Reddit mentions: The best shelf brackets
We found 148 Reddit comments discussing the best shelf brackets. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 111 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. MHMYDZ 4 Pcs Black Steel Heavy Duty"L" Corner Brace Joint Angle Bracket Shelf Bracket Wall Hanging with Screws 125mmX75mm/5 InchX3 Inch Decorative Corner Brackets Joint Angle Bracket
- Size:125 x 75 mm/5" x 3" (L*W*T) Mount Hole Dia.: 5mm/ 0.2" Thickness: 3mm/0.12”.
- maxium support weight of 35lb for a pair of this L bracket. Package included: 4 x Brackets , 8 x long Screws, 16 x short Screws, 8 x expansion pipe(Wood plank is Not included)
- The small solid and strong corner braces could be used for any shelf install, such as bookshelf, garden shelf, table and chair corner. It can play a good role regardless its small size, and make your home or garden more beautiful.
- 1,Use a drill to dig a hole on the wall or board and then install the screwholders. 2. use a screwdriver to tighten the screw on the brackets.
- Easy To Install Design Using Basic DIY Tools. Easily mount your favorite shelves in your home office, bathroom, kitchen, living room, dining room, bedroom, garage
Features:
Specs:
Color | Black |
Size | 5x3 Inch(4PCS Black) |
2. Ultra Hardware 96121 Shelf Brackets Grey, Pack Of 20
- ESSENTIAL ORGANIZATION: Make the most of any space with decorative organization. Shelving is essential for your books, potted plants, and all kinds of home items. Create a balanced and beautiful environment in your home by installing simple shelves
- EASY INSTALLATION: Each bracket comes with pre-drilled installation holes to guide you through the process. Just pick your shelf size and position, level it out, and screw into the desired place. They can be installed in almost any place on any level for a range of options
- TONS OF VARIETY: Ultra Hardware’s product lines offer a full rand of colors and sizes to accommodate every project and part of your home. Ultra Hardware gives every homeowner an option for that all-important finishing touch to complete a room makeover or renovation
- TRUSTED BRAND: Ultra Hardware offers quality products for builder’s hardware and cabinet hardware. Ultra Hardware products span 14 categories including Storm & Screen Door Hardware, Door Security, Builder’s Hardware, Gate & Garage Hardware, Home Hardware, Wire Goods and more
- PRODUCT SPECIFICATIONS: Package contains (1) Ultra Hardware Enamel Steel Shelving Bracket - Pack of 20 (Grey, 10" x 12"). Limited warranty – 25 years. Steel construction with durable enamel finish. Heavy gauge 0.0354. Each bracket has pre-drilled installation holes
Features:
Specs:
Color | Gray |
Height | 2 Inches |
Length | 11.75 Inches |
Size | 10"x12" |
Width | 9.75 Inches |
3. Amarine Made Pair Stainless Steel Solid Shelf Brackets,8",10",12", Shelf Support Corner Brace Joint Right Angle Bracket (12"X6-1/2")
Product Name : Angle Bracket;Material : Stainless SteelColor : Silver Tone; Hole Quantity : 4 HolesBracket Size :12"X6-1/2X1/8"Hole Dia. : 6mm / 0.24"Package Content : 2 x Angle Brackets
Specs:
Color | Silver |
Size | 12"X6-1/2" |
Weight | 1.75 Pounds |
4. Leviton 47612-UBK Universal Shelf Bracket used with Structured Media Center, White
Allows security batteries and other products to be mounted inside any Leviton Structured Media CenterVertical and horizontal slots on bracket to accommodate Velcro strips, ensuring vertical and horizontal stabilityComes with four 8 Inch long Velcro stripsMade of white powder-coated 18 gauge sheet me...
Specs:
Color | White |
Height | 0 Inches |
Length | 0 Inches |
Number of items | 1 |
Size | One Size |
Weight | 0.9 Pounds |
Width | 0 Inches |
5. Leviton 47612-DBK Data Plastic Bracket, White
The Data Bracket is for mounting switches, routers and modems within a Leviton Structured Media CenterAll plastic brackets, made of sturdy white ABS plasticCome with push-lock pinsUniversal screw holes accept a variety of screw configurationsIncludes slots for easy fastening of routers, switches, et...
Specs:
Color | Image |
Height | 0 Inches |
Length | 0 Inches |
Number of items | 1 |
Weight | 0.18 Pounds |
Width | 0 Inches |
6. Decko Products 49143-10 Heavy-Duty Shelf Bracket, 10.5-Inch X 7.5-Inch, White, 10-Pack
- Use on 12" dimensional lumber, actual shelf width approximately 11-1/4"
- Bracket measures 10.5-Inch by 7.5-Inch size
- Made from high quality steel, 3 predrilled 1/4" holes on both sides for fasteners not included
- Use in home, shop, garage, or business, great for shelving systems
- With Decko shelf brackets the possibility are endless
Features:
Specs:
Color | White |
Height | 7.5 Inches |
Length | 10.5 Inches |
Number of items | 10 |
Size | 10.5-Inch X 7.5-Inch |
Weight | 1.05 Pounds |
Width | 1.18 Inches |
7. Simpson WBSK Workbench & Shelving Hardware Kit
- Instruction sheet that includes lumber cut list
- DIY Done Right booklet that offers inspiration and instruction to build other home projects with Simpson Strong-Tie products
- 8 Rigid Tie RTC2Z connectors
- 4 #6 x 2 1/2" flat-head screws
- 1 Box of Simpson Strong-Tie SD #8 x 1 1/4" screws and 20 #6 1-1/4-inch flat head screws, Made in USA
Features:
Specs:
Height | 0.51 Inches |
Length | 6.25 Inches |
Number of items | 1 |
Size | Pack of 1 |
Weight | 0.15 Pounds |
Width | 0.82 Inches |
8. Rubbermaid 1877642 Decorative Shelf Bracket, 6 by 8-Inch, Arch, Grey
- Decorative brackets add stylish flair to your display shelving; Perfect for displaying photos or collectibles
- Asymmetrical design works with 2 different shelf depths; 6-inch side with 8-inch shelves, 8-inch side with 10-inch shelves
- Includes 1 shelf bracket and installation hardware
- Durable metal construction will provide dependable, stable support
- Shelf is not included Requires a drill, drill bits and screwdriver (not included)
Features:
Specs:
Color | Gray |
Height | 6 Inches |
Length | 8 Inches |
Size | Arch |
Weight | 0.5 Pounds |
Width | 0.75 Inches |
9. Antrader Corner Protector 24pcs Metal Box Edge Safety Guard Bronze Tone 1" x 1" x 0.35"
Package Content: 24pcs x Box Corner Protector, Some ScrewsColor: Bronze Tone; Material: MetalDimension: 25 x 25 x 9mm/1" x 1" x 0.35"(L*W*H)Mount Hole Diameter: 2.5mm/0.1"Net Weight : 94g
Specs:
Color | Bronze Tone |
Size | 25 x 25 x 9mm/1" x 1" x 0.35"(L*W*H) |
10. Alise 1-Inch Dia Shower Curtain Closet Rod Holder Pipe Flange Socket Ceiling Mount Bracket Pipe Fitting Parts Supports Can Adjust Fixed,FL5005-2P 2 Pcs Stainless Steel Chrome Finish
Constructed of stainless steel ensuring durability and dependabilityStainless Steel Chrome Finish,to protect against corrosion & rust.Fits 25mm/1inch dia. rod,Can Adjust FixedMount Hole Diameter: 8x10mm/ 0.32x0.4"; Fit Pipe Max. Diameter: 25mm/ 1";Height:150mm/6"Package Including 2 x Support Bracket...
Specs:
Color | Brushed Nickel |
Height | 3.2 Inches |
Is adult product | 1 |
Length | 6 Inches |
Size | FL5005-2P |
Width | 1 Inches |
11. Decko Products 49144-10 Heavy-Duty Shelf Bracket, 10.5-Inch X 7.5-Inch, Black, 10-Pack
- Use on 12" dimensional lumber, actual shelf width approximately 11-1/4"
- Bracket measures 10.5-Inch by 7.5-Inch size
- Made from high quality steel, 3 predrilled 1/4" holes on both sides for fasteners not included
- Use in home, shop, garage, or business, great for shelving systems
- With Decko shelf brackets the possibility are endless
Features:
Specs:
Color | Black |
Height | 7.5 Inches |
Length | 10.5 Inches |
Number of items | 10 |
Size | 10.5-Inch X 7.5-Inch |
Weight | 1.05 Pounds |
Width | 1.18 Inches |
12. 24" Solid Steel Heavy Duty Floating Shelf Bracket Made in The USA
- Heavy Duty Floating Shelf Bracket. Solid Steel Hidden Bracket
Features:
Specs:
Color | Steel |
Height | 1.5 Inches |
Length | 24 Inches |
Size | 7 x 1.5 x 24 |
Width | 7 Inches |
13. Alise J5207-4P Stainless Steel Shelf Brackets 5x3 Inch,4Pcs Brushed Nickel
Constructed from high quality Stainless Steel,ensuring quality and longevityHand brushed finish stainless steel shelf brackets,will not rust,sturdy and durableSize: 125 x 75 x 2.8mm/5" x 3" x 0.11" (L*W*T); Mount Hole Dia.: 5mm/ 0.2"Package Include : 4 x Brackets and 24x Screws.3MM solid thickening ...
Specs:
Color | Brushed Nickel |
Height | 0.12 Inches |
Length | 5 Inches |
Size | 5x3 Inch |
Weight | 0.78125 Pounds |
Width | 3 Inches |
14. Black HD Steel Shelf Bracket, 19-1/2" Deep x 13" High
Size : 20 inchFinish : BlackMaterial : Cold Rolled SteelHeavy duty bracketA corrosion-resistant black epoxy coat finish
Specs:
Color | Black |
Height | 1.1 Inches |
Length | 19.6 Inches |
Number of items | 1 |
Weight | 2 Pounds |
Width | 14.4 Inches |
15. L Brackets WEBI Shelf Brackets for Shelves:8'' L,4 mm Thick,90 Degree Stainless Steel Corner Brace,Right Angle Bracket for Wood,Furniture,Brush Nickel,2 Packs
★【BRACKET SIZE】: 200*160*30/8"*6.30"*1.18"(L*L*W*T);Thickness:4mm.★【STYLISH LOOK】:Brushed nickel shelf brackets,Color:silver★【HEAVY DUTY】: Made of premium stainless steel to ensure sturdiness & durability, Heavy duty corner bracket for long daily use.★【PACKAGE CONTENT】 : 2x C...
Specs:
Color | Brushed Nickel |
Height | 6.3 Inches |
Length | 7.87 Inches |
Size | 8"*6.3"(2 Pcs) |
Weight | 1.81 Pounds |
Width | 1.18 Inches |
16. Kv Steel Shelf Standard 48" Brown
- 5/8" Wide X 3/16" Deep
- Nails not included, Search: KV Nails For Standards
- Other colors available, Search: KV Steel Shelf Standard or KV Aluminum Shelf Standard
- Support clips needed, Search: KV Shelf Support Clip
- Accessories Search: KV Steel Shelf Support For Shelf Standard or KV Rubber Cushion For Shelf
Features:
Specs:
Color | Brown |
17. YUMORE L Bracket, 5" x 3" Max Load: 35lb/15KG Heavy Duty Stainless Steel Solid Shelf Support Corner Brace Joint Right Angle Bracket, Pack of 4
- STURDY & DURABLE - Shelf Bracket and the fitting screws are made of solid stainless steel, brushed finish, is rustproof, anti-corrosion, more strong and durable, not easy to bend and deformation
- BRACKET SIZE - 35lb/15kg Bearing Capacity for a pair of bracket. 125 x 75 x 3mm/5" x 3" x 0.11" (L*W*T). The small solid and strong corner braces Enough to be used as any shelf install, such as bookshelf, garden shelf, table and chair corner. It can play a good role regardless its small size, and make your home or garden more beautiful
- QUALITY CONTROL - Because the bracket is small, it is need to be very accurate angle control in the production. Our brackets are all the 90 degrees, different from others bracket in the markets, the Angle of many brackets can only reach 87 degrees
- EASY INSTALLATION - Come with mounting accessories, premium stainless Steel screws and top quality anchors.Use in home, shop, or business, great for shelving systems. Be a handy man, enjoy happiness from DIY
- QUALITY ASSURANCE - Package includes: 4Pcs L Brackets(5x3"), 8Pcs Plastic expansion Anchor(M8), 8Pcs long Screw(M5x35), 16 Pcs short Screw(M5x16). If any issue with your YUMORE products, please be free to contact us. Backed by YUMORE's Limited Lifetime
Features:
Specs:
Color | Brushed Nickel |
Height | 3 Inches |
Length | 5 Inches |
Size | 5"x3" |
Weight | 0.74 Pounds |
Width | 0.7 Inches |
18. Folding Shelf Bracket (16")(Sold Each)
Knape & Vogt206 ZC 16Shelf SupportsZincSold per each
Specs:
Color | Zinc/Anochrome |
Height | 1.3 Inches |
Length | 15.39 Inches |
Weight | 5.25 Pounds |
Width | 1.42 Inches |
19. NACH js-90-423S Borris Cast Iron Industrial Shelf Mount Bracket, Small 3.54 x 2.75 x 1.77 Inches, Black, 4 Pack
Specs:
Color | Black |
Height | 2.8 Inches |
Length | 3.5 Inches |
Number of items | 4 |
Size | Small |
Weight | 0.15 Pounds |
Width | 1.8 Inches |
20. king do way Industrial Black Iron Pipe Bracket Wall Mounted Floating Shelf Hanging Wall Hardware Decor for Farmhouse Shelving Hardware Heavy Duty (2pcs)
SHELF BRACKET STANDARD: PIPE Flange Diameter- 80mm/3.1"; Short arm: 65mm/2.5"; Long arm: 150mm/5.9"(Including flange and elbow).PACKAGE INCLUDED-2x Pipe Shelf Bracket(Wood plank is Not included)Great Decoration: Believe it or not, pipe shelves can actually look chic in the bedroom. It looks cool and...
🎓 Reddit experts on shelf brackets
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where shelf brackets are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
Are you in the US? For some reason, I cant find that coutertop on the Ikea US site but it is on the GB site.
If you can buy another piece of it, and it's finished on the bottom too, and have access to (or a friend with) a table saw, then I like /u/MrSnowden's plan. Some shelf brackets like this would match the existing style pretty well.
I think on the wall the whole width of the desk would look good, as long as the pieces are like <12" deep. 8" might be perfect; do you need to store/display anything in particular on the shelves?
So what I've done for my 121x80cm (3000pc) puzzle is the following (much like u/Excipa):
You need a curtain rod with long stanchions
See my little doodle for reference
Essentially, you find the longest curtain rod stanchion you can find and mount them directly over the window sills, instead of on either side like you would normally
Amazon Link to example of 6" stanchion
This gets the curtain in front of the pipe, but not covering the pipe or near it to cause a heat issue.
You could also drop the curtain down from the ceiling in the same manner...but finding a curtain stanchion sized perfectly for your needs might be difficult. In that instance, you might be best served getting galvanized pipe and fittings and attaching it through the ceiling drywall using toggle bolts. Something like this
Then just get a nice glossy spray paint and paint the pipe whatever color you want
But regardless, the curtain will either have to be inside the sill like a shower curtain (I'd go with 2" window blinds instead cus it will look better than an interior curtain) or...you bring the curtain out in front of the pipe. The downside to that being you will have light spill on the ends. But if you are just doing sheer curtains or semi sheer, it will still have the same effect
12' of 1x12 pine is around $20. You'll probably want brackets every 16-32" so for 12' of shelving you'll need 5-9 brackets.
Brackets prices all over, but plain ones are super cheap.
My current bed was chopped from a bunk bed and can fit fullsized totes underneath it, it's great.
Bonus is that you can paint the shelves to be whatever color to match walls/color scheme or just leave them.
Floating shelves would be a challenge for records. They cannot support a lot of weight due to their design. So in order to get a full shelf (say 4 ft long), you'd need some sturdy floating shelf support AND make sure to have them attached to the studs.
If you look at those (https://www.amazon.com/Solid-Steel-Heavy-Floating-Bracket/dp/B01FL4551S), the rating is 150 lbs, but that's for 6" shelves. With records that are 12", I'd say that the rating is divided by 2. Assuming that a record is 0.5 lbs, that means that a shelf like that can only support about 120 records. But at 24" long, you can't really put more than 100 records anyway.
Adding the cost of the shelf (assuming $10). It would cost $50 per 100 records.
Unless you are ready to spend a fair amount of money, Kallax are still the best choice around.
&#x200B;
[Logitech G920] (https://www.amazon.com/Logitech-Dual-Motor-Feedback-Driving-Responsive/dp/B016LI8SCG?th=1) - Best setup I could find for under $500+. I really like it. Solid quality, holds up to (ab)use well.
Rubber Pads - I put these on the wheel and shifter to help hold it to the desk better. I was dealing with sliding without them. I use the flat ones on the underside of the mounts, which press against the top of my desk.
[Half Keyboard] (https://www.amazon.com/gp/product/B07D6NTPWH/ref=oh_aui_detailpage_o01_s00?ie=UTF8&amp;psc=1) - Gives some extra buttons close to your wheel since you'll lose out on some hotkeys.
[Desk Brackets] (https://www.amazon.com/gp/product/B01LYL14WV/ref=oh_aui_detailpage_o00_s00?ie=UTF8&amp;psc=1) - I mounted these to studs in my wall, and on the underside of my desk. I keep my screens wall mounted, and my PC on a platform under my desk. These keep the desk super stable.
edit: Added a piece of equipment.
You're right that having the 2x4s rest on the floor will help with the weight, but the remaining weight will still want to pull away from the wall. Regardless, I think that 3 appropriately sized anchors per stud into the wall will be enough. You won't need an anchor at all near the bottom, so I'd keep them nearer the top, maybe one above each shelf or two.
The bigger problem you'll have with that design, I think, is properly supporting the shelves with wooden shelf supports. This is especially true if you're fastening the 2x4s flat against the wall, since you'll now be fastening the shelf supports to the 1.5" side. Instead of making wooden shelf supports, I'd strongly suggest just using some sort of metal 90-degree shelf bracket.
I was going to suggest a triangular bracket too, but your idea to use a half-junction to make it removable is extra clever. You could actually do it again: split the lower section since you're already planning on bolting it in place. That would mean that removal doesn't require sliding it off the bottom, just removing bolts.
I think a triangular bracket like this is the best you can do without adding extra supports^() or stronger materials. It'll reduce the stress on the top horizontal pipe as much as moving the posts inwards by that much. It'll also remove some stress from the top corner connector.
You could also accomplish the same thing with an angle bracket, like used for shelving (example). Being metal doesn't really help any but it'd be hard to find one that reaches as far as you could get with PVC.
---
^() I assume an extra strut in the middle would be super awkward. You could also tie it to the ceiling with string. That's very simple but whoever owns the ceiling might not appreciate it.
You wont be able to buy them as completed shelves. The adjustable shelf supports are a two part system. The part you have which is similar to this and then there are clips that look like this this which fit into the small gaps in the vertical strips that you have. That two part system is the support system for the shelf that you make yourself typically out of plywood to fit the span between the clips. There are things that can be done to make the plywood look better but that's the gist of it.
I'm sure the next question is will the clips that I linked fit in your existing tracks. Unfortunately I can't comment on how interchangable those are. You could look on the manufacturers site to see if they post any dimensions that you could compare yours to. Otherwise on Amazon you could post a question to see if someone will measure one of theirs. The last time I asked for a really specific dimension on there for some cables I got a lot of half assed answers for different dimensions that I didn't ask for. You might have better luck.
I've seen a few of these built, so I wanted to give them a try. Flew some sorties tonight and pretty happy with them so far. Really nice to have something which can be removed easily when I'm done.
3" Drill Press Vice
Steel brackets
Extreme Velcro
I found this extreme velcro on a whim and it's awesome. It adheres to anything and locks your stick/throttle down tight, yet can still be removed when you are done. I used it to attach my IR clip to the headphones, and it's great there also.
Boards are simply a cheap bamboo cutting board I got at Walmart and sawed in two. Add the bolts and screws and I'd say this whole thing was less than $50.
Maybe be aware the brackets are on the small side, so if you want something that will hang lower, you'll want to look at something different.
Edit: just wanted to say....you'll need to wipe down the vices when you get them. They are covered with a light oil to prevent rusting I'd guess. Take a rag and give them quick wipe all over (the jaws too, they will leave a mark on your desk!)
Thanks so much.
I grabbed these heavy duty brackets. They have a release lever, but that might be necessary for this size/weight.
Sounds like I'll have to be very precise or they will not fold correctly, and also be wary of mounting the surface flush with the wall. I'm also researching as much as possible about shear weight and pull weight for screws and studs... I wish I knew what kind of wood my studs were and what thickness my drywall is.
It sounds like 2.5" size 8 screws put perfectly straight into the wall. I'm reevaluating the table surface though. If it's hanging from the mount vertically part of the time, I don't want the screws in the surface to slowly tear through the wood...
I wouldn’t risk this. It doesn’t seem terrible at first but if you imagine the liquid weight and the height above that few mm overhang it would be an easy tip-over if it got banged the wrong way. It might be best to make a small platform that covers the whole bottom, plus a cm or so, and put the tank on that. And then add a little support underneath with a few of those right angle shelf support things.
Kind of like this but smaller
I agree with the others. It's completely possible to not do it, but this is a long table top that needs support in the middle. Consider some standard shelf wall mount brackets to support the middle of the table if that's any better for you. Even with something like this screwed to the wall and to the desk, I wouldn't stand on it.
i’ll be honest with you, i don’t even have a bookshelf so i can’t answer that question with 100% confidence. i would assume just looking up shelf bracket, something like this would probably work
https://www.amazon.com/Leviton-47615-NYL-Push-Lock-Structured-Centers/dp/B0018DOBG2/ref=pd_sim_60_2?_encoding=UTF8&amp;psc=1&amp;refRID=HAKJKZK4EC0XSH0KE18M
It uses those little black stand off things. You insert it into the hole and then push down on the top and it locks down. If you by Leviton switches/patch panels, they usually come included with it (look at the Leviton switch I linked above, it's attached to the four ends of the switch). And for mounting gear in it that's not made by Leviton, they have special brackets that just hold a device in place and mount using Velcro straps. But save money and just mount it yourself using double sided tape/velcro straps etc...
Here is their universal bracket to mount non-leviton hardware:
https://www.amazon.com/Leviton-47612-UBK-Universal-Bracket-Structured/dp/B0018DKWGA/ref=pd_sim_60_1?_encoding=UTF8&amp;psc=1&amp;refRID=YRPJ81ADVX50J2PK7EAD
Here's another:
https://www.amazon.com/Leviton-47612-DBK-Plastic-Bracket-White/dp/B0007SN5E8/ref=pd_sim_60_4?_encoding=UTF8&amp;psc=1&amp;refRID=66BAHF93TW6PX8GR97RV
I would have done something with a shelf brace and some command strips. If you placed 2-3 strips on the side on the wall and then you could use zip ties to strap it to the brace. Or just drill in there wall and patch it up, I've put tons of holes with out thinking in my apt knowing I can path them when I move.
Amarine-made Pair Stainless Steel Solid Shelf Brackets ,8" ,10" ,12" , Shelf Support Corner Brace Joint Right Angle Bracket (12"X6-1/2") https://www.amazon.com/dp/B017GS6GUQ/ref=cm_sw_r_cp_api_tMUExbE01DPNX
Command Large Picture-Hanging Strips, Black, 4-Strip https://www.amazon.com/dp/B00404YO1I/ref=cm_sw_r_cp_api_eOUExb9GBHEW5
Also to clean it up a bit:
Wiremold CMK50 Cord Mate II Kit https://www.amazon.com/dp/B0015EDVVU/ref=cm_sw_r_cp_api_CSUExbRZ17VST
As mentioned, Cofer and Randall Brothers will usually have higher grades in stock. You are going to be hard pressed to find untreated pine 4x4s. Cedar is pretty readily available though.
Although, unless you are trying to build some heirloom workbench to pass down to your kids, or need something to rebuild transmission on, I don't really see the point. Fancy dimensional pine isn't really the thing you want to spend time and money sourcing to build something you'll just hit with a hammer and drip paint on. It's got better engineering values and maybe no grade stampings, but you aren't making roof trusses or millwork here. If this is a basic basement homeowner workbench, just buy something like this Simpson kit and lumber from HD and you'll have a hard time breaking it.
https://www.amazon.com/Simpson-WBSK-Workbench-Shelving-Hardware/dp/B00K774V2Y
Buy some l brackets like these https://www.amazon.com/MHMYDZ-Bracket-125mmX75mm-Decorative-Brackets/dp/B0768SH78H/ref=mp_s_a_1_5?ie=UTF8&amp;qid=1540497208&amp;sr=8-5&amp;pi=AC_SX236_SY340_FMwebp_QL65&amp;keywords=l+brackets&amp;dpPl=1&amp;dpID=416s-7MkALL&amp;ref=plSrch and bend them into a V to fit your deck
I recently installed a shelf for my succulents and I would think it would work well for keyboards
I used these L brackets https://www.amazon.com/dp/B0768SH78H?ref=ppx_pop_mob_ap_share
and Lowe’s/Home Depot have shelves for like 7-15 bucks depending the size .
Black pipe, some elbows and mounting plates
Kind of like this from Amazon
If you mount the light under the shelf, will there be anything on top of the shelf? I ask because the light fixture will probably need room to vent any heat so you wouldn’t want it flush on the shelf if the top of the shelf it’s mounted to is covered up. Some options would be to put the plants on the top shelf, then use some shelf brackets with drywall anchors or screwed into studs. Then the light could be secured to the shelving brackets and be suspended above the shelving rack. Something like this (but you can find cheaper at Walmart or Home Depot) brackets
I would understand that price for full blown rack equipment
...but...
I just want something like https://www.amazon.com/Leviton-47612-DBK-Plastic-Bracket-White/dp/B0007SN5E8
The modem and router are held in by one of these:
Leviton 47612-UBK Universal Shelf
These have a standoff/negative space behind them so thats where all the power wires for everything are coiled up. Once you have one of these, you can get some 3/4"x1/16" aluminum bar from Lowes/HD and cut it to length and transfer the spacing for the pushpin holes to it from one of the Leviton shelfs. Drill those out and put some of these in there:
Leviton Push-Lock Pins
I painted mine with white appliance enamel. You can put those wherever you need them and use some velcro cable wraps around both sides of them to secure the devices to the enclosure.
It looks like Leviton actually makes a version of these now:
Leviton Universal Bracket
...but for $23/pr you can do better/stronger if you go the thin aluminum bar route and make about 6/8 of them for about $10, including the Leviton push lock pins.
Not OP: You'll need
https://www.amazon.com/KINGSO-Industrial-Floating-Hardware-Farmhouse/dp/B071X6KLK9
One shelf board, I'd recommend hardwood vs. MDF board as MDF board will blister when water sets on it.
Looks like one of these Leviton data brackets:
https://www.amazon.com/dp/B0007SN5E8/ref=cm_sw_r_cp_api_Dp9uzbMH02Y62
Not everything fits the hole pattern so I used this shelf for mine:
https://www.amazon.com/dp/B0018DKWGA/ref=cm_sw_r_cp_api_br9uzbN65X3N1
This set and about $75 worth of lumber from the Home Depot did it for me!
Simpson sells a "workbench kit", that contains 8 "rigid tie connectors" + screws + a little manual that describes how to build pretty much what that site has on it. You have to buy the wood separately. I priced the kit out on a few sites compared with buying the connectors individually and it worked out a bit cheaper in most cases.
This is the Simpson kit i used, i used two kits... one for the longer bench and another for the saw stand... http://www.amazon.ca/Simpson-WBSK-Workbench-Shelving-Hardware/dp/B00K774V2Y
I did not have studs by the window so i used anchors, which came with the metal pipes (https://www.amazon.com/dp/B071X6KLK9/ref=cm_sw_r_cp_api_i_zu1KDb13EZBSG).