Reddit mentions of ANEX Ultra Low Profile Offset Screwdriver Set 3 Piece, 90 Degree Straight Slim Plate For Tight Area, Made in Japan, Black

I'm guessing there's some way to pop off the tilting mechanism, but if not these are the lowest profile screwdrivers you can get.

If you ever need to get into really tight spaces, these saved a shelving project I did a while back.

Mastercraft is fine for some tools though I would not suggest that blue box shown in your ad photo. I had one as a beginner box (since it was on sale and I needed something cheap at the time) and it's not very good. That box easily tips over if more than 2 drawers are open which by itself would be fine if not for the fact nothing holds those drawers shut so if your box is on even a slight incline the drawers tend to want to slide open. Well that and I outgrew that box pretty quick so honestly I would suggest like others have mentioned to check the used market, whether through a tool truck or Kijiji, Craigslist, etc as you will often get much better value for your money.

In terms of hand tools the MAXIMUM line is pretty decent to start out with if you get it on sale but never pay full price for anything at Canadian Tire if you can avoid it, it's rarely worth it at full price (ex. Most MAXIMUM air tools cost as much or a little less than Ingersoll Rand when not on sale). My diamond driver screwdrivers and bolt extractors have worked quite well and a few of my coworkers have purchased that MAXIMUM die grinder and liked it, though personally I stick with Ingersoll Rand or AIRCAT for air tools.

Another thing to keep in mind to is many professional brands, including Snap-On, do not produce every tool that bears their name. Instead another manufacturer makes them and simply brands the tool with their name and at the same time produces the same tool under their own name for much cheaper. A perfect example is these low profile screwdrivers. Snap-On was advertising just the number 2 Philips (with their name on it) in a past catalog for around $20 or you can buy the whole set of 3 from the original manufacturer for a couple of bucks more. It's always worth looking into whenever you might need to purchase a tool.

You're driving at quite the angle there. Better option is to use a small diameter, long bit with some painter's tape either on the bit or handle.

Here are some such bits: https://www.amazon.com/Phillips-Magnetic-Professional-Screwdriver-Production/dp/B07GPD3B96

If you want it real snug, then these are better than offset screwdrivers:

https://www.amazon.com/Anex-6102T-Profile-Driver-Handle/dp/B0016VAIBI

http://i.imgur.com/lr2wjGW.jpg there are two screws that i cannot get with a screw driver... Maybe using a very small allen wrench can get them but even that is hard to find

[https://www.amazon.com/dp/B0016VAIBI/ref=cm_sw_r_awd_kzybvb173A7CZ]
(https://www.amazon.com/dp/B0016VAIBI/ref=cm_sw_r_awd_kzybvb173A7CZ) i found this buy $18?? Really?

this will do it https://www.amazon.ca/Anex-6102T-Profile-Driver-Handle/dp/B0016VAIBI

[This would probably work.](http://www.amazon.com/Anex-6102T-Profile-Driver-Handle/dp/B0016VAIBI/ref=pd_rhf_dp_s_cp_5_N7MF?ie=UTF8&refRID=040JJ0P4FEWZRNRWTDZX
)

Low profile screwdriver. Saved me from taking the flaps back off.
https://www.amazon.com/Anex-6102T-Profile-Driver-Handle/dp/B0016VAIBI/ref=sr_1_2?ie=UTF8&qid=1539793196&sr=8-2&keywords=low+profile+screwdriver#sp_detail_feedbackForm

I've used one of these to get to screws holding in window trim on a car, I ground off the flat bit on the other side:

https://www.sears.com/craftsman-offset-ratchet-screwdriver-set/p-00904116000P?gclsrc=aw.ds&&sid=SLIAx01191011x000001x1979005196&utm_campaign=1026411&utm_group=71283841136-352491908817&utm_term=pla-761465361272&gclid=EAIaIQobChMIg4CN5LDA5AIV5__jBx0JTgDNEAQYAiABEgIocfD_BwE

There's also this:

https://www.amazon.com/Anex-6102T-Profile-Driver-Handle/dp/B0016VAIBI

I've also used a shortened Philips bit in a quarter-inch ratcheting wrench, held in place with hot glue. When I was done, I warmed it up with a propane torch to loosen the glue, then cleaned all the glue off. Here's an example before cutting off the unused part of the Philips bit:

https://i.imgur.com/jLmcVML.jpg

As a fellow 60 guy I strongly suggest these:

Anex 6102T Ultra Low Profile Screw Driver Handle https://www.amazon.com/dp/B0016VAIBI/ref=cm_sw_r_cp_apa_i_4M8gDbY8YCDK3

They make life a lot easier is several locations such as the M/R de-ice harness and in the broom closet. Made in Japan.

I have a set of these that work wonders in tight spaces:
https://www.amazon.com/dp/B0016VAIBI/

$15 might be a bit steep if you're not a tool hoarder like me, but there are plenty of good alternatives for under $10 in the related products lists. Good luck!