Reddit mentions: The best roof flashings
We found 16 Reddit comments discussing the best roof flashings. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 14 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Patch & Shield Power Tape Black - All Weather Patch Tape | Stretchy Sealing Tape for Roofing, Waterproof Tape for Pipes | Patch Holes & Cracks | Butyl Tape 4 inch x 5 feet
- SOLVE ANY SEALING PROBLEM: Gaffer Power's Power Patch Tape brings you a dynamic, flexible butyl tape that creates professional-grade sealing results in a pinch and in the long term. Say goodbye cracks & holes and apply 4” wide tape for the perfect roof patch, nail hole patch, pipe & gutter leaks – Use as outdoor shed or greenhouse repair tape!
- 100% WATERPROOF KEEPS YOU DRY: Our adhesive patch tape is expertly engineered to hold water in or keep water out wherever you need it. 100% Waterproof tape works to fix leaky above-ground pools, water tanks, drums & storage containers - creating a tight, even seal that increases with pressure. Every American homeowner should have this tape in their back pockets.
- HEAVY DUTY ALL-WEATHER USE: Don't get stuck out on vacation with a leaking RV or tent, or at home worrying about catching drips from the ceiling after whipping wind & storms. Gaffer Power's heavy duty waterproof tape is designed with an ultra-strong adhesive backing that sticks to any surface and holds up dutifully under conditions of extreme cold, sweltering heat, dampness & moisture or mold & mildew. Active from -70 to 200 degrees F
- UNRIVALED MADE IN USA QUALITY: Gaffer Power is committed to our Made in USA engineering process. This sealant tape is manufactured under the strictest quality assurance guidelines with the best US sourced materials. Power Patch waterproofing tape is American built to last.
- THE GAFFER POWER GUARANTEE: We know you'll love the endless uses you'll find for our roof waterproof patch tape. Issues aren't common when it comes to the best patch tape on Amazon, but if anything is wrong we stand by our commitment to quality and offer a Guaranteed Replacement or Your Money Back.
Features:
Specs:
Color | Black |
Weight | 0.44 Pounds |
Size | 4 Inches X 5 Feet |
2. DIY Rubber Roof (EPDM) Repair Kit: Tools + Cleaner + Primer + Flashing Tape - Everything You Need to Fix Rubber Roof
DIY Repair Repair Rubber Roof Yourself - FREE SHIPPING Materials [Made in & ships from US]For EPDM Rubber Roofs on Home, Business or RV/Motorhome (black or white)Save $100s by Fixing Rubber Roof YourselfFor use by Homeowners and Small BusinessesIncludes All Required Tools and Materials Need to Fix E...
Specs:
Color | Black |
Height | 14 Inches |
Length | 11 Inches |
Weight | 9 Pounds |
Width | 6 Inches |
3. 280DC - White Elastomeric Roof Coating
- 5 gal pail
- Water soluble for easy clean up
- Reflects 88% of the suns heat.
- CA Title 24
- 10 Year Warranty
Features:
Specs:
Color | White |
Size | 5 gal |
4. The Ultimate Pipe Flashing (4" Boot)
#400 fits PVC & ABS 4" pipeProprietary PVC compression collar prevents relaxation from pipeGuaranteed for the life of the shingle, cedar, tile or slateGenerous flashing, Kynar brown finish, 24 gauge galvanizedAccommodates flat to 18/12+ pitch
Specs:
Color | Brown |
Height | 6 Inches |
Length | 20 Inches |
Weight | 4 Pounds |
Width | 15.5 Inches |
Size | 4" Boot |
5. Dektite #3 Red Silicone Metal Roof Pipe Flashing, High Temp, Round Base, Pipe OD 1/4" - 5"
- Flashing Base Diameter is 8" - Fits 1/4" to 5" Outside Pipe Diameter
- Continuous Service High Temperature Ranges of -58F to 392F (Silicone)
- If Trimmed and Installed Correctly, Pipe Flashing Will Not Break or Crack
- Use for Stove Pipes, Chimneys, Plumbing, Heating, Air Conditioning, Electrical, and Exhaust Vents
- 20 Year Manufacturer's Warranty Against Manufacturing Defects
Features:
Specs:
Height | 4 Inches |
Length | 8 Inches |
Weight | 0.47 Pounds |
Width | 8 Inches |
6. Magerack Black L-Foot Bracket with Black Flashing for Solar Panel PV Module Mounting Racking 3/8" Slot Pack of 10
- Patented flashing design, absolutely waterproofing
- Extremely easy to install at lowest cost
- Compatible with most common rails from rail manufacturers
- 571 lbs uplift and 536 lbs downforce
- The vertical slot is for up to 3/8" bolt or 5/16" bolt as specified, through which a fastener is attached to rail
Features:
Specs:
Color | Clear |
Size | L-foot Black |
7. Dektite Premium #6 Red Silicone Metal Roof Pipe Flashing, High Temp, Square Base, Pipe OD 5" to 9"
- Shrink-wrapped
Features:
Specs:
Height | 6 Inches |
Length | 14.25 Inches |
Weight | 21.4 ounces |
Width | 14.25 Inches |
8. Dektite #8 Red Silicone Metal Roof Pipe Flashing, Round Base, Pipe OD 7" - 13"
- Fits 7" to 13" outside pipe diameter. Round base diameter is 16-1/2".
- Continuous service temperature ranges of -58°F to 392°F (Silicone).
- Will not crack or break.
- Flexible aluminum collar.
Features:
Specs:
Height | 5.5 Inches |
Length | 16.5 Inches |
Weight | 33.3 ounces |
Width | 16.5 Inches |
9. Cofair QR625 Quick Roof Pro Aluminum 6" x 25'
Instant waterproof repair100% UV stableSelf-stick aluminum surfaceSelf-seals around screws and fastenersMade in the USACo-Fair Instant Waterproof Repair and Re-RoofingSelf-stick aluminum surfaceSuper reinforcedJust press in place for a permanent repairFive puncture resistant layers, 10 year material...
Specs:
Color | YELLOW |
Height | 6 Inches |
Length | 6 Inches |
Weight | 3.6 Pounds |
Width | 6 Inches |
Release date | March 2014 |
Number of items | 1 |
10. AMERIMAX HOME PRODUCTS 66320 20-Inch x 10-Feet Aluminum Flashing
- The product is 20"x10' alum flashing
- Easy and simple use kit
- The product is manufactured in china
- Composed of durable, refurbished aluminum
- Quick, easy repair for roofs and gutters
- Immediately stops leaks
- Composed of durable, refurbished aluminum
- Quick, easy repair for roofs and gutters
- Immediately stops leaks
Features:
Specs:
Height | 3 Inches |
Length | 19 Inches |
Weight | 1.8 Pounds |
Width | 3 Inches |
Size | Pack of 1 |
Number of items | 1 |
11. Amerimax Home Products 20" X 10' Copper Flashing 67320 Copper Flashing & Valley
- The product is 20"x10' Copper flashing
- Easy and simple use kit
- The product is manufactured in china
- Composed of hardened, durable copper
- Quick, easy repair for roofs and gutters
- Functions as roofing material, termite shield and various other purposes
Features:
Specs:
Height | 19 Inches |
Length | 9 Inches |
Weight | 16.7330856858 pounds |
Width | 9 Inches |
Number of items | 1 |
12. ProLine Plank Flashing (6" Aluminum Butt-Joint Flashing)
use with any fiber cement planksno need to caulk the butt-jointdesigned to prevent water penetration
Specs:
Color | Navajo Beige |
Height | 5 Inches |
Length | 7 Inches |
Width | 6 Inches |
13. Dektite #2 Gray EPDM Metal Roof Pipe Flashing, Round Base, Pipe OD 1-3/4" - 3-1/4"
Specs:
Height | 3.75 Inches |
Length | 6.38 Inches |
Weight | 0.37 Pounds |
Width | 6.38 Inches |
14. XFasten Waterproof Patch and Seal Tape, White, 4 Inches x 10 Feet, Water Barrier Tape for Stop Leak Repair on Pipes, Chimney, Roof, Boat, and HVAC
- Input interface: M-Key M.2 NVME ( Don't Support SATA Protocol m.2 NGFF )
- Output interface: PCIE X16/X8/X4
- Support Devices: NVME NGFF Key M SSD
- Support system: Windows7/8 / 10 / Linux
- Product dimension: 90x32mm(LXH)
Features:
Specs:
Color | White |
Height | 5.905511805 Inches |
Length | 4.724409444 Inches |
Weight | 0.57 Pounds |
Width | 4.724409444 Inches |
Size | 4-Inch x 10-Foot |
🎓 Reddit experts on roof flashings
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where roof flashings are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
I used butyl tape on my Pontiac Vibe and it worked really well for soundproofing (two layers on the doors, one layer in the hatch area). Similar to this but the stuff I bought at home depot was about 2 feet wide instead of 4 inches. A lot of automotive sound deadening stuff is basically this stuff with a markup. It's flexible and sticks pretty well, but you might want to use additional spray adhesive if you're doing your ceiling. It looks like you already have soundproofing material on your floor?
For my project, I plan on putting butyl tape on the metal, then foam board on top, then plywood. Haven't decided yet between EPS or XPS foam board (EPS is vapor permeable and XPS is not) but they're both moisture resistant with the tradeoff of lower R-value over other options, like fiberglass batting (degrades with moisture) or polyisocyanurate (useless under 50F)
I have not replaced the rubber on my roof but I have worked on it in the past. It sounds like your roof is an EPDM roof. Which, as you have seen, is made by putting a complete piece of rubber over the roof and then sealing it to the roof.
EPDM rebuild kits are available. Essentialy you have to clean up and prep the area that needs replacement, then put the new piece of EPDM in place. The edges that would overlap flat on the roof could be sealed with a combination of eternabond and dicor. The part of the roof that goes around the edge of the camper might need some more thought. Mine is rolled and has gutters along with downspouts along the edge. In my estimation that would be the hard part. Sealing the roof where it meets the body of the camper.
I am pretty sure it can be done if you are handy and take your time to properly prep at each step. (I learned that this summer when I redid my roof).
It depends on a lot of things so try and get some pictures of the leaky area when you get up there. But it shouldn't be that hard. Use a scraper and get off all the more caked up and loose coating removed. Then apply Henry's elasotmeric:
http://www.amazon.com/280DC-White-Elastomeric-Roof-Coating/dp/B00GMMQXUQ
That's a five gallon bucket which is probably enough to coat an entire single-wide mobile home roof. You probably don't need that much. It comes in one gallon and maybe even in quarts.
You just paint it on with a brush. Don't apply it in super cold weather or it won't dry right.
Get some pics and I can give you a better idea of what it is you need to do.
Also you can post on /r/DIY (do it yourself) They are very helpful there. They will want to see some pic to.
Since you own the house and live in a cold area I would suggest getting good pipe flashing and having a roofer install it ($250 or so for the install). You will have 4" PVC running up out of it with some sort of cap. You will want it as close as possible to the fan and going up through the roof vs. out the side of the house under the eaves and possible soffit vents.
https://www.amazon.com/Ultimate-Pipe-Flashing-400-fits/dp/B007TJP6BI
For the inside, between the fan and the roof, you will want to have an insulated pipe so you're not building up condensation.
edit:
http://www.chicagotribune.com/sns-201506152000--tms--askbildrctnab-a20150626-20150626-story.html
Meh, it should work. You may need to seal the door with fireproof rope and stove cement. I got some at a local stove store when my cubic mini started leaking. It was quite noticeable, the smell, and my co detector noticed too. As another commenter mentioned, having a cracked window is essential to allow draft to evacuate smoke. If you can find it, double wall pipe is way way safer and more functional. It says Pipe Diameter: 3.375", so maybe double wall pipe from the dickinson or cubic mini would work.
Otherwise, I'd recommend putting some chicken wire around the stove pipe, and also make a wire cage all around the stove, because it's impossible to completely avoid clothes/bedding falling on the stove in such a small space, while you're asleep. It's happened to others, and it's one of the reasons I use my china diesel heater while I'm sleeping.
TBH, it's kind of a pain trying to stay warm for 8 hours overnight with a wood stove, while maintaining fresh air. Your stove might be up to the task, but mine is too small (cubic mini cub) so I used to wake up cold af, no matter how low I'd turn it down.
Smoke getting in the van isn't an issue for me, long as you close your fan and crack a window. A propane torch helps to start it up, and those waxy logs from winco/walmart are great for starting a fire with little smoke. Coal produces very little smoke, but a lot of CO and it produces less draft which can make the CO waft in your van if it's not burning strong, with the intake wide open.
To get around clearance requirements in a small space, construct a radiant barrier of two pieces of aluminum/steel sheet, with stacked washers/nuts/etc as spacers, to create an air gap in between the plates. I did this with my stove and the bottom plate under my stove was cold with it running.
For the roof, use a Dektite #3 red hitemp fitting, with some hitemp caulk from ace, and bolt the fitting to the roof before the caulk dries. Leak proof for over a year for me.
https://www.amazon.com/Silicone-Flexible-Pipe-Flashing-Dektite/dp/B077QM5VT8
You can mount it through the roof or through the wall. There are a few different ways to do it, but a lot of people get a Silicone Chimney Flashing making it easier.
This worked great for me and was hard to find:
Dektite Premium #6 Red Silicone Metal Roof Pipe Flashing, High Temp, Square Base, Pipe OD 5" to 9" https://www.amazon.com/dp/B0189UGN76/ref=cm_sw_r_cp_apa_i_cgIUDb6HK2YNM
Example of way to keep water out
Roof Protector thingy
Basically the rail system secures it to roof and these protect the screws into the stud from having water. They slide up under the shingles to the point of water shed is on top and can’t get below.
I would use marine grade 3/4" tongue and groove plywood, and flash it with wide strips of aluminum bent into an 'L' shape:
https://www.amazon.com/AMERIMAX-PRODUCTS-66320-Aluminum-Flashing/dp/B000DZGHHC
I used quickroof for the trunk of my car. My car is much quieter on the outside and the bass seems louder on the inside. Way cheaper than dynamat type products.
I'm sure it may depend on what grade of AL is in use, but flashing is dirt cheap. 20 inches by 10 feet. Etch until you're blue in the face.
Find ways of protecting yourself while you're sitting still and sleeping, as that's when you're most vulnerable. I've written about radiosurgery, which is the act of destroying select tissue with electromagnetic radiation. There's a real threat of permanent brain damage. Do what it takes to stay healthy.
What is your budget?
I've tried the following (from /r/emshielding sidebar):
I would recommend instead of the above (which was me prototyping and testing vectors), do it the right way the first time, and build my ventillated sleeping enclosure (~$1,000 for aluminum, plus add'l layers), and coat it with layers of shielding materials (copper flashing > butyl > sheet steel > buytl > sheet lead > butyl), until you achieve complete relief. Don't skimp on the fans and power supplies.
This isn't unusual for fiber cement siding (or really, ANY siding, but fiber cement in particular). However, the installer should have flashed behind the butt joints with some sort of metal flashing in the first place, instead of caulk. Trying to fight the expansion and contraction with caulk will never work. There are companies that actually make pre-bent flashing just for this purpose. The flashing is dark colored so it doesn't pop out as much when the siding contracts.
XFasten Waterproof Patch and Seal Tape, White, 4 Inches x 10 Feet, Water Barrier Tape for Stop Leak Repair on Pipes, Chimney, Roof, Boat, and HVAC https://www.amazon.com/dp/B07QYBFHRY/ref=cm_sw_r_cp_apa_i_s6BTDbF28WXBF
I use waterproof tape. There was a skylight in this house when we moved in.... and well, this tape came i really, really handy.
Use oil or Vaseline on your scissors to cut it, and use small pieces at a time to avoid it sticking to itself, because you can't unstick it.