Reddit mentions: The best autmotive led accent lights

OOh, I love working on my existing costumes and trying to improve upon them. This should be fun! To your points:

• 1. The Body Suit: Do as /u/grumpykittyfish said and go for a dyesub body suit. The printed on texture will do a world of wonder for some nice definition. Additionally you should think about creating a muscle under-suit using upholstery (couch) foam. There are a lot of people doing this now with some moderate success, even for beginners. You can go as crazy ripped as you want or just subtle accents to your own physique.
     
     
• 2. The Armor: Have you thought of gluing them to the red suit vs having to button snap them? You'll get a better contouring by doing so. Also, if you can round some of those edges so they aren't so square and add a little weathering to them to give them some depth. You should create an EVA foam cod piece as well to give your underwear some detailing.
     
     
• 3. The Staff: I would start from scratch on this. Using a long wooden or PVC staff, you should create the "Z" out of EVA foam. Carve it, sand it, seal it, and paint it.
     
     
• 4. The Helmet: the glasses thing is a neat idea, but it's probably easier to use an LED light strip, hooked up to a 9v and a switch and you're good to go.
     
     Hope these help, Good luck!

Lighting: I have a tailgate LED strip that does flowing turn signals and blinking brake lights. You've probably seen them around on Wish or Amazon (Not this one specifically, but very similar)

I've got a pair of LED runningboard lights to add that I'm going to wire to Turn Signals and Interior Lights, so when you unlock or open the doors (or turn on the domes) you'll get a courtesy light on the ground.

I've already installed the LED footwells, but havent finished hooking them up yet, just need to ground and plug into the fuse box.

I have the Trailhawk so the exterior lights are already pretty great, I'll probably upgrade the running lights to something brighter to match the headlights and foglights.

I do not have plans to do lightbars just yet... I think it would look too tryhard. What I might do instead is to get one with magnetic bases on either side, or goes on the roof rails so I can remove it if I'm not offroad...running it through the Cigarette Lighter doesn't bother me since it would be in/out temporary.

I'm going to install a CB and run a firestick antenna off the rear tailgate. I have one ready to go... but I'm looking at smaller ones that I can hide all but the handset. I don't have LOTS of use for one, but I'm an 80/90's kid and I HAVE been saved from driving into a Tornado by one before.

The hitch carrier is my first choice anyway, good looking out on the gas mileage.

The Cold Air Intake is partly about the sound (the Tigershark 2.4 sounds a little too...mousey for me at the moment), and for possible fuel mileage savings once I get used to the new sound and don't step on it just to hear it growl.

The Exhaust will probably be a custom job from my dads mechanic. I've known the guy my whole life and just found out he has a "state-of-the-art" pipe bending machine in his new shop and does custom exhausts. I'm looking for airflow (for MPG's) and a new muffler with again... a more meaty, growly sound (without being super annoying).

So much of a list... but I want it to mostly appear Stock unless I'm doing something with the accessories. Thus my wishy washyness on adding a guard to the front end. We definitely have a Whitetail issue where I live and it would be nice to possibly be fine after hitting one instead of having thousands in damage to repair.

I'll redownload Telegram and check that out, thanks!

This is clearly going to take a little bit more research than I expected - my thinking was along the lines of those older LED strips for home use that are basically just plug and play. My experience seems to be pretty outdated!

For the sake of my own curiousity, what's the benefit to going with something like a Neopixel setup over something more like an LED party light like this or this? Assuming solid color and only needing on/off function.

Based on reviews, I'd seen that these are noisy/have coil issues, so is it a safety/longevity thing? Brightness?

I'm all for putting in the work to get a more polished end result that will last longer, I'm just curious from an effort/payoff standpoint. How far down the rabbit hole should I go before I've gone too far for this?

I hope that doesn't come off snarky at all, especially since I'm actually excited to learn how to do this correctly. I'd love to get some crazy Arduino shit going, if not for this suit than for another in the future.

Sure,

I got something like this: http://www.amazon.com/Zone-Tech-Flexible-Waterproof-Light/dp/B00D1ASSY6/ref=sr_1_3?ie=UTF8&qid=1414545078&sr=8-3&keywords=red+led+strips

They're very easy to work with, you can cut them to the length you need and they'll still light. I used one strip per eye, put them in parallel with a single A23 battery and a switch.

If you're trying to avoid soldering that all together which would be ideal, there are some small tube things (can't think of the name) you can buy at radioshack which you feed both wire ends through and then clamp down on it with a wire crimper.

The battery did go in the mask along with the switch, both were housed in in the mouth area and fit pretty easily. A23's are pretty tiny themselves, and you can find pretty minimal battery holders like this http://www.amazon.com/5Pcs-Battery-Clip-Holder-Black/dp/B00ABRQYPM/ref=sr_1_1?ie=UTF8&qid=1414548326&sr=8-1&keywords=a23+holder

Let me know if I can be of any more help!

I have a 2015 LE as well! Got into modding last year. I started with cosmetic modifications and slowly into performance on a budget.

Cosmetic:
- Rubber Front Lip and Sideskirts $12 each side
- Window Visors $42
- Headlight Eyelids $20
- Rear Window Spoiler : $40
- Trunk Spoiler Rubber$15

Electrical:
- LED Foglights $32
- LED Strip Sequential Turn Signals $18
- LED Turn signal switchbacks, requires a resistor and tapping into turn signal wires
- LED Interior Bulbs $6


Performance:
- TRD Exhaust $400 used. Made my car a joy to drive! Other great cheaper options are Borla $350, and J2 $250. I got the TRD for the balanced deep tones and didnt want to be pulled over for 3rd party exhaust ( I live in Cali).
Super budget ebay exhaust is available too! $85 : Sounds decent, join the 11th gen corolla group on facebook to see and hear videos
- Spectre Short Ram Intake $150: Great sound from engine and increased torque
- Megan Racing Rearsway bar $110: If you like hugging corners while turning this does wonders for reducing bodyroll. I have way more confidence on tight turns!

I got this kit from Amazon.

It comes with 4 led strips, and fuse taps for a couple different sized fuses, along with an led controller, full function remote, as well as keychain remote. Hands down the best value I could find.

Wired up the fronts a few months back, but didn't have time to do the back seat along with the fronts (with 2 kids there isn't much time for anything)

To power: fuse tap on the drivers side fuse panel to F17. Ground to the bolt that is right in that same area. I also tucked the controller away in that same location with some 3m double sided adhesive.

Lights: drivers side was easy. Figure out where you want the lights (helps to plug them in and have them lit up so you can mess w placement til you find what you like) then 3m/zip tie/etc to the spot. Passenger side: I popped off the center console trim and ran the wires across that to reach passenger front foot well. Same thing...mess with placement, when good, attach.

For the backseat: pulled out rear seat cushion, and trim along the drivers side rocker panel up to the fuse box. Zip tie the cables together, and run along the channel that's right there, then along the front of the rear seat area just behind the cushion. End of the wiring terminates in the middle of the seats just behind center console. Put rear seat back in, climb back there and plug in led strips to find placement. Used a few dabs of hot glue to attach them to the bottom of the seat.

And that's that. This kit is so simple that it is really a painless install, you just gotta make sure you run the wiring neatly, and secure it along any runs to either the dash, another wire loom, etc, so it doesn't fall out. Tuck the excess up into the fuse panel and call it a day!

I found [these](OPT7 Aura Smart-Color LED Strip Interior Lighting Kit (4 Items) https://www.amazon.com/dp/B00OU5LOT2/ref=cm_sw_r_cp_api_VBjDybYB1D1R2) and I think I'm gonna pull the trigger. Out of all the kits, these have the best reviews and they come with a fuse attachment you just plug into the fuse box to have them on with ignition, etc. I was looking and apparently I can remove the panels to the side of your legs (right leg for driver and left for passenger) pretty easily and just run the wire through and then close it back up. Plug into the fuse box and done. They have some stupid sound sensing stuff, but you don't have to use it. You can steady any color, strobe, dim, or cycle through etc. Just a thought, but from what I've looked into for myself, these seem the most hassle free. I have a link to the workshop manual that explains how to remove these panels, but it's for a 14. But, I imagine those center panels didn't change much. Let me know if you need it. I'd have to get it from my laptop for you.

Forgot to mention, I have to get one with a dimmer. I tested if I would even like illumination so I bought a. couple of stick on LEDs and stick them in my footwells and it's pretty distracting, so I may end up running them only to the door being opened. Anyway just a thought if you're not 100% sure you want them, you can grab those stick on LEDs for like $2 to test it out first.

Car Interior Lights - 7 Colors and Multiple Patterns for Front & Back Underdash Decoration Lighting - 12v - Super Cool Music Rhythm & Sound Activation Function - Make Your Next Drive Fun & Exciting https://www.amazon.ca/dp/B01JMBRA64/ref=cm_sw_r_cp_apa_OLDkzbC8D55QV

I just wired it into the glove box lighter. Took 20 mins to install. Just peel and stick. I suggest turning the lights on when running it behind the dash. Makes it easy to fish them through!

It's really, really easy to add your own ambient lighting to the Focus (or any car really). Most LED strips are already 12v. They'd need an adapter from house wall power but in a car (the vast majority of them anyway) the 12V circuits are already there! If you're concerned about your own electrical knowledge they make kits too; they're pretty inexpensive and you could splice open that cigarette adapter line to wire it in directly or get something like this. Personally I'd buy my own strips, controllers, and hard wire it though (make sure you confirm controller works with your strip). Since you're in the footwell I'd also recommend weatherproof but it's not super necessary since it won't be directly exposed.

You could tap in to an accessory line/fuse to have them always on or get fancy and wire them in to the dash lighting for when the headlights are on so that they only come on at night. I just used these fuse taps the other day for a dash cam and radar detector install; make sure you have the right fuses for your install though. I had to pickup some lower amperage ones to properly protect my lower amperage gear.

Some LED strip lighting is easy to adhere or screw down depending on your preference and you can even get RGB and an IR/RF/bluetooth controller to customize.

Anyway, the whole thing should take nothing more than an hour or two and less than $100 in parts.

Hello! I hope you find these as cool as I do! I think it'd make any car look awesome!

And hmm, for me?! I'd love this! My computer only has two... :/

Oh! Vroom Vroom!!!

I went with this from Amazon and besides the trunk LED, I like it. Dome/map lights are very bright and I love the nice white appearance against the leather.

I too was looking into this. Look at mrcycles.com for the parts breakdown of the light. My though was to remove everything, make an elongated "Z" more like two "L"'s and mount that to the bike. The light with the original bolts and the plate below laying almost horizontal. For the LP light I was going to stick one of these under the taillight. Prewired Surface Mount LEDs (2835, Cool White LED) - 3 Pack https://www.amazon.com/dp/B01ENC1SXI/ref=cm_sw_r_cp_tai_lf4QybCW4WPF4
Which I used on another taillight mod for the LP light and it worked perfectly.
The next hurdle would be the signals. But tabs could be bent from or welded to the "Z" bracket and holes drilled for the signals.
Another option. The DRC bracket is available alone for about 30.00 from 12oclock labs and the stock taillight could probably be easily attached to that.
But just slicing it off like you said and a small bracket would probably work too.

I'm a little bit hood when I'm working at home, lol. I have some of these little offroad lights (maybe not those exactly, but similar). I ran some wire with alligator clips on the end so I just hook them to the car battery. They last for-freaking-ever on that big battery, and they're pretty bright. I attach them to little countersunk magnets so I can stick em just about anywhere, like on the hood of a car. In the winter I stick them on the ROPS on my little tractor so I can putter around before sunrise/after sunset and move snow (if it ever snows again).

Orange cat claw protectors, Orange lubricant!, Awesome office stuff! - You Need that!, gummy lap, Lighttt. Hope you find stuff you like! Oranges are delicious !

I purchased this and installed myself in the first month of owning:

OPT7 Aura Smart-Color LED Strip... https://www.amazon.com/dp/B00OU5LOT2?ref=ppx_pop_mob_ap_share

Very easy install and looove the added light (red/blue are my most common) while driving at night. Conveniently, you can change it on the fly to fit your mood! I installed all 4 strips, one for each floor well, wires are all hidden, and came with a relay tap so no need to bother with hard wiring or using a 12v other adapter 👌

[edited for spelling]

URGENT here. Get your engine pressure tested to make sure it is not a blown head gasket. I own a 2006 volvo s40 t5 AWD. And I had misfires out the ass for months and I finally found it it was the head gasket. Luckily I know a volvo mechanic personally and he did the head gasket repair for 2,500$. But before you do that I would take each coil and look to see if there is any evidence of arcing (a sort of burnt coloring on the side) that also may cause misfiring) as for cosmetics I put a whole new stereo system in my car including a head unit in the glove box so I can play my own music. Plus I put all new alpine speakers in each door and ran power from the firewall (located behind the glove box) to the trunk for 2 subwoofers. I also put color changing led lights under the dash where the driver and passenger sits, and in the back seat. It pulses to the music http://www.amazon.com/dp/B000I04Z7Q/ref=cm_sw_r_udp_awd_FPM4tb13FSX2W . People love it. You can only do the head unit replacement if you don't have the center speaker in the dash( because its all fiber optics). I put new rims on it. And dipped them. I also blacked out my tail lights and spaced out my letters. Heres a picture. http://i.imgur.com/3xEReGG.jpg
I hope this helped. :)

Ok, thank you so much for your help! I bought these yesterday. Do you think these will be fine? https://www.amazon.com/gp/product/B00D1ASSY6/ref=od_aui_detailpages00?ie=UTF8&psc=1

Sure!

• Takeda Air Intake (made for Legacy, but fits fine): http://afepower.com/afe-power-tr-4303p-takeda-stage-2-pro-dry-s-cold-air-intake-system
  
• Subimods Hella Horn Combo: https://subimods.com/hella-sharptone-horn-combo-w-subimods-bracket-and-v2-wiring-harness-2012-2014-impreza-n-a-2013-2016-crosstrek-2014-2016-forester.html
  
• Rally Armor Mudflaps: https://subimods.com/rally-armor-ur-mudflaps-black-urethane-grey-logo-2013-2015-crosstrek-xv-mf26-ur-blkgry.html
  
• Colin LED Tail Lights: http://www.thespeedline.com/colin-11-12-13-14-15-16-subaru-xv-crosstrek-impreza-sport-wagon-hb-led-tail-lights-oem-red-lens-chrome/
  
• Rally Innovations Light Bar: https://www.rallyinnovations.com/collections/rally-light-bar/products/2012-2015-subaru-crosstrek-xv-rally-light-bar
  
• OPT7 12" LED Light Bar: https://www.amazon.com/gp/product/B00KJ189EE/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
  
• Bull Bar Nudge Bar Mounts: https://www.amazon.com/gp/product/B013EVYQKG/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
  
• Yellow Fog Lights: https://www.amazon.com/gp/product/B014EJRNQG/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
  
• LED Interior Lights: https://www.amazon.com/gp/product/B00I2I24Y2/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
  
• Subispeed F1 Style Rear Fog Light: http://www.subispeed.com/subispeed-f1-style-rear-fog-light-2015-wrx-2015-sti#.Vs8b1JMrIUE
  
• Nameless Exhaust Muffler Delete: https://shop.namelessperformance.com/axleback-exhaust-2013-subaru-xv-crosstrek-impreza/
  
• Subispeed Beatruish Tow Hooks (2):http://www.subispeed.com/2015-subaru-wrx/shop-by-manufacturer/beatrush/beatrush-front-tow-hook-2015-wrx-2015-sti
  
• Weather Tech Floor Mats: https://www.amazon.com/gp/product/B00IIF8O2K/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
  
• STI Wheels 17" (Came with the car)
  
• Thule Canyon Basket: https://www.amazon.com/gp/product/B00R6SBH6K/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
  *Thule Aeroblades: https://www.amazon.com/gp/product/B00KPYA2UY/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
  
• GetSomePass Fairing (Replaces the Thule Fairing): http://www.getsomepass.com/shop/thule-canyon-basket-fairing-replacement
  
  Hope that helps!
  

i just installed an opt7 aura kit, the control has an optional wire to hook into the dome light, i think its what your looking for.
for 45$ its pretty great, colors are quality the adhesive & kit is complete, just don't get psyched when you see the music matching button.
https://www.amazon.com/OPT7-Smart-Color-Strip-Interior-Lighting/dp/B00OU5LOT2

They also sell an underglow and wheelwell kit that i recall someone mentioning that they could be controlled together...

Thanks! I'm using some cheap LED strips from Amazon and are surprisingly holding up well for what they are. Here's the link https://www.amazon.com/gp/aw/d/B07DJ8N8CH/ref=sspa_mw_detail_3?ie=UTF8&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUFLRkVSWThOT1A4VVgmZW5jcnlwdGVkSWQ9QTA5MDIxMTcxVzFWRkVKUVJLVjQ3JmVuY3J5cHRlZEFkSWQ9QTAxNTk3NjhMRFVTMDIzVEhKOEEmd2lkZ2V0TmFtZT1zcF9waG9uZV9kZXRhaWwmYWN0aW9uPWNsaWNrUmVkaXJlY3Q=

https://www.amazon.com/gp/product/B07G9G46CC

Super cheap stuff from China. It came with a 12v cigarette adapter, and a USB adapter so you could easily power it from a USB battery bank if you just wanted to do this temporarily without bothering to wire things up in the car.

I put this kit into my 05 in like 20 minutes and it looks awesome! Ran the wires through the center console and spliced into cigarette lighter wire for power.

http://www.amazon.com/LEDGlow-4-Piece-Interior-Underdash-Lighting/dp/B000I04Z7Q/ref=sr_1_1?ie=UTF8&qid=1456898325&sr=8-1&keywords=Led+footwell+kit

Megulla Truck Bed Light Strips, LED Truck Bed Lighting Kit with On/Off Switch and Fuse -Super Bright LED, IP67 Waterproof -for Trucks, Trailers, Pickups, RVs, Vans and Cargos (Cool White, 6000K) https://www.amazon.com/dp/B0711FYXSM/ref=cm_sw_r_cp_apa_i_lCmQCbW55XR8S

Recently used these for an outdoor event. They are perfect -- they look just like flame until you get really close.

I did the LED kit on my 07' interior just a few months ago. When you do all at the same time if really cleans up the look at night and definitely adds more light.

Ever sat in a new truck from the last few years? LEDs galore. It's kinda like that. Really just refreshes the look and feel of the 1st Gen Ridgy.

There are complete kits on Amazon.

Edit - [here ya go ](http://www.Honda.com/ Ridgeline LED Package... https://www.amazon.com/dp/B00GSZQ8NE?ref=ppx_pop_mob_ap_share)

These are the lights on the interior. They come with an adapter for a car charger / cigarette lighter, but if you want to wire it to your fuse box, which I recommend (much cleaner looking), you need to buy a fuse tap.


To use a fuse tap, the positive (red) wire connects to the tap and the negative connects to the ground of the car battery. It should come with basic instructions, though.

Here are the lights i got just in case you guys want to check them out. Not bad at all! Very bright!

I added some extra footwell/under seat led's recently. It was super easy, just time consuming and can be annoying if you're a bigger guy/gal. I'm 6' and had a little trouble bending in strange ways to get into the pedal area to mount the box and one of the lights, as well as connect the fuses. It was then super easy to pull off the center console siding and run the cables into the back and across to the passenger side. I think it looks great. There is about 2" of visible cable in the back to account for the seats moving back and forth, but other than that I installed then in about 2 hours with no problems.

I used [this] (https://www.amazon.com/gp/aw/d/B00OU5LOT2/ref=mp_s_a_1_2?ie=UTF8&qid=1496207734&sr=8-2&pi=AC_SX236_SY340_QL65&keywords=opt7&dpPl=1&dpID=51s2zulxQbL&ref=plSrch) kit and I'm impressed with the build quality and everything else. The only issue is that you'll need to get a micro fuse adapter and either solder it or splice it into the power cable.

I'll update this post with some day and night pictures tomorrow night.

You commented on one of my comments about 9 days ago, and here is a link to the lights I was thinking about getting. I was considering running the wiring to the cig charger in the center console, and ask my engineer friend for a way to hide the wiring so it goes shines on the floor at a dim brightness (these can adjust brightness), and have it fade between colors.

As for the cig charger I was going to get a splitter so I would have 1 of 4 occupied by the floor lights and then the 3 left open.

I just need to figure out whether the cigarette lighters turn off when the car does, so I know whether I can leave it plugged in or if I will have to keep unplugging and plugging it in accordingly.

http://www.amazon.com/dp/B017JPW6IC/ref=wl_it_dp_o_pd_nS_ttl?_encoding=UTF8&colid=1SLIL6D5YGAYP&coliid=I1ZSV7Q64N1QRE

Thanks man, i used DRL leds from Amazon.

Here’s the link: CARLITS 2 Pcs 24 Inch Flexible... https://www.amazon.com/dp/B07K7F7KRS?ref=ppx_pop_mob_ap_share

I have these in my TLX
Unifilar Car LED Strip Light, MINGER APP Controller Car Interior Lights, Waterproof Multicolor Music Under Dash Lighting Kits for iPhone Android Smart Phone, Car Charger Included, DC 12V https://www.amazon.com/dp/B0798KMJFG/ref=cm_sw_r_cp_api_i_ak0VCb7PDC0D5

I got everything off of amazon and installed everything myself

fogs: Sirius COB LED Chip 8000 6000k Lumens https://www.amazon.com/gp/product/B06Y65Z3YZ/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

Reverse Lights: JDM ASTAR 800 lumens 921 912 PX Chipsets LED https://www.amazon.com/gp/product/B00K3GBRQ2/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

Headlights: Stark Korean CSP LED Chip 6000k Lumens
https://www.amazon.com/Korean-Chip-8000LM-Headlight-Conversion/dp/B01LFV49P4/ref=sr_1_1?ie=UTF8&qid=1502221037&sr=8-1&keywords=korean+chip+9012

Interior Lighting: https://www.amazon.com/gp/product/B000I04Z7Q/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Daytime Lights and License plate Lights:
https://www.amazon.com/SiriusLED-Extremely-Chipset-Interior-Courtesy/dp/B00GXO3IUG/ref=sr_1_4?s=automotive&ie=UTF8&qid=1502221227&sr=1-4&keywords=license+plate+lights

I used these from Amazon.

CARLITS 2 Pcs 24 Inch Flexible Dual Color LED Headlight Surface Strip Tube Light

https://www.amazon.com/dp/B07K7F7KRS/ref=cm_sw_r_cp_apa_i_qyWGDbG4GDG9S

This is what i got for my 2016, it cost like $20 I think.
https://www.amazon.com/dp/B00IGQS2SC/ref=cm_sw_r_cp_apa_xmxqybYZDZSBK

If you got a detolf, you can buy these lights and stick them one per shelf.

I'm using mine like this.

Also now you don't need to solder.
These lights come with a little strip to connect more lights together.

Amazon has affordable kits with mostly good reviews. I haven't gone this route my self so I can't speak personally to the quality. Here's one kit I found but there may be others if you search around.

http://www.amazon.com/LEDpartsNow-Crosstrek-Premium-Interior-Package/dp/B00I2I24Y2

Here's the strips.

CARLITS 2 Pcs 24 Inch Flexible Dual Color LED Headlight Surface Strip Tube Light White & Amber Daytime Running Light Waterproof,Decorative Lamp,Running Light,Neon Lights,Turn Signal Light https://www.amazon.com/dp/B07K7F7KRS/ref=cm_sw_r_cp_apa_i_OaBuDbZ81VS1Q



And I use a couple of these to make disconnects

https://www.oreillyauto.com/detail/b/towing-solutions-3935/accessories-16449/truck---towing-16781/trailer---towing-16648/trailer-electrical-16828/trailer-wiring---universal-16683/2-3-4-5-way-flat-connectors--wiring---accessories-18813/a068db1e7613/hopkins-towing-solutions-wire-adapter/48145/4379658?q=trailer+plug&pos=66

Aftermarket. The OEM parts were too expensive for my wallet.

Footwell lights: https://www.amazon.com/gp/product/B00OU5LOT2/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

Door Sills: https://www.amazon.com/gp/product/B07S7M3FC1/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

Here is the mobile version of your link

Here you go.

I have a '16, but I got the interior lights from Amazon.

https://www.amazon.com/gp/aw/d/B00IGQS2SC

If you can change a light bulb, you can change these out.

it is custom..but very simple...kit from Amazon.https://www.amazon.ca/gp/product/B07K7F7KRS/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
Wrap with headlight tint or Spray...I wrapped but the spray would be simpler...3m taps and 3m double face tape to attach to splitter

Links to components used:
Headlight
Wiring Harness
36v-12v Converter
Tail Lights
heat shrink
Mounting Brackets

Link Here ya go

It's this kit

What interior LED lights did you get from amazon? I was looking at a few for my 2019 Limited Crosstrek

https://www.amazon.com/SiriusLED-Extremely-Chipset-Interior-Courtesy/dp/B0186P1MUW

https://www.amazon.com/LEDpartsNow-2013-2018-CrossTrek-Accessories-Replacement/dp/B00I2I24Y2

https://www.amazon.com/Subaru-Forester-Interior-Crosstrek-1998-2018/dp/B06X9S4Q4Y

https://www.amazon.com/SEALIGHT-Chipset-Interior-Courtesy-License/dp/B07G4VJP5N

Haters gonna hate bro! I get it man I get it.

Installed a customized million color led bar in my truck. Turn the lights on red to drive at night with full visibility inside and out. When the sun starts coming up turn the lights to blue.

http://imgur.com/a/VKo5z

http://www.amazon.com/Multi-Color-Color-Interior-Underdash-Lighting/dp/B000I04Z7Q/ref=sr_1_2?ie=UTF8&qid=1396655302&sr=8-2&keywords=led+lights+million