Reddit mentions: The best powersports grips

God I hope this formats correctly - I am a neophyte.

Exhaust - http://www.ixilusa.com/ixil-l3xb-black-hyperlow-xl-full-exhaust-yamaha-mt-07-2014-2015/

Super deep and loud sound - videos online don't do it justice, its unbelievably loud when the baffles are out. Had to have the cat cut out of it. Be aware they have a cat in the V section before the end of the pipe.

Removed the snorkel covering the airbox - I was told its basically blocks airflow.

ECU Flash / Dyno by 2wheelDynoWorks - https://2wheeldynoworks.com/shop/ecu-flashing-service/15-17-yamaha-fz07-mail-in-ecu-flashing-service/

Nels himself worked on my bike - super stoked (shout out to Nate too) They have the best customer service.

Active Tune - https://2wheeldynoworks.com/shop/ecu-flashing-service/yamaha-activetune-afr-closed-loop-self-tuning-ecu-kit-2/

Tune as you go

Bike side harness - https://2wheeldynoworks.com/shop/ecu-flashing-service/ftlink-v1-1-6-pin-bike-side-harnesses/

For tuning later

Windscreen - https://www.revzilla.com/motorcycle/puig-touring-naked-new-generation-windscreen-yamaha-mt-07-2018

I got light smoke, I think it goes better with the bike and pushes wind over my shoulders even at 80+ mph

Protection - https://tstindustries.com/Womet-Tech-Total-Crash-Protection-Pack-for-Yamaha-FZ-07-MT-07-2015.html

Basically got everything from this except the bar ends

Bar Ends - https://motostarz.com/collections/mt-07-2018/products/rhinomoto-barends-mirror-mounts-for-yamaha-fz-mt-models

Super easy to replace mirrors etc with these - and they add protection

Throttle tube - https://www.amazon.com/gp/product/B005C59NO2/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

90 to 60 degree conversion - its amazing for the price

Dash Screen Protector - https://www.amazon.com/gp/product/B078SMP4ND/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Mirror stem deletes - https://www.amazon.com/gp/product/B07BN8QGPV/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

Current Mirrors - https://www.amazon.com/gp/product/B01N6GB7DZ/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

Mirrors in photo - https://www.amazon.com/gp/product/B003RESHVU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

I like the CRG Mirrors but they get bumped and are hard to readjust - the cheap ebay/amazon mirrors work great

Headlight replacement - https://www.amazon.com/gp/product/B01H6NZ5QW/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

Signal replacement LED bulbs - https://www.amazon.com/gp/product/B06XK4PL33/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

Super bright replacements for stock bulbs - used the original housings, they plug right in

Running light LED replacements - https://www.amazon.com/gp/product/B00JRE38EA/ref=oh_aui_detailpage_o01_s01?ie=UTF8&psc=1

For inside the headlight housing

Tail Tidy - https://www.amazon.com/gp/product/B01BH5YGOM/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

Flasher Relay for LEDs - https://www.amazon.com/gp/product/B00RM26LXO/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

Levers - https://www.ebay.com/itm/CNC-Brake-Clutch-Yamaha-MT-07-FZ-07-2014-2018-Adjustable-Engrave-Long-Lever/123350737715?_trkparms=aid%3D555018%26algo%3DPL.SIM%26ao%3D1%26asc%3D20131003132420%26meid%3D17a37c1b2d204ffcba65903d19a97b4a%26pid%3D100005%26rk%3D4%26rkt%3D12%26sd%3D122997203335%26itm%3D123350737715&_trksid=p2047675.c100005.m1851

Passenger peg deletes - https://www.ebay.com/itm/for-YAMAHA-MT07-FZ07-Footrest-Cover-Passenger-Footpeg-Removal-Delete-Kit-2014/253869999740?hash=item3b1bd4c67c:g:3qEAAOSw0JVbm1FQ:rk:1:pf:0

I removed the passenger pegs, needed a bracket to hold the brake fluid reservoir - also cleaned up the pegs

Havent done the brakes yet - going to replace the lines etc with steel braid.

Also want to do a sprocket / chain swap for acceleration

I used a quadlock phone mount for a little bit - but took it off because I was playing with my phone too much.

I'd like to contribute my experience with adding engine mods to the WRR. It was very much NOT worth it for me. First it made the bike run like shit. It was always cranky to start compared to stock. It would stall way more on technical rock sections, and it would bog hard on whoops. Also it had worse bottom end torque, you can graph it up all day, but if you try to hold a hill in a high gear on modded vs stock, it's much worse with out the EXUP. I spent months trying to troubleshoot the fueling to make it better, but nothing helped. I had the PCV, I have also ridden a friends modded WRR with the FMF controller and it also bogged bad and stalled. You can try to make the bog go away by gearing the bike super low, that helps, but it's a band-aid.

Yes it was a faster WRR on the street, about as fast as a stock DRZ400. But if you spent the same money on mods on a DRZ you would be making nearly 50 HP easy. So IMO if you want power, get a DRZ.

I road my fully modded WRR back to back with a stock one off road, with the same gearing and tires, and it was not any faster. The only difference I noticed was that the power came sooner on the turn of the throttle. This got me thinking, so I put a quick turn throttle on my stock WRR and it was a huge improvement. I would strongly advise anyone looking to get more power from their WRR to try the R6 throttle tube mod first.

The throttle tube part #: 2C0-26240-00-00 is from the 2006 - 2015 Yamaha R6

Here is an amazon link:
http://www.amazon.com/Yamaha-2C0262400000-Grip-Assembly/dp/B005C59NO2

BikeMaster Removable Heated Grip Covers AM112012 https://www.amazon.com/dp/B00NYC7BH6/ref=cm_sw_r_cp_api_i_5VkXDbBAXSTB6

They go over and lace up. I’ve seen a few different ones. You’ll also want an in-line fuse and a relay. Let me know if you need a diagram and I can draw one. These aren’t the best because of size and the switch they come with is not the sturdiest but they work really well. I am hoping another company picks up the design and releases something similar but better. In the meantime I am happy.

Currently in low 40s where I am and with waterproof Bilt gloves these are enough to keep me comfortable. With thinner gloves they are too hot, but you can just turn them off once in a while.

depends what you like really. there is a whole range of stuff out there from soft and gummy, to rock hard, to dual compound, extra thick/thin and everything in between.

shortening the throttle tube is totally fine, you have to trim the tube and the grip sometimes so they don't rub against the bar end (in your case bar end mirror) and make the throttle stick. really there is no one way to do it.

personally i prefer grips on the softer side, enough to dampen vibrations and be comfortable, but not so soft as to wear down super quickly. usually they are called something like "superbike grips", something like this. renthal is a great brand, they make a ton of different ones.

The 520 says its made for claw and the 530 for palm but I have a slight claw grip and I still liked the 530 better. If you do get it though, make sure to get something like this to put on the sides of the mouse: https://www.amazon.com/TALON-998R-Grips-Rubber-Black-7-Inch/dp/B01FLQO5IU/ref=sr_1_cc_1?s=aps&ie=UTF8&qid=1511975978&sr=1-1-catcorr&keywords=talon+grip

Those big webbing belts you can get with the handles on each side are a bit weird looking but probably great for kids like yours to hang onto comfortably without having his face smushed into your back.

​

Like this

I have these Bike Master ones, and love them:

https://www.amazon.com/Bikemaster-Heated-Grips-Switch-Am19012h/dp/B00NYBZ4CQ/ref=sr_1_2?s=automotive&ie=UTF8&qid=1524009529&sr=1-2&keywords=bikemaster+heated+grips

There's a cheaper model that just has a button to control them, the ones I've linked have a little illuminuated LCD display which not only shows the current setting (Off, 1 -> 5) but also the current voltage, which is great because you're always aware of whether your battery/alternator are up to snuff.

Highly recommend them!

2010 Phantom here. I got pretty much everything on amazon, save for the seat and bags.

I just got done installing a Memphis Shades Batwing with lower deflectors, and a Ultimate seat with backrest on mine a couple weeks ago. The 6" recurve/spoiler windshield I ordered for the batwing is a bit to short for me (I'm 5'8"), which causes wind buffeting around my helmet. I'm still debating on going for a 9" spoiler or 11" standard. The seat, while being a bit more firm, is a lot more supportive than the stock one. I haven't had the chance to test out the backrest yet, but it seems like it will make longer trips much more comfortable/tolerable.

The Viking Bags I got for it should have been a bolt on affair, but they conflicted with the shock and seat so the bike is actually at a local shop right now getting them installed and the turn signals relocated. I should have ordered the shock cutout versions, but didn't check until after the return date, oh well, live and learn.

I'll take a photo and post it here when I get the bike back. If all goes well it should be tomorrow or wed.

Some other universal things I installed myself were Grip Puppy comfort grips, motorcycle bar phone mount, bluetooth remote control with bar mount.

For 77 dollars? Heck no. You could build yourself something more versatile for less. On amazon there is this set of resistance bands for 29 dollars that includes 4 other resistance bands plus additional accessories including an ankle cuff that you can use for the elbow cuff. You can buy a piece of PVC pipe cut it to about the size of your 6 iron put two of these grips, which cost $7, on the pvc using an adhesive. Find something similar and smaller than this and screw it into the pvc and you’ve just created exactly what they’re trying to sell you. All told you’ll probably spend about 40 bucks and you’ll get the added benefit of regular length resistance bands

I hope this helps you, I’m not knocking the product it’s just absurdly expensive for what you’re getting. There are many exercises you can do with the extra resistance bands with hands. Rotational exercises using the band can increase your core strength and hip strength.

These are what I have for 7/8ths:

https://www.amazon.com/PROGRIP-714BK-Black-125mm-Sport/dp/B000WO8MKY/ref=sr_1_1?keywords=PROGRIP+714BK+Black+125mm+Dual+Sport+Gel+Grip&qid=1570152055&s=automotive&sr=1-1

They're thicker than regular grips which for some reason helps out a lot with hand fatigue. Plus they're just really comfortable. I bought them November of last year and they're still like brand new

Also I've heard about those coils you put underneath your grips before, I'll look up some youtube reviews and see what kind of experience people have with those

Gun Grip works great and is pretty cheap. https://www.amazon.com/dp/B01FLQO5IU/ref=cm_sw_r_cp_api_WhnVBbBFE90CY

If you don’t mind a rougher texture fingerboard / skateboard grip tape is awesome but can tear your hands up over time if you move your hand position a lot.

There is also a foam version for fingerboards “Tech Decks” that Ive been meaning to try. https://www.amazon.com/dp/B00AW3ZRF8/ref=cm_sw_r_cp_api_RknVBbC6P81AG

https://www.amazon.com/gp/product/B01FLQO5DU/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

​

This is what i used for my GPW and it worked amazing and has held up perfectly. Been about a month already

Getting something like this: https://www.amazon.com/TALON-Grips-Material-Sheet-7-Inch/dp/B071LJXKMP

and trimming it to fit your mouse might be the best bet.

Nice bike, much fun shall be had! One cheap recommendation would be a set of new renthal grips, couldn't find a uk example but I got mine from a local bike shop for about a tenner. So much better than standard grips.

If that's all you want, you could get some rubber grip tape off Amazon. I use it for my pistol, but in theory it would keep it from marking your floor.

TALON Grips Rubber Material Sheet, 5" x 7", Black https://www.amazon.com/dp/B01FLQO5IU/ref=cm_sw_r_cp_api_i.76yb451QCS8

I don't know if that's what you're looking for, but it would probably get the job done. I love that stuff.

Hi, at no point does that say the pillion must touch the pegs

> pillion passengers must be capable of sitting astride a proper seat securely fixed to the motorcycle and be able to hold on effectively;

is the only must, there are ways of securely attaching children without making them touch the pegs, e.g. these and also these

throttle assist thingy:

https://www.amazon.com/Nuoxinus-Throttle-Motorcycle-Handlebar-Universal/dp/B016Q843CA/ref=sr_1_9?keywords=throttle+assist&qid=1557490632&s=gateway&sr=8-9


im a programer and over time i have spurts of carpal tunnel, so on long and short rides, it helps ease some pressure off my wrist using one of these things. you just rest the palm of your hand on it, adjust as needed.

your wrist isnt supposed to be bent 40-90 degrees straight up,

• Two RAM Balls mounted to the upper triple tree clamps
  
• Two RAM Arms (5") pointing out left & right
  
• iPhone XS Affixed to a MotoPowerPuck (wireless Qi Charger) held by aHondo Garage Perfect Squeeze mount
  
• InReach SE mounted toGarmin's USB Charger
  
• Sargent Seat Heated controller
  
• GoPro Remote mount(behind iPhone)
  
• Sena Remote control (far left affixed with rubber grippy material to the spacer left of grips)
  
• BurnsMoto Dual USB Hella DIN Port
  
• Grip Puppies
  
• Machineart Moto ADVance Handguards
  
• SW-Motech Mirror Extenders(I have wide shoulders)
  
• Touratech Collapsible Adventure Mirrors

https://smile.amazon.com/gp/product/B01FLQO5IU/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

Here's the one I use, it comes in a pretty big sheet and is easy to apply.

Talon Grip Sheets!! Cheaper than d-brand just not cut to shape.

I got some to make tiny strips to put on the sides of cases that need more grip

Edit: Downvoted?? They work wonderful! /u/tlaatonmai here's the link https://smile.amazon.com/TALON-998R-Grips-Rubber-Black-7-Inch/dp/B01FLQO5IU/ref=sr_1_2?ie=UTF8&qid=1505652150&sr=8-2&keywords=talon+grips


Here's some pictures: https://i.imgur.com/vqhBo80.jpg
https://i.imgur.com/bb1CT2c.jpg

I'm a warm water cephalopod swimming in cold waters, so I went for heated grips and am a very happy squid.

Did you know Amazon will donate a portion of every purchase if you shop by going to smile.amazon.com instead? Over $50,000,000 has been raised for charity - all you need to do is change the URL!

Here are your smile-ified links:

https://smile.amazon.com/TALON-998R-Grips-Rubber-Black-7-Inch/dp/B01FLQO5IU/

---

Never forget to smile again | ^^i'm ^^a ^^friendly bot

> I just wish there was some sort of texturing

How about something like this? It's what I was planning to use on mine.

EDIT: Searching a bit more revealed this!

I use these:

http://www.amazon.com/Oxford-OF693Z-Heaterz-Original-Handlebar/dp/B0045NK2K6

Fairly inexpensive and easy to install. I've never been in temps cold enough to need the highest setting. If I try to use it, my hands feel like they're burning.

It is an '82 XS400 special. It ran from 77 to 82. I have drag bars, but left all the cables the original length. The horn bracket got flipped upside down so I could access it/install a new one. I made a bracket that attaches to the bar running down in front of the engine to hold to LED fog lights, run by an auxiliary switch. Painted and wrapped the headers and have emgo shorty mufflers. Emgo pod filters, and a puck-style filter for the breather tube nipple. Led tails, led indicator lights, Upgraded headlight. Point of note on the headlight, mine was a sealed beam halogen. So to add a new bulb you have to buy an aftermarket reflector housing from candlepower.

EDIT: Also forgot Oury grips, cafe mirrors, new fuel lines, fuel filter and vacuum tube.

http://www.amazon.com/gp/product/B007CA6E56/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B002GTKAHQ/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B003T0ITF6/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B00HAQGO20/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B00230QCIY/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B006VFL0SO/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B00HDYB3P2/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B000N5UVME/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B0022ZUJGG/ref=oh_aui_detailpage_o09_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B000UKKSTI/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B00HJEGQQ2/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B007ZGKKMA/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B009SK7N8K/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

http://www.amazon.com/gp/product/B005ETCIO8/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

Looks like some sort of heated hand grips. Here is a Amazon link I found.

https://www.amazon.com/Western-Power-Sports-Heated-Grip/dp/B001A6CUB0/ref=sr_1_9?ie=UTF8&qid=1543204851&sr=8-9&keywords=heated+atv+hand+grips

Adding Grip Puppies to heated grips will extend the life of the grips indefinitely. And it makes them much more comfortable.

That's a real weird decision for a phone in their "Active" line.

Go add some strips of TALON Grip to the sides. It's normally used for firearms to add additional traction for better purchase.

I actually use a strip of it on the side of my MNML case so that my fingers can get a good grip on the phone (I'm left handed, in case you're wondering why it's on that side).

https://www.amazon.com/TALON-998R-Grips-Rubber-Black-7-Inch/dp/B01FLQO5IU/

http://imgur.com/46WryiN

Buy this: https://www.amazon.com/dp/B01FLQO5IU/ref=cm_sw_r_cp_api_RQi.xb8EANA48

Cheap and awesome material.

Example: https://imgur.com/r/MouseReview/8khlVXk

Nice ride, son! Now, hop on over to Amazon and buy some metric heated grips! =D

£36.49,suitable for 50cc upwards, get very warm fairly quickly https://www.amazon.co.uk/Oxford-Products-OF772-Heated-Grips/dp/B00GOVEUAU/ref=mp_s_a_1_6?keywords=oxford+heated+motorcycle+grips&qid=1575116272&sprefix=oxford+heated+&sr=8-6

£39.25, not used them so dont know what they're like https://www.amazon.co.uk/Oxford-Products-Commuter-Motorcycle-Hotgrips/dp/B00APJJQHY/ref=mp_s_a_1_7?keywords=oxford+heated+motorcycle+grips&qid=1575116272&sprefix=oxford+heated+&sr=8-7

Heated grips doesn't have to be so expensive. I'll treat my CBR with these babies next year ;)

http://www.amazon.com/BikeMaster-Motorcycle-Heated-Grips-Controller/dp/B009Z1KQ2M/ref=sr_1_1?ie=UTF8&qid=1449600110&sr=8-1&keywords=heated+hand+grips+motorcycle

As with so many other things, I found these beauties on amazon!

Progrip 714, easily the best cheap upgrade you can get.

I've been running foot pegs similar to these for three years now.

I dislike the cheap LED lights for visibility. I mean....why bother having indicators at all if they're not visible? Each time I go looking for new indicators I'm like....meh the stock ones do their job just fine.

I actually have an Abyssus V2 that I took down to 68g by removing the 10g weight that is screwed on inside and replacing the rubber side grips (which weigh another 3-4g) with this material, which grips better and is far lighter.

Definitely worth doing.

I have been looking for the same thing. I have tried all of these cases and what I found is that TPU cases are not anti-slip. They are more slippery like you said. PU leather cases have some grip. I tried this one and found it fairly anti-slip. But I wasn't a fan of the way it looked.

As of right now, I'm going to get a simple TPU case and stick this on the back. It adds a ton of grip and adheres very good.

Progrip 714BK Black 125mm Dual Sport Gel Grip https://www.amazon.com/dp/B000WO8MKY/ref=cm_sw_r_cp_apa_ZvBwyb7DQBT7P

Amazing and low cost grips. I put them on all of my bikes. I have them on my DRZ!

Get some of this to use on it man. It would look much better than the wood grain

I've seen a lot of people use gun grip tape to pad up their mouse, something like that would probably help you out here.

TALON 998G Grips Sheet (Granulate-Black, 5 x 7-Inch) https://www.amazon.com/dp/B01FLQO5DU/ref=cm_sw_r_cp_apa_i_.CecBbXRV2BFJ

I just got these, I really like them Bikemaster Heated Grips for 7/8in handlebars - One Size https://www.amazon.com/dp/B009Z1KQ2M/ref=cm_sw_r_cp_apa_4UzcAbH5S59NA

I bought it off amazon. But you can get just the tube as well. Or the motion pro for a slightly less aggressive effect. https://www.amazon.com/YAMAHA-2C0262400000-Yamaha-Grip-Assembly/dp/B005C59NO2/ref=mp_s_a_1_3?keywords=Yamaha+2C0262400000+Grip+Assembly&qid=1565977871&s=gateway&sr=8-3

I've been using these for 2 years. Helps with throttle control too.

https://www.amazon.com/Grip-Puppy-Comfort-Grips-Original/dp/B00CP9ADD8/

Thanks, I was unaware as I have just recently seen those. This is what I usually use, https://www.amazon.com/TALON-998R-Grips-Rubber-Black-7-Inch/dp/B01FLQO5IU/ref=sr_1_3?keywords=talon+grips&qid=1565646549&s=gateway&sr=8-3

One thing that isn't explicitly mentioned here is the difference between reflected and projected headlights. Halogen lights are reflected and LED's are projected. I'll let you do your own research on this matter because there are a bunch of articles that will communicate the difference between them better than I can. While you can put a LED H4 bulb in a relective housing, you definitely should NOT do this. The beam pattern will be all wrong and blind everyone. This is not ok. You should only use a projected bulb with a projection housing, so if you want to go LED you should pony up for a full on kit. This is all under the assumption that your bike now has a reflective housing.

Also, your stator might be able to keep up with the power output with the heated grips attached. I recently purchased the bikemaster heated grips and threw them on my bench power supply. At full output they only used 30W of power and these bad larrys put out plenty of heat. I've only ever needed them at half power riding in ~40F temps. Good luck.

https://www.amazon.com/TALON-998R-Grips-Rubber-Black-7-Inch/dp/B01FLQO5IU/ref=sr_1_1?ie=UTF8&qid=1510877714&sr=8-1&keywords=rubber+talon+grip

get rubber for a softer feel or granulate for something a little more rough (you can sand it out with 120g sandpaper if it's too rough, just make sure you do this before you put it on).

It's talon grip tape from
Amazon link : https://www.amazon.com/TALON-Grips-Material-Sheet-7-Inch/dp/B071LJXKMP?th=1&psc=1
And it's the one I bought from aliexpress which is cheaper than the talon grip but similar to it.
Link : https://m.aliexpress.com/item/32933326999.html?pid=808_0000_0101&spm=a2g0n.search-amp.list.32933326999&aff_trace_key=804d056dcb044953931fc19c8601cf02-1555125843610-05253-UneMJZVf&aff_platform=msite&m_page_id=PAGE_VIEW_IDCLIENT_ID(aefeMsite)NAV_TIMING(navigationStart)

http://forum.bodybuilding.com/showthread.php?t=146482473

I got these but have yet to put them on http://www.amazon.com/Sunlite-Road-Foam-Grip-piece/dp/B000AO5K42/

Get some grip puppies

https://www.amazon.com/Sportouring-Handlebar-Grip-Puppies-Grips/dp/B00CP9ADD8/ref=sr_1_1?ie=UTF8&qid=1501605757&sr=8-1&keywords=grip+puppy

Maybe look into heaver bar end weights too.

I usually take painkillers before, durying and after long rides.

TALON Grips Material Sheet, 5 x 7-Inch -- Rubber Black

https://www.amazon.com/gp/product/B01FLQO5IU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Try this: https://www.amazon.com/gp/product/B01FLQO5IU/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

​

Pistol grip material

https://www.amazon.com/TALON-998R-Grips-Rubber-Black-7-Inch/dp/B01FLQO5IU/ref=sr_1_4?ie=UTF8&qid=1551087471&sr=8-4&keywords=pistol+grip+tape

I just used grip puppies. If you don't mind not using leather.

https://www.amazon.com/dp/B00CP9ADD8/ref=cm_sw_r_other_apa_-eSUAbBDKBD5H

TALON 998R Grips Sheet (Rubber-Black, 5 x 7-Inch) https://www.amazon.com/dp/B01FLQO5IU/ref=cm_sw_r_cp_apa_j218Bb89PSZHC

https://www.amazon.com/TALON-Grips-Material-Sheet-7-Inch/dp/B071LJXKMP

Progrips I think...

TALON 998R Grips Sheet (Rubber-Black, 5 x 7-Inch)

https://www.amazon.com/dp/B01FLQO5IU/ref=cm_sw_r_cp_apip_DhKSeXWYHgHXk

I bought these for the tape https://www.amazon.com/TALON-Grips-Material-Sheet-7-Inch/dp/B01FLQO5IU?keywords=mouse+grip+tape&qid=1540671229&sr=8-8&ref=sr_1_8
Talon grips, material is very rubbery and doesnt peel away easily when heated with a blow dryer.

Talon gun tape. Amazon link here:https://www.amazon.com/TALON-Grips-Material-Sheet-7-Inch/dp/B071LJXKMP