; Nut External Diameter: 8mm/0.31"; Length: 8mm/0.31"; Applicable Drill Size: 6mm/0.24"
- Material: Zinc alloy material, color zinc finish, oxidation resistance, good toughness, corrosion resistance.
- Application: Suitable for connection and fastening of various objects, often used in furniture cabinets, wardrobes, and connecting plates. Good effect on furniture combination.
- Design: Inner hex head with flange, trapezoidal design, evenly stressed on the inner and outer teeth, and the structure is more stable. The flange has a positioning function and is installed on the surface of the connecting surface.
- Installation: Make a hole with the corresponding bit size, and lock the nut with a hexagonal wrench. The mounting hole should not be larger than the outer diameter of the thread. When the nut is locked, some wood glue can be applied to the outer teeth to make the fastening effect good.
Features:
Specs:
Size | M4x8mm |
7. 40Pcs Anwenk 1/4"-20 x 15mm Furniture Screw in Nut Threaded Wood Inserts Bolt Fastener Connector Hex Socket Drive for Wood Furniture Assortment (with Hex Spanner)
- 40pieces Pack of Furniture Screws Threaded Inserts for Wood Furniture.
- Size: Internal Thread Insert Type: 1/4"-20, External Diameter: 10.5mm, Total Length: 15mm. (1/4"-20x15mm)
- Material: High quality carbon steel with high hardness. These furniture screws are wear-resistant and very durable to use. Standard internal hex socket type without burr and non-slip design.
- Usage: Pre-drill /drill a well-sized hole (Suggest that the diameter of the hole is 9.6 +/- 0.2mm, the length is about 18mm), then use a 6mm internal hex tool to screw in (6mm Hex Spanner Included). Tip: If the furniture wood is with high-hardness, please enlarge the screw hole.
- Applications:These furniture screws are suitable for furniture hardwood/ solid wood, for furniture combinations.
Features:
Specs:
Color | 1/4"-20 x 15mm Furniture Screw |
8. 40pcs 1/4-20 Threaded Inserts Screw in Nut Insert Nutsert for Wood Furniture
- 1/4"-20 wood threaded insert x 15mm length.
- Furniture connector bolts 1/4-20 screw in nuts.
- Ideal for furniture and wood projects.
- Material: Zinc Plated carbon steel, features durable construction for a long-lasting hold.
- Hex Drive:6mm, recommanded drilling bit: 3/8" / 9.5mm drill bit.
Features:
Specs:
Size | 1/4-20 x 15mm |
9. E-Z Lok Threaded Insert, Zinc, Hex-Flanged, 3/8"-16 Internal Threads, 13mm Length (Pack of 25)
- Inexpensive thread repair solution for soft woods, MDF, plywood, etc.
- Install with hex key or optional drive tool
- Flanged design sets installation depth
- Country of origin: United States
Features:
Specs:
Height | 0 Inches |
Length | 13 Inches |
Number of items | 25 |
Size | Hex" |
Weight | 0.01 Pounds |
Width | 0 Inches |
10. E-Z Lok 400-5 Threaded Insert, Brass, Knife Thread, 5/16"-18 Internal Threads, 0.625" Length (Pack of 10)
- THREADED INSERTS FOR WOOD ā E-Z LOK Thread Inserts for hard-wood are ideal for applications where stripping or thread erosion is possible. Perfect for furniture, cabinets, displays, and more.
- PROPRIETARY KNIFE THREAD ā E-Z Knife thread inserts provide superior holding power using a proprietary external āknifeā thread to slice into the wood.
- BRASS OR STEEL OPTIONS ā Brass threaded inserts or stainless steel threaded inserts available. Stainless steel is recommended for particularly hard wood and anywhere corrosion resistance is needed.
- FOR USE WITH APPLICATIONS ā The E-Z Knife threaded inserts for wood are designed for use in hard woods such as oak, cherry, and maple.
- STRONG THREADS MADE EASY ā Easily installs with a screwdriver, bolt/jam nut, or an optional E-Z LOK drive tool.
Features:
Specs:
Height | 0 Inches |
Length | 0.625 Inches |
Number of items | 10 |
Size | 5/16"-18 |
Weight | 0.03 Pounds |
Width | 0 Inches |
š Reddit experts on nut inserts
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where nut inserts are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
>Does't seem sturdy enough if I wanna put my feet up :(
If it's made from chipboard / particle board you probably wouldn't want to do that anyway :-) But if you made it from plywood it would be plenty strong enough.
Those metal locking nuts /u/doc_lock is describing are actually quite secure, but they do favour easy disassembly over strength. This is what they look like, along with their associated bolt.
If you're doing docker why not k8s? :)
Or look at your other options. Ubuntu is great, but there are a few OSs particularly for docker containers like rancheros that will reduce overhead and streamline deployment.
And I mod a lot of my gear. I would consider stringing them on a couple rods or building a tower. The rods would be nice because you could hang them in a rack :).
Edit: by rods I mean a couple of these guys cut to length (also available shorter and cheaper, but the are 2x rack length). Just get some matching nuts and bam, instant rack. If you want a non-rack form factor something else may better allow for swapping out parts and mounting fans. If rack mount, hang that from a shelf, load the shelf with psus. Just use 80mm (not 120) coolers to maximize packing :)
Everybody is bad-mouthing it but nobody is offering advice.
You can salvage this if you lay a piece of 3/8" over the top of the control board and undermount the joysticks. Then use some of these to undermount the joysticks. They will show through the top though, so get yourself some spray adhesive and some laminate/melamine to cover the top of it.
Secondly, the piece that your monitor is mounted to and that (what appears to be) an audio controller... Redo it and this time take your time and use measurements and a template.
Cardboard is your friend. Use it to template things with exact measurements. Use a ruler, a straight edge, and a nice pointy pencil.
You've got this!
No problem!
Sure thing!
A lot of these were purchased on Amazon for this build, but I do a lot of electronics tinkering, and I usually grab this stuff from Aliexpress and just wait the 3-6 weeks for it to arrive in the US. I had one Pro Micro on hand, but needed two, so I just got the 3 pack from the Amazon seller below:
Pro Micros
https://www.amazon.com/gp/product/B01HCXMBOU
Bumpons
https://www.amazon.com/gp/product/B01ACPT2LU
M3 Inserts
https://www.amazon.com/gp/product/B00Y20YLKY
Female Micro USB Breakout Boards
https://www.amazon.com/gp/product/B0183KF7TM
RJ9 Adapter Kit (these can be gotten cheaper, but I needed them fast)
https://www.amazon.com/gp/product/B072HXNW3F
RJ9 Coiled Cord
https://www.amazon.com/gp/product/B076J83H83
Silicone Hookup Wire (good looking and easy to work with)
https://www.amazon.com/gp/product/B073RD76QD
Female Headers (just snap off and sand the broken edges)
https://www.amazon.com/dp/product/B01DLX6RSQ/
I've found them a bit hit and miss, I used them on drawer handles, which may not be the ideal use case. One of 5 has already come loose. I tried to fix by shoving PLA fibres after it and melting a rim around, but no joy.
The surface area of the grip part is very small on the ones I have, and also the lines down the edge run lengthways, where if they have been crossways they'd have been like knurling adding some grip.
I got mine on amazon and ebay. https://www.amazon.co.uk/M3x5mm-Metric-Threaded-Insert-100pcs/dp/B00Y20YLKY/ref=sr_1_6?ie=UTF8&qid=1539132205&sr=8-6&keywords=threaded+inserts
I've started to (where possible) build little enclosures for nuts instead. It's a lot more hassle and less fun.
Any tips on the inserts welcomed (I bought a bloody load of them)
Here are some on Amazon, Prime-eligible. I'll probably get a larger batch too, but these are relatively cheap to play with and they get here fast. :-)
The GPU is simply mounted to the wood with a screw like it would be in a case, there's a little support that I covered with silicone on the back end.
For the motherboard I used these and these.
Nice! I left the middle parts solid and used a cordless drill to make the holes. I figured since I'll never take them apart, they won't become stripped. I've also seen serrated brass nuts pressed/melted in with a soldering iron. It creates a durable threaded hole:
M3x5mm(L)-5mm(OD) Metric Threaded Brass Knurl Round Insert Nuts 100pcs https://www.amazon.com/dp/B00Y20YLKY/ref=cm_sw_r_cp_api_-S2-BbYAV507F
use threaded inserts instead of trying to thread into the print it's self. I use these: https://www.amazon.com/gp/product/B00Y20YLKY/ref=oh_aui_detailpage_o01_s01?ie=UTF8&psc=1
Just look on Amazon for threaded inserts in what ever size you want. I am using the ones I posted along with nylon screwed so I'm not conducting electricity from what ever I am fastening down. I do have stainless steel ones I use too for parts that need a stronger fastener.
Check out this post from 3Dhubs on threaded inserts: http://www.3dhubs.com/knowledge-base/how-assemble-3d-printed-parts-threaded-fasteners
I've been using these: Glarks 370Pcs M2 M3 M4 M5 Female Thread Knurled Brass Threaded Insert Embedment Nut Assortment Kit for 3D Printing https://www.amazon.com/dp/B07L96KVP3/ref=cm_sw_r_cp_apa_i_y9eZDb0HFEHM9
I suspect they're not as resistant to shear as the McMaster ones, but they're way over spec for anything I've needed, and they're all nicely threaded. I've also fused a bit of filament inside when I've needed them to be locking nuts.
Get some threaded inserts ( like these ) so you don't break the wood if they get moved
you could do that or use 3/8" threaded inserts embedded from underneath the ply. Then when you want to use the saw just drop bolts and washers through the feet into the inserts.
My current tap handles are wooden children's alphabet blocks from a flea market with these inserted.
Anything can be a tap handle if you can drill a hole in it to insert those.
https://www.thingiverse.com/thing:3663683
I used a threaded insert instead of just screwing into the plastic.
I get them on amazon.
Lock in screws is how I did this for a few pieces these the are the ones I used: 40Pcs Anwenk 1/4"-20 x 15mm Furniture Screw in Nut Threaded Wood Inserts Bolt Fastener Connector Hex Socket Drive for Wood Furniture Assortment https://www.amazon.com/dp/B07HR63VF5/ref=cm_sw_r_cp_apa_i_SN4OCb2CHT01F
It's a threaded wood insert screw. Something like these.
E-Z Lok Threaded Insert, Zinc, Hex-Flanged, 5/16"-18 Internal Threads, 25mm Length (Pack of 25) https://www.amazon.com/dp/B002WC8TV6/ref=cm_sw_r_cp_apa_i_HGuEDbNCDTXEB
40pcs 1/4"-20 Furniture Screw in Nut Threaded Insert Nutsert for Wood Furniture Connector 15mm Length https://www.amazon.com/dp/B07Q6HKK45/ref=cm_sw_r_cp_apa_i_dHuEDbBKV3F74
The ones you have in those legs are screwed in with an Allen wrench.
I completely lied without intension. I looked back at my amazon order and realized that its 5/16. Still plenty for the task bc I zig zagged them but nowhere near 5/8"! Thanks for catching that. This is where I got them from
What you're talking about is called a cam fitting or a cam lock: http://www.amazon.com/Uxcell-a12010500ux0151-Furniture-Fitting-Pre-inserted/dp/B00880QVTS
Those types of "joinery" methods are not very strong. All my ikea furniture is now very loose and racks around like crazy.
You would be much better off screwing it with a countersunk hole and covering up the screws by glue a decorative wood veneer or just a thin piece of wood as an accent or something.
You could also consider pocket holes and use plugs to fill and finish the holes.
Following up on the original comment... Don't use these. They're damn near impossible to get perpendicular to the surface of the wood and they're way more expensive than blind nuts.