Reddit mentions of Meguiar's M10508 Mirror Glaze Ultra-Cut Compound, 8 Fluid Ounces, 1 Pack

I would have taken more photos but I didn't set out with the intention of making a post; however, when I saw the results I knew I had to.

Like I said, this mini van only set me back $300. But just because it's a cheap turd doesn't mean you can't take some pride in it and at least put a ribbon on it.

Anyways, I'll add some more details left out of the post.

First I mixed up regular ole dish soap and water and grabbed some 1000 grit wet/dry sand paper, dunked it in the solution and let it soak while I taped off my headlights. I don't think you have to let it soak, but that's what I did. Once I finished taping off the lights, I started wet sanding and just redunked as needed for adequate lubrication.

Now I've read some posts on here about people saying it's easier to see when you're done sanding if you go in one direction for a certain grit and the opposite in another so you can see sanding lines. I didn't do that either. I just sanded it til I felt it was smooth and/or had been doing it for a couple minutes; up, down, left, right, circles. Whatever. It worked out for me.

Repeat exact same procedure for 2000 grit wet/dry sand paper.

Now, if you've never done this before you might start to get nervous, because at this stage your headlights look (somehow) even worse than when you started. Fret not my friend. Patience is a virtue.

Now I have a DA polisher, but these headlights are narrow. So I opted at just purchasing a generic named 3" backing plate, drill adapter and pad combo set off amazon. Some of the reviews said it wasn't the greatest. But that was fine by me. I just wanted them for this headlight. Those reviewers are wrong. I think they were thinking you could do an entire vehicle with these 3" pads. The pads and backing plate were high quality and for that price, even if they weren't I wouldn't have been all that upset. I highly recommend these.

I used the two flat top oranges pads for this project. First I used M105. Polished til it "flashed" then buffed it off with a microfiber towel. Switched to my other orange pad and polished with M205 following the same procedure.

Then I stood in awe of how great they came out. Did a wipe down with isopropyl alcohol, and two coats of collinite 845 that I applied with some cheap microfiber applicators for future uv protection.

Then I went and excitedly rushed my girlfriend outside to see. She was impressed but decidedly less than me.

Also, while I was doing this, a man approached me and asked me how much I'd charge to do his car. I talked with him a bit, and informed him that for the price I would charge to do his one car he'd be better off doing some research, buying his own supplies and just learning a new skill. He thought about it and excitedly told me he already had a drill and that he decided he'd do it. He went on to say he was also going to do not just his car, but also his mom's car and his girlfriend's car. He wrote down everything I said! Haha,I hope his come out as well as mine!

Edit: formatting/spelling

You'll need the proper equipment. Hopefully you already have a buffer and compound?

PM me and we can dig into the details, if you aren't familiar with the polishing process.

great looking pens.

​

for sanding insides: wet or dry sandpaper, water, 320 grit up to 1200 grit, lots of time to stand there and sand b/c it's BORING work, and one of these-

https://www.ebay.com/itm/8-Slotted-Mandrel-1-4-Shank-Body-Split-End-Head-Core-Sanding-Internal-Holes-/221323367298

​

and after that a paper towel instead of sandpaper, and plastic polish. Some of us use headlight polisher from the auto parts stores. I like the heavy cut meguiars, and then a light cut meguiars.

https://www.amazon.com/dp/B003LMGDHI/ref=cm_sw_r_tw_dp_U_x_vnNMDb8YZZX2C

I was also a beginner at the beginning of the year. I went out and bought [Meguiars 105] (https://www.amazon.com/Meguiars-Mirror-Glaze-Ultra-Cut-Compound/dp/B003LMGDHI/ref=sr_1_1?ie=UTF8&qid=1496750162&sr=8-1&keywords=meguiars+105), and [Meguiars 205] (https://www.amazon.com/Meguiars-Mirror-Glaze-Finishing-Polish/dp/B003LMJP4Q/ref=pd_sim_263_1?_encoding=UTF8&pd_rd_i=B003LMJP4Q&pd_rd_r=YK6JBJ416NKY6325PPQG&pd_rd_w=WZ6u4&pd_rd_wg=LD9ed&psc=1&refRID=YK6JBJ416NKY6325PPQG), a [chicago electric DA from harbor freight] (https://www.harborfreight.com/6-in-57-Amp-Heavy-Duty-Dual-Action-Variable-Speed-Polisher-62862.html?ccdenc=eyJjb2RlIjoiODkwMjE0MTgiLCJza3UiOiI2Mjg2MiIsImlzIjoiNDkuOTkiLCJwcm9kdWN0X2lk%0D%0AIjoiMTE0NDYifQ%3D%3D%0D%0A), and ordered [orange and white hex logic pads from amazon] (https://www.amazon.com/Chemical-Guys-BUFX-102-HEX5-Hex-Logic-Medium-Heavy/dp/B0040MI9H0/ref=sr_1_1?s=automotive&ie=UTF8&qid=1496750285&sr=1-1&keywords=hex+logic+pads). This will be a good start. Get these things, should cost between 120 and 150 for all of it depending on where you buy, and that DA goes on sale quite often, looks like it's currently down to 49.99, so now would be the time to buy. I started off doing my Formula and then did my Sierra, and now have had a few other people come to me for correction and have a pretty good grasp on what I'm doing.

1. Watch tutorials by Junkman2000 on youtube.
   
2. Use the right size pads for your backing plate. The DA listed above comes with a 6" flimsy backing plate, and you should replace it with a 5" so it is smaller and easier to work with. Mark your backing plate as well, so if you push too hard, you'll see it stop spinning. Good for figuring out how much force you SHOULD be using.
   
3. Take your time, and work at it slowly, you will have results.

Wash: https://smile.amazon.com/Meguiars-Hyper-Wash-Foaming-Leaves-D11001/dp/B0006SH4IM

Clay: https://smile.amazon.com/Nanoskin-AS-019-AutoScrub-Grade-Sponge/dp/B00CUAWJ6G

Decontamination: https://www.autogeek.net/carpro-iron-x-cleaner.html

DA: https://www.harborfreight.com/6-in-57-amp-heavy-duty-dual-action-variable-speed-polisher-69924.html

Polish: https://smile.amazon.com/Meguiars-Mirror-Glaze-Ultra-Cut-Compound/dp/B003LMGDHI

Compound: https://smile.amazon.com/Meguiars-Mirror-Glaze-Ultra-Cut-Compound/dp/B003LMGDHI

Pads: https://smile.amazon.com/dp/B004104678/ref=twister_B00NN89SGI?_encoding=UTF8&psc=1

Coating and Sealant: https://www.autogeek.net/cquartz-uk-edition.html

Go to Amazon and order this (I like Meg's products),

• Harbor Freight DA
  
  
• Meg's Endurance Tire Gel
  
  
• Meg's Ultimate Protectant
  
  
• Meg's Ultimate Liquid Wax
  
  
• Meg's APC
  
  
• Rag Company's Borderless Blonde
  
  
• Rag Company's Waffle Weave
  
  
• Hex Logic White Pad (3)
  
  
• Hex Logic Orange Pad (2)
  
  
• Hex Logic Red Pad (2)
  
  
• M105
  
  
• M205
  
  
• 3M Auto Tape
  
  
• Mother's Wheel Brush
  
  
• ABN Woolies
  
  
• Trim Brush
  
  
• Chem Guys Wash Mitt (2)
  
  
• Mother's Clay Bar Kit
  
  This should run you about $345 for everything and have you setup to take care of your car for a long time. You can find a 20% discount code online for harbor freight to bring the price down $55 for the DA. Go to home depot and buy a couple buckets and you will be good to go.
  
  Edit: To add, I went to Lowes and bought a cheap inline sprayer for my hose and it works fine for foaming up the vehicle, plus it only costs $5.
  
  Edit2: If you are going to downvote me please post why you don't like my recommendation.

Wow. I should get into paint correction. <$250 for all the tools and polish and waxes. As a car guy, I don't mind waxing my car every 6 months (or 4 months if you're in the frigid north or are anal). I also feel it's foolish to drop $2k-4k on these nano-quartz-bullshit schemes that a lot of car guys swear by nowadays. If you want to drop $4k on paint protection, go for it, but I can get a full window-out repaint for the same price!

Here's what I learned:

Buy the equipment:

https://www.amazon.com/PORTER-CABLE-7424XP-6-Inch-Variable-Speed-Polisher/dp/B002654I46

https://www.amazon.com/Dual-Action-Hook-Flexible-Backing-Plate/dp/B0008G1RDK

https://www.costco.com/Kirkland-Signature-Microfiber-Towel-Case%2C-324-count.product.100341124.html

https://www.amazon.com/Collinite-Liquid-Insulator-Wax-845/dp/B000JK2D06

http://www.autogeek.net/lake-country-beveled-pad-kit.html (MIN: 2 orange, 2 white, 1 black, 1 blue -- I prefer doubling this order; Autogeek almost always has 10-25% off coupons on their mailing list)

You will also need an extension wire with the appropriate gauge (too thin/cheap cables might cause you to burn your Porter Cable motor!)


Buy the compounds (start with UC; if swirls aren't getting cut, move up to 50%/50% UC and 105 on the pads; finish with 205 regardless):

https://www.amazon.com/Meguiars-G17216-Ultimate-Compound-15-2/dp/B001O7PNNM (medium aggressive)

https://www.amazon.com/Meguiars-Mirror-Glaze-Ultra-Cut-Compound/dp/B003LMGDHI (most aggressive)

https://www.amazon.com/Meguiars-Mirror-Glaze-Finishing-Polish/dp/B001O7PNXC

Wash your car with this, and the two-bucket method:

https://www.amazon.com/Meguiars-G7164-Class-Shampoo-Conditioner/dp/B0009IQXFO

https://www.amazon.com/Zwipes-Chenille-Microfiber-Premium-Scratch-Free/dp/B002J7KCOG

Claybar the car:

https://www.amazon.com/YGDZ-Quality-Detailing-Claybar-Shipping/dp/B01MF4BVVS

It took me about 5-6 relaxed hours on a Sunday with a few beers for the full correction. Now I simply top up the wax every few months (and that only takes 30 min).

The thing is, once you do the full correction and get rid of all your swirls and scuffs and whatever clearcoat damage (wash + claybar + M105/UC + M205 + wax), then you don't have to do the FULL correction ever again.

Ever again meaning, if you wash the car properly thereafter with the two-bucket method. You'll simply need to top up the wax once it stops beading -- the wax will protect the clearcoat from damage and swirls.

My wax lasted 6+ months being daily driven in the California sun with three coats of Collinite 845 -- I assume if yours will see more snow and ice and rain, perhaps it'll only last 3-4 months. But since a bottle costs <$20 and you'll get at least 36+ layers out of it, I always recommend this versus the "nano coatings" that people are shelling out $2-4k for.

Here's the Collinite fanboy thread:

https://www.autogeekonline.net/forum/how-articles/40243-collinite-845-definitive-how-guide-legendary-wax.html

Any other questions, feel free to ask. Good luck!

I use Meguiar's M105 then M205 on my headlights.

How many passes do you do per section with your random orbital?

In my situation, I've got a car with spiderweb swirls on the paint. They cover a lot of paint but are very light scratches; they can only be seen in direct sunlight.

I have used these following products on my swirls but it seems that they did absolutely nothing to the paint or the scratches.
meguiar's buffing pad
http://www.amazon.com/gp/product/B0002UQAXY/ref=oh_details_o00_s00_i01
meguiar's m105
http://www.amazon.com/gp/product/B003LMGDHI/ref=oh_details_o02_s00_i07
Do you have different suggestions for products or am I most likely using incorrect technique?

I was looking at this stuff but I have no idea if it'll work for this type of damage.

Wax will just cover it up, if you want to remove the scratch you need to rub it out with polish. I've had some success with Meguiar's M105 cutting compound + M205 swirl remover. Keep in mind, polish is actually an abrasive so don't go overboard. If you just rub it by hand you should be safe. Links: M105, M205, but any brand should work similar.

I wrote a small guide on machine polishing, you can find it here:

[Guide] The Getting Started into DA Polishing

I really like my Lake Country pads, but I've heard good things about other brands like Hex Logic. If you can get LC pads, pick up Orange(compounding), white(polishing), black(waxing).

For a compound, I always suggest
Meguiar's M105/Meguiars M205.

Always try the least aggressive method first, so polish before compound, then move to compounding if you were unsuccessful with just polishing.

I like Collinite 845 for wax, but there are plenty different brands out there to try out.

A Porter Cable is a good polisher, and it will definitely save you time while detailing.

Am I on the right track? I am currently looking for all the products I need to completely detail my car. I know there is no way I could purchase all of these at once, so I am planning on purchasing the major ones first and adding the others over time. I have spent almost two weeks researching on everything I need to do. There is so much information and so many opinions that it is hard to find a definitive answer on what I need.

> Wheel

Wheel soap:

• Meguiar's Non-Acid Wheel & Tire Cleaner D143
  
  Wheel cleaner:
  
  
• Sonax Wheel Cleaner Plus
  
  Tire dressing:
  
  
• Optimum Opti-Bond Tire Gel
  
  Wheel wax:
  
  
• Collinite Liquid Insulator Wax #845
  
  > Paint
  
  Paint soap:
  
  
• Meguiar's Gold Class Car Wash Shampoo & Conditioner
  
  Paint soap addition:
  
  
• Optimum No Rinse Wash & Shine
  
  Leaf blower:
  
  
• Worx Turbine WG520
  
  Clay bar:
  
  
• YGDZ Auto Detailing Magic Claybar
  
  Dual action polisher:
  
  
• Heavy Duty Dual Action Variable Speed Polisher from Harbor Freight
  
  Backing plate:
  
  
• Astro 5" PU Velcro Backing Pad
  
  Pad:
  
  
• Lake Country 5.5" CCS Orange Polishing Pad
  
  
• Lake Country 5.5" CCS White Smart Pad
  
  
• Lake Country 5.5" CCS Black Finessing Pad
  
  Compound:
  
  
• Meguiar's M105 Mirror Glaze Ultra-Cut Compound
  
  Polish:
  
  
• Meguiar's M205 Mirror Glaze Ultra Finishing Polish
  
  Sealant/wax:
  
  
• Collinite Liquid Insulator Wax #845
  
  > Interior
  
  Carpet cleaner:
  
  
• Adam's Carpet & Upholstery Cleaner
  
  Dashboard cleaner:
  
  
• Nextzett Cockpit Premium or Meguiar's Ultimate Interior Detailer
  
  Leather cleaner:
  
  
• Nextzett Cockpit Premium or Meguiar's Ultimate Interior Detailer
  
  Leather conditioner:
  
  
• Lexol Leather Deep Conditioner
  
  Glass cleaner:
  
  
• Rain-X Glass Cleaner
  
  There are a bunch of other tools not listed here, but the ones listed above are the areas I am most concerned about.
  
  > Other Concerns
  
  I am still anxious about spraying water in my engine bay, so I decided to use a spray bottle with soap and water and a microfiber towel to wipe down the engine bay while it is still decently clean. Can I use diluted Meguiar's D143 or will I have to purchase Meguiar's D101 instead? Can the Optimum Tire Gel be used on the black plastics of the engine bay, as well as the other black trims of my car?
  
  I want to protect my interior, in addition to cleaning it. I am very confused on what product I need to use to protect my dashboard from the sun. The same goes for the leather seats, where the creases are forming. I have been using a conditioner (although I am unsure of the exact name) to slow down the crease formation. Should I use the same product for both the dashboard and leather seats (with Lexol Conditioner on top of that)? I have heard of Leatherique Leather Rejuvenator/Prestine Clean, but I am unsure of when I should use that.

https://www.amazon.com/dp/B003LMGDHI/ref=psdc_15718371_t1_B0002UQAM0