Reddit mentions: The best scissor lift jacks
We found 43 Reddit comments discussing the best scissor lift jacks. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 20 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Extreme Max 5001.5044 1000 lbs. Motorcycle Scissors Jack - Wide
- Extends up to a 14" height
- Easily hand-operated using 7/8" socket or wrench (sold separately) - *Do not use an impact wrench or powered drill to operate the lift
- Durable rubber padding on platform
- Heavy-duty steel frame
- 1000 lb. weight capacity; will not lift trikes
Features:
Specs:
Color | Red |
Height | 0 Inches |
Length | 0 Inches |
Number of items | 1 |
Release date | December 2015 |
Size | Wide |
Width | 0 Inches |
2. BIG RED T10152 Torin Steel Scissor Lift Jack Car Kit, 1.5 Ton (3,000 lb) Capacity, Red
Collapsible, steel scissor lift jack has a compact design that can be used as a rugged replacement jack or as an extra utility jack that can be stored in the trunk of your carFeatures a lifting range of 4-1/8" to 15-1/8" with a 1.5 ton (3,000 lb) capacityEngineered using a drop forged alloyed steel ...
Specs:
Color | Red |
Height | 9.45 Inches |
Length | 26.38 Inches |
Number of items | 1 |
Release date | August 2017 |
Size | 1.5 Ton (3,000 lb) |
Weight | 7.7 Pounds |
Width | 19.09 Inches |
3. ZENY 1100 LB Motorcycle Center Scissor Lift Jack Hoist Stand Bikes ATVs Scooter Crank Stand
Solid steel construction in a red and black powder coated finishTwo (2) variable screw adaptersSimple crank operation12 cm removable crank handleFits Cruisers, Choppers, Can Am Spyder, Trikes, Sport Bikes
Specs:
Color | #01 |
Height | 13.19 Inches |
Length | 8.07 Inches |
Weight | 27.778245012 Pounds |
Width | 3.54 Inches |
4. liftmaster 1100 LB Wide Deck Motorcycle Center Scissor Lift Jack Hoist Stand Bikes ATVs
- Solid steel construction in a blue and black powder coated finish
- Simple crank operation
- Designed to fit most motorcycle models
- For use in the garage, shop, or at the track
- 9 Inch Wide Deck
Features:
Specs:
Color | Blue |
5. Camco RV Leveling Scissor Jack Socket Drill Adapter, Fits 3/8" and 1/2" Power Drills, Works with All 3/4" Hex Drive Jacks (57363)
Reduces time and effort to raise or lower Scissor jacksFits 3/8 inch or 1/2 inch power drillsWorks with all 3/4 inch hex drive jacks
Specs:
Color | Silver |
Height | 6 Inches |
Length | 1.3 Inches |
Number of items | 1 |
Release date | March 2016 |
Weight | 0.15 Pounds |
Width | 2.4 Inches |
6. Extreme Max 5001.5047 1100 lb. Motorcycle Scissors Jack, Narrow
- Lifts cruiser or touring motorcycles from 3-5/8" - 16-1/2"
- Designed for front or rear manual lifting using included handle
- Adjustable/removable dual frame adapters add 2" - 3-1/4" of lift
- Heavy-duty steel frame with welded base brackets for permanent mounting
- 1100 lb. weight capacity
Features:
Specs:
Color | Red |
Height | 0 Inches |
Length | 0 Inches |
Number of items | 1 |
Release date | December 2015 |
Size | Narrow |
Width | 0 Inches |
7. - Bend Pak Full-Rise Scissor Lift - 7000-Lb. Capacity, Model# SP-7X
- Exact fit precision machined drivers
- Wiha exclusive CRM-72 tool steel blades
- Hard chromed wear resistant finish
- Handles proportioned to blade size
- Free turning finger tip control cap
Features:
Specs:
Size | Large |
Weight | 2596 Pounds |
8. LEADBRAND Scissor Jack 1.5 Tons(3,307 lbs) Capacity Ratchet Handle Saving Strength Design
Net weight :2.86kg(6.3 lbs), Lift range from 4.09 inches to 15.15 inchesWith the scissor jack you can easily and quickly adjust the height of your vehicles. Thanks to the handy ratchet handle and the smooth-running spindle, changing tires is child's play from now on.The solid base plate also ensures...
Specs:
Color | Black |
Height | 4.09448 Inches |
Length | 16.1417 Inches |
Weight | 5.51155655 Pounds |
Width | 3.5433 Inches |
9. Black Bull EJ212 12 Volt Fully Automatic Electric Car Jack
Compact size stores in car for emergencies2,000 lb. capacity, 5 to 14 inch lifting heightPush button controller with 12 foot cord, plugs into car 12 volt dc power outletPackaged in plastic storage case for easy transport and storageLightweight design; case and jack weighs only 11 pounds
Specs:
Color | Regular |
Height | 9.25 Inches |
Length | 5 Inches |
Number of items | 1 |
Size | 2000 IL |
Weight | 5.02 Pounds |
Width | 17 Inches |
10. TONDA 2 Ton Portable Car Scissor Jack for Sedan and Coupe
2 Ton capacity; High lift; Heavy duty. The max lift height is 385mm, about 15.4 inches.Superior, high quality steel construction.Simple and lightweight packed to car.All welded steel frame construction with rust resistant finish for longer tool life.Ideal for coupe, sedan, farm, and shop use. Design...
Specs:
Color | Silver |
Size | 2T |
Weight | 7.68 Pounds |
11. Hi-Lift Jack TM-750 2"-3" Adjustable Tube Mount
- The Hi-Lift Jack Adjustable Tube Mount system is designed to allow secure mounting of Hi-Lift jacks to tube bumpers, bull bars, roll cages or roof racks. Manufactured from 6061-T6 structural aluminum with stainless steel hardware.
- Fits tubing 2 - 3 inches in diameter
- Manufactured from high quality structural aluminum
- Stainless steel hardware
- No drilling required
Features:
Specs:
Height | 0 Inches |
Length | 0 Inches |
Number of items | 1 |
Size | 2-3 Inches |
Width | 0 Inches |
12. Pit Posse PP2551S Motorcycle ATV Scissor Floor Jack Lift Table Stand with Caster Wheels 13 Inches Thru 36-Inch-High - Stable - Safe - Comfortable - 2 Years Warranty
✅ A PROFESSIONAL LIFT FOR YOUR HOME/GARAGE/SHOP- This hydraulic scissor lifter is designed to allow you to repair your motorcycle, ATV, and dirtbike smoothly. Perfectly centers your bike with both wheels in the air, and you can adjust the height anywhere between 13 inches thru 36 inch off the grou...
Specs:
Height | 15.2 Inches |
Length | 20 Inches |
Weight | 63.8 Pounds |
Width | 18.5 Inches |
13. 1500 Lb. Capacity ATV/Motorcycle Lift
4 built-in positioning hooks for use with tie-downsTwo-hand wheel brake prevents lift/jack movementReturn spring for automatic releaseExtra-long handle for easy liftingTwo 2-1/2" diameter swivel casters
Specs:
Weight | 98 Pounds |
14. Hi-Lift Jack TM-700 1"-2" Adjustable Tube Mount
The Hi-Lift Jack Adjustable Tube Mount system is designed to allow secure mounting of Hi-Lift jacks to tube bumpers, bull bars, roll cages or roof racks. Manufactured from 6061-T6 structural aluminum with stainless steel hardware.Fits tubing 1 - 2 inches in diameterManufactured from high quality str...
Specs:
Height | 2.1 Inches |
Length | 12.1 Inches |
Number of items | 1 |
Release date | January 2002 |
Size | 1-2 Inches |
Weight | 2 Pounds |
Width | 4.1 Inches |
15. Dragway Tools 1100 LB Wide Deck Motorcycle Center Scissor Lift Jack Hoist Stand Bikes ATVs
- For use in the garage, shop, or at the track.
- Designed to fit most motorcycle models.
- Maximum Height: 13.25 in.
- Weight Capacity: 1,100 lbs.
- Platform Dimensions: 16 in. x 10 in.
Features:
Specs:
Height | 5 Inches |
Length | 17 Inches |
Weight | 27.6 Pounds |
Width | 11 Inches |
16. MarchInn Electric Car Scissor Jack for 12V DC 3.0T (6600lb) with Wheel Nut Wrench and Wireless Remote
✅Automatic:Work with 12V vehicle power outlet, just plug it in the cigarette lighter and then control the jack by the button, better than the manual scissors, no need to tighten the screw manually to lift the car.✅POWERFUL&EFFICIENT: 3.0T(6600lb) jack capacity, lift the car in less than 2 minu...
17. OTC 1545 Motorcycle Lift
- OTC's Motorcycle/ATV Lift has a 1,500 pound capacity and 17 inch long skids that will lift the largest and widest cruisers on the road
- Lowest clearance available - 3-1/2 inch at lowest level - with a wide lifting range of 3-1/2 inches to 16-3/4 inches
- Removable handle provides 360 degree access to load; T-handle design makes maneuvering the jack easier
- Great features include: foot pedal release, locking rear casters, automatic safety lock, and two ratcheting tie down straps for safety when the jack is in use
- Two-year limited warranty
Features:
Specs:
Color | Silver |
Height | 39.25 Inches |
Length | 20 Inches |
Number of items | 1 |
Weight | 90 Pounds |
Width | 6.5 Inches |
18. XtremepowerUS 300LBS Motorcycle Dirt Bike ATV Motorcycle Bike Scissor Jack Lifts Hoist Mini Crank Hydraulic Foot Operated Lift, Red
- Easy to use foot pedal operation for raising and lowering, compared with the traditional lifting method, it is more labor-saving. As well as include all hardware to mount bike to stand securely
- Lifting up to 300 lbs, the hydraulic scissor floor jack is perfect for tinkering on your dirt bike or small motorcycle
- Lift height from 13-1/2 inches (min height) to 36 inches (max height), the lift table eliminates the need to stoop or kneel while working on your motorcycle
- Wide top platform provides a safe, stable surface for your motorcycle while using the jack. The rubber padding prevents any metal on metal contact, protecting your ride from scratching, scuffing and scraping
- Lift table comes with non-slip hard rubber (gum) plate with strong locking springs to insure safe and sturdy stand. As well as when the platform has been raised to the working height, ensure the locking bar is engaged to prevent accidental lowering
Features:
Specs:
Color | Red |
Height | 36 Inches |
Length | 14 Inches |
Number of items | 1 |
Weight | 25 Pounds |
Width | 16 Inches |
19. Alltrade Powerbuilt 640819 Mechanical Scissor Jack
- 3000 lb, Scissor Jack
- Heavy duty steel frame and saddle
- Oversize base for maximum support and stability
- Working range: 4 inch to 14 inch
- Meets or exceeds ANSI standards
- Heavy duty steel frame and saddle
- Oversize base for maximum support and stability
- Strong construction makes for a durable lift
- Working range: 4 inch to 14 inch
- Meets or exceeds ANSI standards
Features:
Specs:
Color | Black |
Height | 4 Inches |
Length | 6 Inches |
Number of items | 1 |
Size | 3000 lb, Scissor Jack |
Weight | 7.1 Pounds |
Width | 18.5 Inches |
20. Smartxchoices Red/Black Motorcycle Jack Lift Stand 110 lbs Scissor Lift Jack ATV Motorcycle Dirt Bike Scooter Crank Stand (1100 lbs)
- Material:Solid steel construction ;Color:Red and Black; 12 cm removable crank handle
- Two (2) variable screw adapters; Simple crank operation
- Two wings on each side for stability and balance
- Compact dimensions: 18" x 6" x 3.5" (45 cm x 15.5 cm x 9 cm)
- Lifting Range: 3.5"-17" (9-43 cm); Capacity: 1100 lb
Features:
Specs:
Color | #1 |
Height | 3.93700787 Inches |
Length | 20.2755905305 Inches |
Size | 1100 lbs |
Weight | 30.86471668 Pounds |
Width | 13.5826771515 Inches |
🎓 Reddit experts on scissor lift jacks
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where scissor lift jacks are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
I just ordered supplies from Amazon and would love feedback. I decided to go for a scissor jack, though that seems somewhat controversial in the DIY cider press world. The travel is amazing, they are light, cheap and I can operate it with a cordless drill.
Another big question is this 50 quart steamer basket. Cheap, but will it hold up to the strain? I guess the good news is that by going big now (12 gallons!), I can always downsize later.
I'm looking at mounting the disposal in a plastic tub, supported by a wood frame. I'm still working on the design (and will post here, with credit to you knockfer, when its done!).
Finally, instead of the very cool wood drainage platform you made, I'm opting for a simpler cutting board, and will drill a hole and attach a tube for drainage. Still figuring out that detail.
I'd welcome any thoughts about all this, and am so grateful for your inspiration! I'd never heard of using a garbage disposal as a chopper before. My wife is going to love this!
There may not really be a "best". Just different options and their pros and cons may change depending on the work you want to do, the space you have to do it in and the bike you are working on.
There is a version of the front stand that lifts off the center of the triple tree steering stem. This solves the problem of standard front stands supporting the weight of the bike on the forks. You do however need the steering stem to be hollow or at least drilled for the peg of the stand to fit into it. u/TacticoolCanadian links a hybrid stand that does both lifting options.
Strap the bike down appropriately for the end you need to lift. I'm not a wheel chock or wheel vise fan(the one on the Harbor Frieght table in your image is next to useless). I find them annoying and in the way anytime you need to work on the front wheel/suspension. Most all of the mechanics I have worked with over the years have eventually gone to just a angle iron/aluminum stop held in with 2 nuts and bolts finger tight. When I need to pull the front wheel I slide a section of angle under the rear wheel as a stop, add some tie downs to the rear of the bike and slowly release the front tie downs. To save on jacking the front wheel over the height of the stop on the table, remove one of the 2 bolts holding it and pivot it out of the way.
Tables take up a lot of room and can make life easy. In 25 years I've never lost a bike on a table. I know guys who have when mistakes were made. It's much can cause much more damage than a low to the ground tip over off a set of stands. Most DIY home users I see have the most trouble with loading a bike on a table and getting it strapped down trying to do it single handedly. They go for the slow walk up trying to keep the bike vertical and loose too much momentum and can't get the bikes back wheel up the ramp and will try to power through it sometimes getting off balance and the bike falling away from them. Both are easily solved by letting the bike lean into you so it doesn't go over center and pull away from you. The other time is once they get the bike up on it they have to fumble around with holding the bike and strapping it down. This is where some like the self supporting wheel chocks to roll the bike into. Being alone I've found the easiest is to just have a place to set the bike down on the side stand or get it up on the center stand if it has one. I use a platform of two 4x6s and a 2x14 as a table next to the lift to set the bike on the side stand. If you have a Handy lift or the like with wing extensions you don't likely need anything. From there it's just like strapping it down in a trailer.
There are a ton of options for DIY jacks, lifts and tables out there too.
Take a look at www.homemadetools.net/site/search?q=Motorcycle+Lifts&Search=
One of my favorite that can be done cheap is to simply extend one of the motorcycle lift jacks to turn it into a table. I've thought about doing this to add a 2nd part time lift in the garage here at home.
Honestly, I'd just pay the extra $800 and get this one. Or if you've got money to burn and want a really nice flush-mount option, there's this one
It has auto-safety locks every 3 inches, and the hydraulic system is integrated into one of the posts, so there are a lot less exposed lines for potential damage.
The only benefit I see with the one OP has is A) it's cheap B) it's "portable".
But honestly, who's going to be moving a lift like this around every day, and do you really want to cheap out on two of the most important safety and convenience features?
I see what you mean! I was watching this video: https://www.youtube.com/watch?v=EdNdiSMepng and it looked like the same Jack, but I now see what you mean with the bolt holes. Would something like this one be best? https://www.amazon.com/TONDA-TON-Portable-Scissor-Jack/dp/B06Y65M2NS/ref=sr_1_7?s=automotive&ie=UTF8&qid=1537407080&sr=1-7&keywords=car+jack
Or would you get a bottle jack?
Do yourself a favor and get a motorycyle lift. A damn good investment, I assure you. Makes cleaning and maintenance much,much easier. Especially cleaning and lubing the chain.
Having the bike lifted of the ground would be great for winter time storage, as well, as it will take pressure of the suspension and tires; allowing you to avoid getting flat spots on the tires from sitting for a long time.
Plus, bikes looks cool af on a lift.
I live in a 1br in a walk up as well. KangarooCornchips pretty well covered it although I just stick with one good torque wrench, a big adjustable, a cheap Stanley socket set, vice grip, and a flip out hex and torx set. A good JIS screwdriver would be useful too.
Don’t forget there should be a cheap oem toolkit stashed somewhere on the bike, not that it’s enough.
The only thing directly motorcycle related I’ve needed was a cheap jack similar to this
https://www.amazon.com/LiftMaster-Motorcycle-Center-Scissor-Hoist/dp/B01NCT4IKW/
It’s not too heavy to haul downstairs although it is annoying
I’ve been able to do everything from valve clearances to swingarm replacements in my complex’s covered parking lot. The only problem is running back and forth for all the bulky peripheral things like cans of penetrating fluid or degreaser or an oil jug.
Extreme Max 5001.5044 Wide Motorcycle Scissor Jack - 1100 lb. https://www.amazon.com/dp/B0196PAZ1S/ref=cm_sw_r_cp_taa_rGt1Ab1YM58V5
I have this and it works perfectly for me. It lifts the bike tall enough to change your tires and stable enough too. And it's easy to store when you are not using it.
I've got this (Extreme Max Wide Motorcycle Scissor Jack - 1100 lb. https://www.amazon.com/dp/B0196PAZ1S/ref=cm_sw_r_cp_api_KPQEzbC5ZMP4Q). It's been pretty useful for chain stuff and other work I've done on the bike.
However, I got a Triumph center stand from a neighbor for cheap, so the jack doesn't get much use anymore. I'm on a bonneville, but I'd recommend a center stand to anyone. It's very convenient.
I've taken my 390 engine out like 5 times with a scissor lift from Amazon that was like $70 bucks, it's rated up to like 1000lbs or something
Edit: Extreme Max 5001.5044 Wide Motorcycle Scissor Jack https://www.amazon.com/dp/B0196PAZ1S/ref=cm_sw_r_cp_apa_i_dV3PCbWV6FQBJ
Center stand
https://www.amazon.com/Extreme-Max-5001-5047-Motorcycle-Scissors/dp/B0196PAYP0/ref=sr_1_6?gclid=CjwKCAiAh5_uBRA5EiwASW3IasIMFnQo804LL3aB58Yweypspqprui5NqOiEkxn20Mir9FRR-Q6fDxoCs8kQAvD_BwE&hvadid=241914105244&hvdev=t&hvlocphy=9032437&hvnetw=g&hvpos=1t1&hvqmt=e&hvrand=14079434640772928100&hvtargid=kwd-1194916088&hydadcr=24631_10399647&keywords=motorcycle+scissor+jack&qid=1573447187&sr=8-6
$70 bucks now will save you hundreds in shop fees. From changing your oil to pulling your tire to get it changed.
An oil change in your garage using HD supplied oil might run you $35 for oil/filter
And get yourself a shop manual. There is so much you can do on your own with some basic hand tools!
I have this one: https://www.amazon.com/LEAD-BRAND-Scissor-Capacity-Strength/dp/B07CZGTXYH/
It can be cranked up/down with a 17mm wrench or socket, turned with whatever you have in the garage (impact wrench) or whatever you carry in the car (handheld ratchet).
The wrench that came with the jack broke quickly but the jack itself doesn’t seem to have quality issues. However because that wrench is junk you’ll want to consider carrying something else to turn it with... still, it’s a thousand times easier to use even with a normal hand ratchet than the awkward crank bar that comes with most jacks.
Hi-Lift makes adjustable mounts that work well:
https://www.amazon.com/gp/product/B003CEFJ2U/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
I use these to mount mine to my tire carrier (AEV Hardrock carrier) and they work great.
I have this https://www.amazon.com/Extreme-Max-5001-5044-Motorcycle-Scissor/dp/B0196PAZ1S and I'm happy with it. If you go with it buy a 7/8 deep socket and leave it on the stand for easy adjustments
Scissor lift is going to be the most compact for what you're wanting to do, I found this on amazon, its an electric scissor jack for cars thats pretty compact. it uses a 12v power point too, you may already have one in your van that would be easy to use. I just dont know if it would reach tall enough for the clearance you need
https://www.amazon.com/Black-Bull-EJ212-Automatic-Electric/dp/B0027Z6F3W
I bought this one off amazon and it has worked great. It’s compact and inexpensive.
Zeny 1100 LB Motorcycle Center Scissor Lift Jack Hoist Stand Bikes ATVs (#01) https://www.amazon.com/dp/B01860HLCU/ref=cm_sw_r_cp_apip_Vo3KRPVWIXCJz
This is way better, albeit $65, it makes life easy. raise it up until its just below your bike frame, slide it under, crank it 10 times, and you're off the ground. easy peasy.
Tire iron kit,
Bead buddy (helps when taking the tire off), Lift (this has worked well for my KLR, combine with a couple of jack stands for more stability)
Other things that help: rubber mallet, needle nose pliers, SERVICE MANUAL, torque wrenches.
Something like this would do fine: https://www.amazon.com/Torin-T10152-Scissor-Jack-1-5/dp/B004PX8BC2
Not sure how that would work. How would you lift the bike onto the stands? Lifts are relatively low cost and you can get a dedicated one at Harbor Freight or use what I use which is a simple scissor jack. You can certainly get the scissor jack for cheaper since they're quite common. Also check a local auto parts store to see if they have loaner/rental of jacks.
Noted.
Thanks for that info.
Link: http://www.amazon.com/OTC-1545-Motorcycle-Lift/dp/B000OCHCIW
Check out this stand. You can lift the bike up real tall so you can work on it easier
https://www.amazon.com/dp/B0093NMGJI/ref=cm_sw_r_cp_apa_0NVgAb4M15671
I bought this a couple of months ago for a rear shock swap on my Road Glide and it worked perfectly: https://www.amazon.com/gp/aw/d/B0196PAZ1S?psc=1&ref=ppx_pop_mob_b_asin_title
Something like this works fairly well... it's basically a 3/4" hex wrench that fits snugly over the jack:
https://www.amazon.ca/Camco-57363-Leveling-Scissor-Socket/dp/B001V8U12M/ref=sr_1_1?ie=UTF8&qid=1511197626&sr=8-1&keywords=scissor+jack+socket
The lugs are the same size(21mm) and the jack will work, the Prius hasn't gotten much heavier in the past few years. So any tire iron that's 21mm will work, and any jack that is rated to lift 3100lb will work.
However if I had a chance, I would get an aftermarket jack that will be more reliable than the stock ones. This looks like a good option. Hell, put that together with this wrench and you'll be set. Can't get much cheaper than $30 for this stuff.
I have one of these and it works just fine.
What size were the mounts you bought? I found them on amazon but there is a choice between 1- 2 inch and 2-3 inch sizing here.
Remember, they are just stabilizers, not jacks. They just help take out some of the bounce. You can pick up a bit for your drill so you can use a cordless drill for raising and lowering.
https://www.amazon.com/Camco-Leveling-Scissor-Adapter-57363/dp/B001V8U12M/
Oh shit, I read scissor Jack, not Lift. Never mind...;-). Here’s a 7K one,
https://www.amazon.com/dp/B000N4MKM4/ref=cm_sw_r_em_api_c_w9RVAbBCDXHBV
Worth joining the Prime Membership to get the free shipping.
Extreme Max 5001.5044 5001.5044... https://www.amazon.com/dp/B0196PAZ1S?ref=ppx_pop_mob_ap_share
Been using this one....I dig it...
https://www.amazon.com/Motorcycle-Center-Scissor-Hoist-Stand/dp/B00E8HGCEY/ref=sr_1_2?s=automotive&ie=UTF8&qid=1480260820&sr=1-2&keywords=Motorcycle+jack
Torin T10152 Big Red Steel Scissor Jack, 1.5 Ton Capacity https://www.amazon.com/dp/B004PX8BC2/ref=cm_sw_r_cp_apa_W5puzbYSS6Q5W
This'll'do'er
I’m not sure but here’s the link for the product itself: https://www.amazon.ca/MarchInn-Electric-Scissor-3-0T(6600lb)-Wrench/dp/B06XPFXHDK
Edit: motorcycle scissor lift
XtremepowerUS 300LBS Motorcycle Dirt Bike ATV Motorcycle Bike Scissor Jack Lifts Hoist Mini Crank Hydraulic Foot Operated Lift, Red https://www.amazon.com/dp/B00CKY3J3Y/ref=cm_sw_r_cp_api_i_nZHQDb558PD7X
I have one similar to this, but it seems that the kickstand and some other bit is in the way when I try to lift the bike with it, and I don't want to damage these parts ('16 883). Maybe i'm doing it wrong, I dunno, but I couldn't figure out any other way. This is the one I got: https://www.amazon.com/gp/product/B000OCHCIW/
In addition to a scissor jack as suggested by /u/JayNorthpen, get a lug wrench. Often the ones supplied with the car are crap. Either get the kind with folding arms, or just a plain cross type. Here are 2 examples:
Any ladies reading this keep in mind that the weaker you are the larger you want the wrench to be.
Lug Wrench
Folding Lug Wrench
Scissor Jack
Just for off-road. I used to keep it mounted in the back of the Jeep on the roll bar, but it rattled so much I would get annoyed driving on dirt roads. I think I can place a couple pieces of foam into the foot and mechanism to make it quiet, but I just decided to keep it off the vehicle when I'm not off roading instead. Less weight to carry around day-to-day.
Edit: I'll get around to priming it and putting some bedliner on it in the future to match the color. It's kind of expensive for what it is, but most of the jack mounts are $40-$150 so I guess it's within expectations. I liked this solution because I could use it on the roll bar inside or on the bumper. I had previously made some mounts out of u-bolt muffler clamps and wing nuts; those worked but was a pain to get the jack on and off so I gave up and went with this.
https://www.amazon.com/Hi-Lift-Jack-TM-750-Adjustable-Mount/dp/B003CEFJ2U/
You need to get a stand like this: https://www.amazon.com/Smartxchoices-Heavy-Motorcycle-Center-Scissor/dp/B01M3R1JMF
I have one similar (different brand, but it's all the same thing honestly) and the only bad thing I can say is that the rubber feet are kinda shitty. I'll make new ones at some point, but it works to get my Honda Shadow into the air (same problem with your bike, engine sits below the frame.)
Jack it up by the frame rails.