Reddit mentions: The best automotive windows

Unless you're powder coating, I'd leave calipers alone. The paint never lasts as long as they're advertised to. Besides, the grey/silver calipers look nice even if left stock.

(relatively) inexpensive mods I've done:

• Window tint; not only looks good, but saves you $$$ over time as your car uses less energy to keep the cabin cool
  
• if you have aero wheels, you can take off the hubcap and cover the center hole and lugnuts with a kit that costs $50 from Tesla.
  
• Might be placebo, but I believe this helps wind noise:
  https://www.amazon.com/AY-Customs-Windshield-Dampening-Reduction/dp/B07N1DXSH5
  RPMTesla makes one too, but costs more and they have less than stellar customer service, according to this sub.
  
• Full chrome delete may be pricey if you pay someone else, but there are inexpensive wrap for just the door handles on amazon, and are easy to install. Your hands will thank you on hot sunny days.
  
• Tesla's paint repair kit. It's a great kit and I've already repaired several rock chips on the side panels, hood and front bumper and they disappeared completely. Follow their video instructions. You'll never consider an expensive wrap after learning how to do this properly.
  
• Not exterior, but /u/kenriko's excellent center console wrap really transforms the fingerprint-magnet interior.

I bought from here : https://www.amazon.com/dp/B0792NCNXS/ref=cm_sw_r_sms_c_api_T4FRBbZ0QY99E

Go to YouTube and look up “decal center hinge” technique, that is what I used to apply these decals. https://i.imgur.com/QsceW2i.jpg I also used a spray bottle with a couple drops of Johnson and Johnson’s baby shampoo to wet down window immediately before application. You’ll need the spray, at a minimum an old credit card (I had previously bought a window tint kit on Amazon for $10) and a razor blade to trim it to fit the window. I took my time and was very patient and both sides took me about 45 minutes total to complete. It was a fun little project.

Looking back, I should have installed it a little higher, cutting the top stripe a little thinner, so if someone gets one, keep that in mind. Also, align the decal to the bottom edge of the window.

I have this installed. It looks super cool. Here is the Amazon link

https://www.amazon.com/Window-Flags-Cherokee-1987-2001-SIDES/dp/B0792NCNXS/ref=asc_df_B0792NCNXS/?tag=hyprod-20&linkCode=df0&hvadid=312026024613&hvpos=1o2&hvnetw=g&hvrand=1689268899239236143&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9051910&hvtargid=pla-567105930466&psc=1

I bought it from Amazon, right here. I would like to buy a new one soon, as this was one of my favorite pieces on my car.

Yea the guy I bought it from never opened them once in ten years haha. the day I opened them to test operation before buying they both broke the plastic connector piece on the latch...easy fix though..I got the same part but paid $8 for both with free shipping

https://www.amazon.com/Dorman-47520-Quarter-Window-Repair/dp/B01D8VJYXQ/ref=sr_1_4?s=automotive&ie=UTF8&qid=1506096265&sr=1-4&keywords=tacoma+side+window+latch

For high speeds you can try something like https://www.amazon.com/gp/product/B07N1DXSH5/
I use it and it helps

Well now this is interesting.

The same company sells the same glass (front drivers side) for the same vehicle but tempered glass. While your link says the laminated glass is compatible with the 2006-2007 extended cab.

BUT looking at Dodge Ram forums it does come with laminated glass from the factory. They should consider switching the wording because people might think the tempered is OEM and the laminated is aftermarket and usually the manufacturer picks a specific type of glass for a reason (sound, safety, reliability, etc.)

Sure. I have a 2006 T1N sprinter 158" wheelbase and these are the windows. also I do have some of the seal tape that CRL sells but I was under the impression that these windows were supposed to have gaskets. almost every single instal video on the internet that I have been able to find either doesnt mention using any kind of sealant at all or mentions a gasket seal on the window itself.
https://www.amazon.com/CRL-2003-Sprinter-Driver-Forward/dp/B000MQ62U4/ref=sr_1_3?keywords=crl+all+glass+look&qid=1554997244&s=automotive&sr=1-3-spell

https://www.amazon.com/CRL-Glass-Sprinter-Sliding-Windows/dp/B001C7WUNK/ref=sr_1_5?keywords=crl+all+glass+look&qid=1554997285&s=automotive&sr=1-5-spell

they should make somethign like this but solid, not that ugly louver shape - https://www.amazon.com/BASENOR-Protector-Anti-Theft-Quarter-Shutters/dp/B07RSKCFRC

Have you tried an aftermarket seal like this: https://www.amazon.com/dp/B07N1DXSH5
$16

I have this product on my P3D. My girlfriend installed something completely different in her SR+. She is an odd cookie but this is another option. Not sure how much it actually would help in a break in attempt but this is the link to watch she got:

Rear Panel Window Theft Protector

SUBARU 2003-2008 Forester Front Left & Right Door Gusset Assembly Set Genuine https://www.amazon.com/dp/B07G4HYY2R/ref=cm_sw_r_cp_api_i_7GenDbHWJ9KSN

Dude. I own an auto glass company and have personally replaced over 1,000 pieces of auto glass. https://www.amazon.com/NAGD-2006-2007-Extended-Laminated-DD10935GTY/dp/B00JG7N0PK

https://www.amazon.com/Window-Lettering-Hyundai-Veloster-Turbo/dp/B00ICVMW6Y/ref=mp_s_a_1_9?keywords=veloster+accessories&qid=1556489758&s=gateway&sr=8-9

The wind noise and the reverse camera delay are my two biggest complaints. Reverse camera delay is software related so that will likely get fixed in the coming months.

I have purchased both this basenor wind reduction kit and this wind guard which seem to help a little but I think most of the noise is coming through the front windshield somehow.

After finding the the part number here, I looked for dimensions to no avail, but found the box size for a windshield subassembly from ebay to be 167.6 x 48.3 x 33 cm.

So, I made a canvas at 1676 x 483, and estimated the size of a windshield in said box, and concluded that it could possibly be done with two. (I took the height, then rotated it as the wiper would)

As seen here: https://i.imgur.com/dkKK6RT.png

Edit: I figured someone might say that the left wiper would be traveling a further distance in the same time, so to that I say it could be stopped after traveling the same distance as the one on the right to the same effect.

CR Laurence VW1033L (driver side 10x33 slider). It was about $220 when I picked it up, check on ebay as well.

The real CR Laurence version clamps directly to van skin, no spacer or anything, no butyl, no extra sealant.

Driver Side Universal Van Bunk Window 33-7/8" x 10-7/8" https://www.amazon.com/dp/B07HXRC28F/ref=cm_sw_r_cp_apa_i_tNVTDbE03PV9Q