Reddit mentions: The best pipe clamp tools
We found 66 Reddit comments discussing the best pipe clamp tools. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 34 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Bessey BPC-H34 3/4-Inch H Style Pipe Clamp, red
- H-Shaped Foot Assembly Stabilizes The Clamp In Two Dimensions Giving Dual-Axis Stability
- Extra High Base Provides Industry Leading Clearance From The Work Surface
- Cast Jaw For Durability
- 2 soft jaw caps are included to prevent damaging materials being clamped
- Zinc plated clutch components, black oxide coated threaded spindle
- H style base prevents clamps from tipping over
- Crank handle clears work surface when opening and closing the jaw on the clamp
- 4 soft jaw caps are included to prevent damaging materials being clamped
- Durable powder coat finish
- Zinc plated clutch components, black oxide coated threaded spindle
Features:
Specs:
Color | red/black |
Height | 5 Inches |
Length | 8.5 Inches |
Number of items | 1 |
Size | Pack of 1 |
Weight | 1.10231131 Pounds |
Width | 2.5 Inches |
2. Bessey BPC-H12 1/2-Inch H Style Pipe Clamps
- Mpn: BPC-H12
- Country of manufacture: China
- Manufacturer: Bessey
- H style base prevents clamps from tipping over
- Crank handle clears work surface when opening and closing the jaw on the clamp
- 4 soft jaw caps are included to prevent damaging materials being clamped
- Durable powder coat finish
- Zinc plated clutch components, black oxide coated threaded spindle
Features:
Specs:
Color | Red |
Height | 4.5 Inches |
Length | 8 Inches |
Number of items | 1 |
Size | Pack of 1 |
Weight | 2 Pounds |
Width | 2 Inches |
3. iCrimp Ratchet PEX Cinch Tool with Removing function for 3/8 to 1-inch Stainless Steel Clamps with 20PCS 1/2-inch and 10PCS 3/4-inch PEX Clamps and Pex Pipe Cutter- All in One
- 「UNIVERSAL」This tool meets ASTM 2098 standard will work with stainless steel clamps from any manufacturer to make PEX connections from 3/8-inch to 1-inch. It can also be used to cinch single ear hose clamp,as long as the ear’s length&width is within the opening range of the jaws.
- 「INNOVATIVE」New design makes it be a multi-function tool which can cinch clamps and remove the clamps from pipe to allow re-using the pipe fittings,cost-effective and convenient.
- 「DURABLE」The cinch&remove tool is constructed of durable high-quality steel with forging process to ensure integrated mechanical property and long service life,and inside of the jaw is processed with Wire EDM Cutting to ensure the precision.
- 「EASY」It’s easy to switch cinch and remove function.And the ratcheting design and self-release mechanism makes the cinch effortless.The tool is factory-adjusted with no requirement for calibration tool.
- 「ALL-IN-ONE」This is a All-in-one kit for pex pipe installation, it includes 1pc of cinch&remove tool,1pc of Pex cutter,20pcs of 1/2-inch clamps and 10pcs of 3/4-inch clamps.
Features:
Specs:
Color | blue&red |
Height | 0.79 Inches |
Length | 11.02 Inches |
Size | Tool Kit |
Weight | 2.4 Pounds |
Width | 3.74 Inches |
4. Snap Clamp 1/2 Inch X 4 Inches Wide For 1/2 PVC Pipe White 10 per Bag
Great formaking cold frames, Greenhouse, shelters, row covers.Compatible with any type of pipe, including PVCBetter Gripping with ABS and does not decay film.Use to hold all kinds of sheet material.
Specs:
Color | White |
5. SharkBite-Oetiker UC953CP100 1/2 inch PEX Barb Clamp Rings, 100-Pack, Stainless Steel
- EASY INSTALLATION: Slide the 1/2 in. clamp ring over the pipe, push the pipe onto the fitting and squeeze with your clamp tool
- COMPATIBILITY: Use with brass or poly PEX crimp fittings, PEX or PE-RT pipe and clamp tool
- QUALITY: SharkBite's quality and performance is field-proven and is the only push-to-connect brand than can ensure a clean, leak-free connection
- CERTIFIED: Meet ASTM F2098 requirements
- PREFERRED BY THE PRO: All SharkBite products meet the same standards for commercial and residential plumbing applications
Features:
Specs:
Color | Stainless Steel |
Height | 9 Inches |
Length | 1 Inches |
Number of items | 100 |
Size | 100-Pack, |
Weight | 0.9 Pounds |
Width | 6.38 Inches |
6. Denali 3/4-Inch Pipe Clamp Fixture, 12-pack
- Scorch Torch Double Jet Flame Torch Cigarette Cigar Lighter w/ Keychain and Strap
- Size: 0.75" x 0.92" x 3.35" - Weight: 3.6 oz w/ Retail Box
- Safe & Easy to Use - Adjustable Flame Control - Butane Refillable
- Automatic Open Safety Cap (Attached) - Keychain w/ 24" Carry Strap
- Bonus Items Included: FREE Scorch Torch?? Velvet Gift Pouch, 1 Year Hassle-Free Manufacturer's Warranty
Features:
Specs:
Height | 7.09 Inches |
Length | 23.62 Inches |
Width | 18.9 Inches |
7. Plumb Pak Keeney 300K x 1.25-in. Brass P-Trap, Polished Chrome
20 Gauge brass P-trap1. 25-in. inlet and 1. 25-in. outletComes with a matching flangeIncludes all brass nuts and washers for installationLimitedP-trapInlet: 1-1/4-Inch outlet: 1-1/4-InchWith flangeChrome plated 20-Gauge brass tubingFor lavatory sinks
Specs:
Color | Polished Chrome |
Height | 8.88 Inches |
Length | 5.75 Inches |
Number of items | 1 |
Weight | 0.44 Pounds |
Width | 2.25 Inches |
8. PONY 52 Pipe Clamp, Fixture for 1/2-Inch Black Pipe
- Works with any length of 1/2 in. black or galvanized threaded pipe
- Includes head, tail stop, and coil spring stop
- Durable cast iron body
- Features multiple-disk-clutch
- Clamping faces are 1-1/2 in. by 1-1/2 in.
- Easy to assemble
- Easy to use
- Perfect for woodwork, repairs, and professional uses
Features:
Specs:
Height | 6 Inches |
Length | 5.25 Inches |
Number of items | 1 |
Size | Pack 1 |
Weight | 1.44 Pounds |
Width | 1.75 Inches |
9. IRWIN QUICK-GRIP Pipe Clamp, 3/4-Inch (224134)
Innovative clutch system eliminates the need for threaded pipeLarge feet offer more stability and clearance between handle and worktopErgonomic handle offers easier clamping and reduced hand fatigueLarge clutch plates release easily for increased durability and dependabilityBuilt to handle 3/4" pipe...
Specs:
Color | Multi |
Height | 2.3 Inches |
Length | 7.9 Inches |
Number of items | 1 |
Size | 3/4 Inch |
Weight | 1.6 Pounds |
Width | 9.7 Inches |
10. Apollo PEX 69PTKG1096 3/8-inch - 1-inch Stainless Steel Pinch Clamp Tool
- Use with Oetiker pex pinch clamps 3/8 in., 1/2 in., 3/4 in., and 1 in.
- Also for use on Apollo pex and Murray pex pinch clamps 3/8 in. - 3/4 in.
- Not for use with Zurn Qickclamp crimp rings
- Meets ASTM F-1807n What's In The Box:Conbraco 69PTKG1096 Pex Quick Pinch Clamp Tool
Features:
Specs:
Color | Black, yellow |
Height | 6.5 Inches |
Length | 5.5 Inches |
Number of items | 1 |
Weight | 1.5 Pounds |
Width | 15.25 Inches |
11. Seloky 130Pcs 7-21mm 304 Stainless Steel Cinch Clamp Rings, Single Ear Stepless Hose Clamps Assortment Kit, Crimp Pinch Fitting Tools -Packed in Plastic Box
- ★【Corrosion-Resistant】 High precision single ear stepless hose clamps 304 stainless steel, Corrosion-Resistant , will not rust for long-term use
- ★【Increase Clamp Force】 Hose clamps used to seal various types of hoses, pincers can increase clamp force, designed for repairing pipes & plumbing systems
- ★【Edge Polished Smooth】 Cochlear design ensures continuous clamping during temperature changes or machine vibrations, edge polished smooth, avoid damage to the hose.perfect kit for the DIY home-owner or the professional looking to get started with plumbing bundle
- ★【360 ° Stepless Design】 There is no protrusion and gap in the inner, narrowband design providing a more concentrated sealing pressure
- ★【Storage box】 7-21mm 7 Kind Of Size 130pcs Total In A Clear Box, Easy To Store
Features:
Specs:
Size | 7 Size 130 Pieces |
12. Gardner Bender PPC-1600UVB Plastic Cable Clamp, 1 Inch., Construction / Maintenance & Assembly-line Operations, Holds Wire / Tubing / Cable & Harnesses, 4 Pk., UV Resistant Black
UVB Cable ClampSuperior quality at an affordable priceGardner Bender branded products and professional equipment have been a mainstay with electrical contractors
Specs:
Height | 5.5 Inches |
Length | 1 Inches |
Number of items | 1 |
Width | 3.75 Inches |
13. Cushioned Pipe Clamp, Tube Size 1 In
- Price For: Each Includes: Welded 3/8" Cap Nut Bolt Size (In.): 3/8-16 Standards: Conforms with Manufacturers Standardization Society (MSS) SP-58 And SP-69 (Type 12), Fire rating according to DIN to EN13501-1:E Metal Detectable: Yes Description/Special Features: With EPDM Cushion; Recommended For Suspension Of Stationary Non-Insulated Pipe Lines Material: Electro-Galvanized Steel, EPDM-SBR Rubber
- Thread Size (In.): 3/8 Item: Pipe Clamp Type: Cushioned Rod Size: 3/8" Pipe Size (In.): 3/4 Tube Size (In.): 1 Max. Load (Lb.): 180 Country of Origin (subject to change): China
Features:
Specs:
Height | 1.1 Inches |
Length | 3 Inches |
Weight | 0.12 Pounds |
Width | 2.5 Inches |
14. T-Clamp Ps 1-3/8 X 1-3/8 In Rp
- Upc: 754761762560
- Weight: 0.500 lbs
Features:
Specs:
Height | 10 Inches |
Length | 10 Inches |
Number of items | 1 |
Width | 10 Inches |
15. LDR 510 3210 Galvanized Pipe Strap, 1/2-Inch
- For 1/2-Inch pipe
- Two hole galvanized pipe strap
- Holds securely
- Prevents vibrations
- Limited lifetime warranty
Features:
Specs:
Color | Brown |
Height | 3.75 Inches |
Length | 5.5 Inches |
Number of items | 1 |
Size | 0.5 Inch |
Width | 0.75 Inches |
16. LOKMAN 20 Pack 1/4 Inch Stainless Steel Cable Clamp, Rubber Cushioned Insulated Clamp, Metal Clamp, Tube Holder for Tube, Pipe or Wire Cord Installation
HIGH QUALITY- Premium 304 Stainless steel cable clamps which rubber cushioned. Salt resistant, anti rust, anti-corrosion, waterproof, oil-proof. These features make the clamps very sturdy and strong and can be worked lasted for years. The quality rubber insulation on the clamps held up flawlessly. I...
Specs:
Height | 3 Inches |
Length | 3 Inches |
Size | 1/4 Inch |
Weight | 0.04 Pounds |
Width | 0.4 Inches |
17. JWGJW PEX Clamp Cinch Tool Crimping Tool Crimper for Stainless Steel Clamps from 3/8"to 1" with 1/2" 22PCS and 3/4" 10PCS PEX Clamps (002)
- Ratchet and self-releasing mechanism ensure a completed crimp
- The cinch&remove tool is constructedof durable high-quality steel with forging process to ensure integrated mechanical property and long service life
- It’s easy to switch cinch and remove function.And the ratchet design and self-release mechanism makes the cinch easy.The tool is factory-adjusted with no requirement for calibration tool
- Work with Stainless Steel Clamps of sizes 3/8", 1/2", 5/8", 3/4" and 1"
- This is a All-in-one kit for pex pipe installation,includes 1pc of cinch&remove tool,22pcs of 1/2” clamps and 10pcs of 3/4” clamps
Features:
Specs:
Height | 0.4 Inches |
Length | 11 Inches |
Weight | 1.46 Pounds |
Width | 3.15 Inches |
18. PONY 50 Pipe Clamp, Fixture for 3/4-Inch Black Pipe
The product is 3/4" Pony Bar ClampEasy to useThe product is manufactured in ChinaMounts on any length 3/4” black pipe with both ends threaded (pipe not furnished)Clamping capacity only limited by length of pipe usedMultiple-Disc-Clutch design which allows a secure hold at any point along the pipeC...
Specs:
Color | Black |
Height | 8.5 Inches |
Length | 5.25 Inches |
Number of items | 1 |
Size | Medium |
Weight | 2.45 Pounds |
Width | 2 Inches |
19. Shop Fox D4441 Clamp for 3/4" Pipe
- Powerful clamping torque with double-handle
- Accepts 3/4" pipe
- Solid construction for years of dependable service
- Pipe clamp for 3/4-Inch pipe
Features:
Specs:
Height | 2.5 Inches |
Length | 7.5 Inches |
Number of items | 1 |
Weight | 2.6 Pounds |
Width | 4.75 Inches |
20. CORNAT T595510 9mm 10m Spiral Pipe Cleaning
CORNATHigh QualityPipe cleaning spiral 9mm 10m
Specs:
Release date | October 2014 |
Size | Ø 9 mm, 10 m |
Weight | 0.9479877266 Pounds |
🎓 Reddit experts on pipe clamp tools
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where pipe clamp tools are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
I honestly don't have any resources, mostly because PEX is so damn simple that there's really nothing to it. You just need a PEX tubing cutter (for making perfect cuts and not having to clean them up) and a PEX ring tool - I prefer the "cinch" (aka "pinch clamp") style, because the rings can be removed easily if you mess up and need to re-do a connection, and because you don't need to mess with checking each of your connections with a gauge to make sure it was clamped tight enough - you just squeeze the tool together until it unlatches and you're done. Here is a kit with both the tools you need and a handful of the rings.
Then, you'll just need a ton more rings (I use these 3/4" and these 1/2" ones, get WAY more than you think you'll need just in case); you'll need the PEX tubing, get that at the hardware store because it costs a little less than Amazon and they sell the straight pieces which are easier to work with if you are doing short runs (under 5 to 10 feet); and you'll need the appropriate fittings. The fittings are super simple to understand, just grab what you think you'll need and then grab a few more extras (remember you can just remove the cinch clamp and re-use the fittings as much as you want); I recommend getting the plastic fittings when you are getting started because they are much cheaper and they have a built-in "spacer" that helps you position the cinch ring exactly where it goes. Honestly I don't re-use the plastic ones - I just toss them as they are so cheap - but the brass fittings are easy to reuse (but they do cost more). Get some PEX hangers to hold the tubing up securely, I use these ones (just pick the size you need).
To make a PEX connection, you just use your cutting tool (which cuts like butter, it's shockingly easy to cut) to make a straight cut; put a ring over the tube, then push the fitting into the tube as far as it will go. Slide the ring so it's 1/8 to 1/4" from the end of the tube (or, right up to the "spacer" on plastic fitting), then open your cinch tool, put the jaws over the "ear" that sticks out of the ring, and squeeze together until the ratcheting mechanism unlocks, which means the ring is done. It helps to have someone hold the fitting for you while you position the ring and squeeze the tool, especially on 3/4", until you get the hang of it.
If you have any questions you can DM me. Here is a picture of my completed Viega Manabloc setup, which has 3/4" PEX coming in the top from the cold water supply and hot water heater, and then has individual valves for 1/2" PEX runs that go directly to each of the fixtures in the house. By doing it this way, I used a LOT more PEX tubing, but have far LESS fittings so it went quick and gives me a lot of flexibility - now, I can turn individual fixtures off and on from the manifold. Very happy with the setup.
If I was starting from scratch I'd first get:
https://www.amazon.com/dp/B01LW80Y0J/ref=biss_dp_t_asn
At $9.8 a clamp for 330lb pressure quick clamps they're great. Not quite as nice as the heavy duty Irwins because each squeeze doesn't move them as much but for the price I'd go with the Yost.
https://www.amazon.com/Yost-M7WW-Rapid-Acting-Working/dp/B00SIQ1DDG/ref=pd_sim_328_2?_encoding=UTF8&refRID=BKJ5FP839P8N1FH21F8T&th=1
That vise is a pretty nice deal right now too.
Probably 2 packs of these but they'll take forever to arrive:
https://www.amazon.com/Jet-70460-2-Parallel-Clamp-Pack/dp/B000UBIXD0/ref=pd_sim_328_1?_encoding=UTF8&psc=1&refRID=BKJ5FP839P8N1FH21F8T
I'd get maybe 8 of these, and pipe from the home center:
https://www.amazon.com/Bessey-BPC-H34-4-Inch-Style-Clamp/dp/B0012YNJRO/ref=pd_sim_469_10?_encoding=UTF8&psc=1&refRID=ECFV96CT5EFKCBM4BQW1
Go to the home center for the current deals on the Bessey F style bar clamps, or HF specials, I don't think I can live with less than 8 of those.
And I'd say 6 of these:
https://www.amazon.com/dp/B0713YHP6Q/ref=biss_dp_t_asn
Based on current pricing I'd go with the Yost, but my personal favorite are the Jets. After getting the hang of the Yosts I honestly like them more than K body Revos from Bessey because they tighten faster and harder. However they have a bit of slop and you have to kinda nudge them to get them to bite, which was frustrating the first time I used them.
And there I've just spent $800 for you :)
Depending on what you make, corner clamps, miter clamps, twin screw wood clamps, dovetail/fence/drill press clamps, toggle clamps for jigs, track clamps for track saw, C clamps, pocket hole clamps etc.
Edit: pricing this out made me notice I've spent well over $1k on clamps... That list is probably barely half my clamps not even...
I don't have pics of my IBC fish tank, but I wrapped something like this around it.
White side out to reflect most of the heat/light away, black side in so no light makes it through to any potential algae. I even built a pvc frame with a hinge at one end, then wrapped that with the white/black film and clipped it to the frame with these. It made a pretty nice lid to my fish tank IBC.
Remember, fish don't need much light. They actually prefer shade, it makes them feel safe and hidden. Some ambient light still slightly lights up the tank in my setup which is just about perfect for them.
If you can verify that there's pressure behind those caps, i.e. that they're plumbed into the main system but sealed, then it will be very easy to finish. Any plumber could do it in 45 minutes max.
The drain too, just requires a fitting glued on to accept the chrome or plastic P-trap from the sink. That's even easier...like 10 minutes.
If you're wanting to get into this a little, go ahead and do this:
Buy a drain trap, and a suitable adapter for your drain pipe (probably 1.5" PVC, but possibly 2". Can't tell from the photo. Measure the outside, and tell the home labyrinth attendant, he'll get you the right one.). That'll get your drain attached, as long as there's one in the sink. If not, you need a sink drain to attach to as well.
Then get yourself this sink kit. This is what lets you connect your hot and cold supply lines to the faucet. No soldering required, just a clean end, push on, and you're done.
If you want to be sure this is hooked up right: turn off the water to the whole house and relieve pressure by turning on a faucet that runs. Make sure no other faucets run at all. Take a hacksaw and cut off the cap, staying as square as you can. Have a bucket ready, and have someone else SLOWLY turn on the water. If you get water out of both pipes, you're golden, and you're ready to proceed with the sink kit above. If not, slap a couple of these end caps back on the pipes and call a plumber...it needs more work.
In theory it should work fine. My only concern with a clamp design such as that is being able to support the table, and still being able to use the clamps. Generally you would want to build something like that on a flat surface and keep it there while it's clamped up. With a clamp that goes both over and under you won't be able to keep the table flat. I guess your only method of supporting the whole thing would be on a few sawhorses, which would promote it to sag and not be perfectly flat.
Have you considered using a clamp like this style? You would only need to get some 1/2" black pipe. A 10' section from home depot is only 12 bucks, and that's enough to make 2 clamps out of it is you chop it in half.. So for 38 dollars you can make 2 clamps. Plus, if you are able to get threaded rod from the HVAC guy, can you get black pipe too and save yourself some money...
Craftsman Table Saw Model # $150
Shop Fox model #G8826 fence system $275
Freud P410 Premier Fusion 10-Inch 40 Tooth Hi-ATB General Purpose Saw Blade $80
Wilton 15” drill press $100
Parks 12” planer $600 This requires a little road trip
Atlas 6” jointer $150 Model #
Delta 10” bandsaw, Powerkraft radial arm saw and Rockwell contractor table saw $200
I would resell one of the tablesaws Just pick the nicest one and sell the other.
Oneway Multi Gauge $97 This is for setting the jointer perfectly and the dial indicator can be removed to make planer setting jig as described by Bob Vaughan (see youtube) or fine woodworking 107.
Angle block set for machine setup $30
Bessey Bar Clamps $14x3 plus maybe $10x3 for bars Say $75 total
Stanley sweetheart chisel set of 4 $80
This leaves $243 left for misc things like drill bits, planer/jointer knives or sharpening F style clamps a cordless drill, random orbit sander, sand paper ect.
Well, I misspoke on the price. It's actually $13.30/each for 10' 1/2" iron pipe. Throw in the Bessey BPC-H12 clamps, and the cost then goes up to $24.02/clamp. Now, $24 for a 10' bar clamp is a fantastic deal. I don't really need 10' clamps; I need 5' clamps. So really I'm looking at $34.74/2 clamps ($17.37/clamp)--still a great deal. The thing is, I need about 8 clamps, or $138.96. This is where I have a problem with the price -- it's not that I don't think $138.96 is fantastic for 8 5' bar clamps, especially when Amazon sells 5' clamps for $37.36/clamp. But, if I can find pipes for less than $13.30 for 10' (or $6.65/5'), then why not try?
TL;DR: You're right, $13.30 is inexpensive, but I want it to be even more inexpensive. :)
Yes, those are pipe clamps:
https://www.amazon.com/Bessey-BPC-H34-4-Inch-Style-Clamp/dp/B0012YNJRO/
Best option BY FAR to get a long clamp on the cheap. You can also put out a tremendous amount of force with them. Great addition to any shop.
I'm in a similar situation, just bought a dw735x and I am hoping to make a cutting board by Mother's Day. Like you I didn't have enough clamps. I ran across a pretty good deal on amazon and now I have plenty of clamps for a cutting board. Just have to pick up some pipe from a hardware store.
Here's the link http://www.amazon.com/gp/aw/d/B0012YNJRO/ref=mp_s_a_1_1?qid=1398484165&sr=8-1&pi=SX200_QL40
Wow congrats on doing an entire tabletop lamination with just the Irwin grippy clamps. If you decide to do more of this, a little set of pipe clamps will be a nice upgrade and not too expensive.
IRWIN QUICK-GRIP 3/4" Pipe Clamp, 224134 https://www.amazon.com/dp/B0000CCXVO/ref=cm_sw_r_cp_api_1WNTAbR4GW7SH
Great value for money.
I prefer the style with the stand myself. Like these bessey's. Easier to use on large glue up when you can set the clamps up on a flat surface.
Plumber for ten years now. Go with pex you will not regret it. In fact just forget that pvc(and cpvc) water lines exist(as a new or replacement option) and you will be better for it. Pex is slightly more flexible than pvc and not brittle like pvc. It is far stiffer than clear vinyl hose and will last far longer. Skip the sharkbites (they have to be secured from movement and vibration) and buy one of the stainless steel cinch ring tools(like this, also available at lowes)
Worm clamps are a fine substitute. If you go stepless, I'd buy a set that is like this one. They prove to be valuable to have on hand.
I used a Cable Zipper and ran the speakers, monitor, keyboard and mouse cables through it. After that got some Industrial Strength Velcro from Home Depot along with a couple of 1" Cable Clamps and started mounting everything to the top of the desk. I also nailed in a few thumb tacks just for that extra security but you don't really need them.
Here's a better picture of it directly below the desk. http://imgur.com/NfUdjCL
If you need a super quick fix - i would just cap off the red one (from your pick it looks like the red one came disconnected. However i would simply fix the whole thing. Also, if your faucet has a single handle - water could leak from cold side to hot side.
The issue is figuring out if your faucet itself is done for. They are often made out of plastic and if the plastic cracked, you cannot really fix it and need to replace the whole faucet.
​
Pex is REALLY easy to work with. You need a ring cincher, rings, and some fittings.
If the sink is ok, i would guess from this limited photo that does not actually let me see the hot side threaded connection - that you need a 90 degree female threaded fitting.
​
Example of cinch rings (i prefer them over crimp ring)
https://www.amazon.com/dp/B01GU4YXA2
Cinch tool: here is an all in one kit
https://www.amazon.com/iCrimp-Cinch-Tool-Removing-function/dp/B07CCH5JWG
90 degree elbow (this price seems high )
https://www.amazon.com/SharkBite-UC532LFA-2-Inch-Swivel-Packaging/dp/B00A8HSWIC
​
If you have more photos or more questions let me know. I have totally redone all pex plumbing and faucets in a camper, as well as service other pex in other campers and my house.
​
Edit to add:
​
If this was during cold winter storage - i would suspect cracked plastic. Pex itself normally does not split, but plastic fittings (be it the elbows in the pex- faucets etc). I have come to expect the valve in my toilet to freeze each time. This winter instead of just blowing out the water lines, i actually filled with rv antifreeze and it worked! nothing was damaged. Last year i had to replace a toilet valve and the little filter window thingy on the water pump.
​
I would also suspect that the faucet is cracked even if you fix the connection, there is more cracked inside and it might leak. You can upgrade to a residential fautcet. Yes it adds weight, but might be worth it.
​
As i have plastic elbows etc break, i replace them with metal. It lasts longer.
Not sure the exact part name, but you may be able to hack together a solution with a pipe clamp and some hardware. Something like this or this.
Ponys. Amazon sometimes has open box "used" ones for cheaper. Best bang for the buck. Just get different lengths of pipe and they are very versatile.
I like pipe clamps because they are versatile, you can buy different size pipes for different projects instead of having to buy new big long clamps. like these... and then you just get whatever size pipes you want. they also sell 3/4" versions if you want something beefier.
https://www.amazon.com/Bessey-BPC-H12-2-Inch-Style-Clamps/dp/B0012YOC0W/ref=sr_1_2?ie=UTF8&qid=1520457164&sr=8-2&keywords=bessey+pipe+clamp&dpID=4124AZGEqwL&preST=_SY300_QL70_&dpSrc=srch
My beds are the same size as yours. I mounted PVC pipes on the sides of the beds. Then I found these on Amazon, they are fantastic!
https://www.amazon.com/gp/product/B0050B0N06/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
I thought they were a bit long so I cut them in half.
I use a simpler design that is barely noticeable and requires very few posts. I create frames as you did, but using all metal. Using 1-3/8" pipe I use the following to create corners (this is not the vendor I've use, but Amazon had the photos):
https://www.amazon.com/midwest-technologies-328623b-Aluminum-Bolts/dp/B00E5JDNGU/
Then this to create the center post for stability:
https://www.amazon.com/T-Clamp-Ps-1-3-Rp/dp/B00331WLLE
Roll out the fence and use the wire to tie it to the frame. Once the frames are done then use the following to connect them to each other:
https://www.amazon.com/Chain-Fence-PANEL-CLAMPS-KENNEL/dp/B0113BD43E
You could maybe use pipe straps but they'd need to be pretty tight to not slide.
http://www.amazon.com/LDR-510-3210-Two-Hole-Galvanized/dp/B002KXWQ0M/ref=sr_1_9?ie=UTF8&qid=1368410252&sr=8-9&keywords=pipe+straps
Thanks for the heads up! Grabbed 4!
Also not bad:
Bessey BPC-H12 1/2-Inch H Style Pipe Clam https://www.amazon.com/dp/B0012YOC0W/ref=cm_sw_r_cp_api_rknNybZJP73WT
Side note: you should probably ditch the conduit straps in favor of something rubberized. That system will have a tiny amount of vibration which (eventually) will be an issue.
Something like this is preferred:
https://www.amazon.com/LOKMAN-Stainless-Cushioned-Insulated-Installation/dp/B01IT43WVM/ref=mp_s_a_1_4?keywords=cable+clamp+1%2F4&qid=1564705840&s=gateway&sprefix=cable+clamp+&sr=8-4
Personally, I'd go with Bessey. The 3/4" fixtures are $12 each: https://smile.amazon.com/Bessey-BPC-H34-4-Inch-Style-Clamp/dp/B0012YNJRO/
Then head over to the local Home Depot or Lowe's and buy 10' sections of 3/4" black pipe. You can have a store employee cut the pipe and thread it for you. I'd buy two 10' pipes and have each of them cut into one 36" piece and two 24" pieces. Thread both ends, that way you can use a coupler if needed to extend the pipes. The 10' pipes should cost around $25 each.
You won't quite get to 10 clamps at a budget of $150, but you'll get pretty close!
If you want a lot of pipe clamps for a decent price Amazon sells this 12 pack of fixtures for ~$95.
http://www.amazon.com/dp/B000NDHN90
They seem just as nice as the few Jorgenson's that I also have. It's a pipe clamp...it's not rocket science.
Look for a lumber yard around your area. Purchase plain-sawn lumber and take it to a milling company to have it thickness planed. Otherwise, check the 'materials' section of craigslist or just go to Home Depot.
If you want to make a dining table you will need clamps for the table top, unless you breadboard the ends and don't glue the long edges together. I personally like pipe clamps and buying kits and pipe at a hardware store is a fairly inexpensive way to get a bunch of pipe clamps for not much money.
Every tool I own I purchased off craigslist, or a yard sale.
That style of pex connector needs to be destroyed to free the pipe. You could likely reuse the copper elbow section if you don't damage it when removing the pex ring.
The ring is likely copper that can be easily sawn with a hacksaw. You will find it easier if you cut the pex just before the copper fitting. However replacing the copper to the pex, with any style of pex crimp will require a special tool.
I recommend this style because it's only a single tool and it's often affordable. You can try to crimp with pliers but results will vary based on technique.
The copper pieces are a pex by ½" copper into a ½" street 90 into a ½ by I'm guessing ⅜ reduced coupler. Not sure how you had a dishwasher line on the other side of that though.
Pipe clamps. They’re relatively inexpensive. They’re just the ends and you put them on a piece of pipe. You buy the pipe separately so the clamp can any length you want it. Typically black iron or galvanized pipe, 3/4” - 1” depending on the size of the pipe clamp. The nice thing about pipe clamps is you can get one set and then just multiple lengths of pipe and swap them out depending on how long you need them. The should have them at most big box hardware stores. Very handy, especially when you need long lengths.
Here’s an example
Or better buy a plunger for sinks and such and a "cleaning spiral" for the rest. cleaning spiral is the direct translation from the german word, I just simply don't know the english. Maybe someone does.
Weekend woodworker here. This looks reparable, assuming you can get a few clamps on either side of the piece to hold it together while you glue it.
For glue, use Franklin International 1414 Titebond III Ultimate.
For clamps, use some Pipe-style clamps, like these. You'll need a clamp for every 6" or so of the crack.
If you have an air compressor or a can of air, like you use for cleaning computer parts, blow out anything that is in the crack. Probably will have some dust and small wood particles you want out before you glue it down.
Fill it with glue, clamp it down, and let it set for at least 24 hours and don't even look at it. Then, release your clamps and it should hold tight.
Bessey BPC-H34 3/4-Inch H Style Pipe Clamp https://www.amazon.com/dp/B0012YNJRO/ref=cm_sw_r_cp_apa_i_JsUvCbCP00DBD
I quite like these.
Pipe's the cheap part of the system. Buy pipe to match the clamp ends, not vice versa.
I've had good luck with this 12-pack of import clamps. They're not quite as good of quality as Jorgensons, but the price is right.
Looks like these. Naturally, you have to buy the pipe locally.
Pipe clamps are pretty cheap, very rigid, and can be made to any length.
https://www.amazon.com/gp/product/B0012YNJRO/ref=s9_acsd_top_hd_bw_b2Jtq_c_x_1_w/141-2934950-2682627?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=merchandised-search-3&pf_rd_r=JXFFTJNXZ338MM76V4BX&pf_rd_t=101&pf_rd_p=45e253bc-836e-5ed1-817f-396a339d6e64&pf_rd_i=553154
Seems like they're more expensive than pipe clamps:
http://www.amazon.com/Jorgensen-50-4-Inch-Clamp-Fixture/dp/B0000224C9/ref=sr_1_7?s=power-hand-tools&ie=UTF8&qid=1375668866&sr=1-7
Obviously the pipe will still cost more than a 2x4, but those look kind of unruly.
Claaaamps. Moar Clamps!
https://www.amazon.com/Bessey-BPC-H34-4-Inch-Style-Clamp/dp/B0012YNJRO/ref=sr_1_5?keywords=bar+clamp&qid=1551187967&s=gateway&sr=8-5
Wait. You can totally do pex with shark bite or a 25 dollar crimper.
Pex Cinch Clamp Fastening tool https://www.amazon.com/dp/B003IJ0USC/ref=cm_sw_r_cp_awd_cxx9wb9TRH1SJ
To do crimps, you'd need a bag of crimps, a way to cut(many simple ways, or a ten dollar cutter) and the tool above.
The Bessey pipe clamps have been at that price for a while now, and they have little feet that raise the work off the floor/table/whatever the clamp is sitting on.
Home Depot
Amazon
And the Irwin version at Lowes is a little cheaper.
Bessey BPC-H34 3/4-Inch H Style Pipe Clamp https://www.amazon.com/dp/B0012YNJRO/ref=cm_sw_r_cp_api_tSy0xbFR9STT9
$15.00
10ft- 3/4in black pipe- $13.99 at Home Depot
That $30 for a 10ft clamp
Where are you people buying any pipe clamp for less than $20.00? Heads are $17 : http://www.amazon.com/Bessey-BPC-34-4-Inch-Style-Clamp/dp/B0012YNJRO and then you have to buy the pipe. Black iron pipe is waaayyy more than 5 bucks.
I just started as well using only hand tools. Hopefully this helps in some way. Don't hate me if it doesn't.
So far here is what I've collected:
Note - I have no idea if that knife sharpener is correct to use with the chisels and plane. I'm only using the fine stone and it seems to work, but I have no idea what I'm doing in that department.
This seems to cover the basics for me. I'm about halfway through a desk project and struggling, but I think that's user error more than the tools. More clamps and a better workspace would work wonders.
Yeah, I dont mind their pipeclamps. I've purchased a few HF ones, had a couple fall apart, but the rest have lasted years actually.
That said, you can get bessey pipe clamps off amazon for almost the same cost. Those aluminum parallel clamps have had a 100% fail rate for me, so I'm done buying/recommending them.
https://www.amazon.com/Bessey-BPC-H34-4-Inch-Style-Clamp/dp/B0012YNJRO/ref=sr_1_1?ie=UTF8&qid=1522002867&sr=8-1&keywords=bessie+pipe+clamp
No, sorry, it is me who misunderstood.
https://www.amazon.com/gp/product/B0012YNJRO/ref=s9_acsd_top_hd_bw_b2Jtq_c_x_1_w/141-1319240-2436003?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=merchandised-search-3&pf_rd_r=BA48TMSZW2Q5940ACE1F&pf_rd_t=101&pf_rd_p=45e253bc-836e-5ed1-817f-396a339d6e64&pf_rd_i=553154