1. For that kind of riding, you got a good enough bike. Heck, you could have gone tiagra and would have been ok. The parts will last you a long time so you won't have to worry about upgrades in the near future.
   
   
2. If you haven't yet, learn how to adjust the front and rear derailleurs yourself. It "literally" takes 1 minute or less to do. People don't learn and end up paying constantly when they take their bike into the shop for a "tune up".
   
   Learn how to adjust your brakes. Again, takes 30 seconds to learn and you can do it within 10. All you need is a hex wrench (probably 5mm).
   
   Learn how to clean your chain. It's easy to just put the bike up when you're done, but wipe the grime off your chain RIGHT AFTER the ride. Doing this keeps it down to a lower amount and reduces wear. Also, remember to wipe the cogs in the rear derailleur when you wipe the chain too.
   
   I would suggest buying a towel and a few rags dedicated to this. The towel to cover the floor (if you do it inside) and rags to wipe off the bike. If you have a hose that always helps. I don't.
   
   But if you get the bike wet, wipe standing water off. The bike is resilient but rust creeps in over time and ruins the look.
   
   
3. I would suggest buying this:
   
   http://www.amazon.com/Stanley-85-753-Piece-Long-Metric/dp/B000NIFJQE/ref=sr_1_1?ie=UTF8&qid=1398374834&sr=8-1&keywords=hex+wrench+set
   
   I got it and it's awesome. Lets you do virtually all maintenance sans BB removal and wheel truing on your bike. Seriously; you'll use the 4/5mm the most, and possibly the 3mm.
   
   Get a floor pump for your house and grab some CO2/nossile for flat repair.
   
   I normally carry 1/2 tubes, 2 CO2 canisters, 1 CO2 nossile, tire levers (you might not need those) on my ride in my jersey pockets. You can fix a flat in 5 minutes; no hassle.
   
   So I would say now, to buy 3 tubes; 2 or one to carry with you, and one for a backup so you aren't left with a low number should you flat one day and need/want to ride the next.
   
   Some people patch but I dont' flat enough to sweat 6 bucks a tube.
   
   
4. Save for new tires down the road. Ride those until you get constant flats, then get yourself a pair of Continental GP4000Ss (if you want performance oriented) or Gatorskins (if you ride over a lot of glass)
   
   Those GP4000s tires are some of THE BEST tires you can buy right now for speed/durability/grip in wet/dry conditions. They really are magical.
   
   
5. A jersey with pockets is awesome. Get one. It doesn't have to be something fancy, but anything will be better than a tech T shirt. What I do is
   
   Left pocket: Phone/ID/CC/Keys in a zip lock bag. Protects from rain and sweat.
   
   Middle pocket: Tools/Tire levers/Gels/Chews/Food
   
   Right pocket: Tubes
   
   I actually have a storage bottle on my bike under the seat, so all of that goes in there; I just stash food and stuff in the back pocket now.
   
   Also, if you get cycling shorts, and you should, you can put gels under the shorts on your legs for easy access and space saving.
   
   
6. It "might" get expensive up front if you buy jerseys/shorts/pump/stuff all at once, but you'll only have to make that purchase one time.
   
   In the past year, I've spent 100 dollars on bike maintenance stuff. That's on new tires. For stuff I needed anyway.
   
   Lube lasts a long time, bar tape lasts a long time, quality gear lasts a long time.
   
   
7. Learn some awesome new recipes for cooking. You'll want to eat healthy/healthier if you aren't, so look up some great dishes. Fish is awesome. Protein, tastes great, and pretty cheap if you pair it with other things. Swai tastes great with pasta and Talapia is awesome for a different overall taste palate.
   
   
8. If you have any questions, feel free to ask. CO2, jersey recommendations, pricing, food, gels, maintenance, anything.
   
   
9. If you aren't the type to just dive in with tinkering, swing by a local coop or bike shop if you have one near. Just go in, ask somebody how to show you how to adjust something, and 9/10 they'll be happy to help.
   
   The thing about bike maintenance is, it's kind of intimidating at first, especially if you're adjusting something and you don't "really" know what you're doing, but the physics are simple, and it's just a frame and parts held by tension on wires and some gears. Very simple.
   
   If you get something changes/adjusted by somebody, try and stay and watch. Or, hell, ask to help. I had to recable my bike last month and just asked to help the guy to do it. Ended up taking a bit longer but I know exactly how to do it on my own now, and it cut the cost of 60 (which is on the low end, actually) to 30.
   
   Last thing, I wouldn't worry too much about bottom bracket and wheel truing now; that requires special tools and isn't easily done without them. If you can afford to have that worked on, that's ok. (And those rarely need looking after, like once a year if you don't trash your stuff).

As I stated elsewhere I don't think a torque wrench should be on the top of the 'recommended tools' list, esp if you just plan on doing routine maintenance. They are definitely good to have once you start tackling larger projects but a good torque wrench can be quite expensive and I think that money is better spent elsewhere when first putting together a tool set for routine maintenance.

I'd recommend:

• jack & jackstands
  
• a decent socket set. I personally have this set and it has proven to be a good starting point that I then built off of as I needed other tools (including said torque wrench, etc). I've owned & used smaller sets as well but for the extra $50 or so that it costs to step up to the 255-piece set I think it's worth it.
  
• Good ratchets - While the craftsman ratchets themselves will get you by I'd also recommend a better set of ratchets if you plan on doing frequent work. I got these and absolutely love them, my buddy likes them enough that he is buying a set now that he has used mine.
  
• Ratchet wrenches are unnecessary but a nice luxury. I got Gearwrench ratchet wrenches for 50% off during the annual Xmas sale at Advance Auto parts so I'd say to wait for that if you can.
  
  Edit to add:
  
  
• Tire iron
  
• Threadlock blue for reassembly
  
• MAPP gas torch (can get them for like $40 at Home Depot IIRC... VERY useful for stubborn nuts/bolts).
  
• If you do plan on tackling larger projects it might also be good to get a breaker bar for extra leverage on said stubborn nuts/bolts, though this also introduces more risk of breaking bolts).
  
• If you do end up breaking bolts, it's always good to have a decent drill and drill bits

For tool boxes, I'd go craigslist, 100%. Get in the habit of looking for toolboxes twice a day, and you'll find a good deal eventually. I'd also recommend buying power tools on CL, especially corded ones (where you don't have to worry about a worn out battery). If you want to buy new, the harbor freight tool boxes are a great deal and work really well.

As far as tool sets, I've found it better to kinda just accumulate the stuff you need over time. To start, definitely get a good socket set with 1/4" and 3/8" drive sockets, as well as a couple ratchets. I'm partial to the composite bodied tekton ratchets on amazon, as it's great to not have to worry about dinging the paint by swinging a ratchet into it. I'd also reocmmmend getting a set of gearwrench ratcheting wrenches. They're phenomenal, and once you go to a ratcheting wrench you'll never go back.

As far as other tools, you can't go wrong with a big hammer, a set of pry bars, and a good screwdriver set. It's expensive, but the chapman manufacturing bit driver sets are incredibly well made and super versatile. It's not cheap, but it's also essentially the only screwdriver set you'll ever need. A good impact wrench can be very helpful for general use, though I'd recommend getting a set of impact-rated sockets to go along with it (the 12-point sockets in most socket sets can strip quickly when used with an impact).

Also, buy as much lighting as you can, and get something comfortable to sit on. Trust me, you'll thank yourself later.

I got my first automotive job about 2 years ago. I am also a nut at buying tools. I started off with an 8-drawer Cornwell cart. Loved it. Once I got a decent amount of tools, I bought a SO Classic 96 box. Worst decision ever. Granted it was a fantastic box. But for $6000? No. I was paying about $200/mo (my minimum payment was only $38/week but I wanted to put more down)... the interest rate... 22% which I was told was average. I cant tell you how stupid I felt seeing that, out of that $200/mo, $60 was going to a finance charge. I paid until I got down to owing $3,500, bought it completely with a credit card that I got 18/mo-no interest and then sold the box for $3,000 cash. I took a $500 hit, but it sold after 3 days and I wouldve paid more than $500 if I kept paying to SO.... I went back to the cornwell cart for about a year and realized that SO and their interest rates suck and I really didnt need that box at that time. I just bought a used Cornwell 58" box with a hutch for $4,500 (normally $9,000 brand new. Got repo'd from some guy that stopped making payments. Don't be that guy) at 9% (lowest they got) and sold the Cornwell cart to a coworker for $500. Couldnt be happier.

The ONLY hand tools that are absolutely a must from SO, are their ratchets, pry bars and cordless ratchets. Best out there, no doubt about it. Get long flex head ratchets

For sockets/extensions, Gear Wrench. You can get shallow and long metric sockets from your local Advance Auto Parts from a pretty good price. Gear Wrench also makes Torx and Hex (allen) sockets.

For wrenches.... Gear Wrench or Cornwell. Also, these are my favorite... http://www.amazon.com/ATD-Tools-99650-Ratcheting-Wrench/dp/B008FXN0VK

Deep Impact sockets, Harbor Freight. Seriously, they are impact sockets, they rarely break and youll be chucking them on the ground to loosen a bolt that got stuck. No need for anything fancy. I dont really see the need for shallow impact sockets

For pliers, Knipex Knipex Knipex... You will thank me later. Snap On prices, but 10000X better quality. Snap On pliers suck ass and wont warranty the teeth on them. Knipex does warranty the teeth. Just look at their needle nose pliers... every tooth on them lines up perfectly (point to point) with each half. Their long-handled Wire cutters are awesome and their channel-lock-style pliers just bite harder the more pressure you apply when youre breaking something loose. Ze Germans might make shitty cars, but they do know how to make quality tools.

For cordless impact tools, Ingersoll Rand. Pricey, but they are the best out there. I have the 1/2" and 3/8" IQ 20V series. Little secret. Look for when they run a special on the 1/2" impact that comes with a charger and 2 batteries. The 1/2" impact batteries also fit on the 3/8" impact so you can save some money and just buy the bare 3/8" impact tool. The batteries for the 1/2" are 3 amp while the 3/8" are 1.5 amp but the 1.5A batteries wont work on the 1/2" impact.... sorry if that was hard to read.

I know that having the Snap On name stamped on everything you own is every new mechanics dream. Been there, regretted that. So much money wasted. Snap on USED to make the best of the best and SOME of their stuff still is the best. But they have gone down hill and more and more of their tools are made overseas now. Granted, some overseas made tools are actually top notch. Youll never be able to convince anyone that, but its true. A guy at my shop has a ton of older Snap On stuff and works just fine. But every time one of his 20 year old tools breaks, he gets upset. SO still warranties it, but then he has to keep getting it warrantied because the quality isnt there anymore and they keep breaking.

Start small, avoid too much debt, and fuck SAE sizes except for 7/8". I dont think car manufacturers use them any more

Here's an old post I had from /r/homeimprovement regarding a new home, hope it helps.

• Clean the gutters immediately and make sure the downspouts are feeding water AWAY from your foundation and down grade.
  
  
• Clean every single drain and make sure there is no hair clogging any of them. Especially since you just bought it and it's probably not even your hair. Don't just use drain-o, get down in there with one of these.
  
  
• Clean literally everything you can. Shop vac the basement/attic. Get the ceiling fan blades. Clean the kitchen cupboards and drawers. Dust all of the woodwork especially above doors and windows.
  
  
• Clean the windows and not just the glass. Get the window jambs and sills.
  
  
• Make sure the weatherstripping on all doors and windows is intact and seals well. If there isn't any, get some.
  
  
• Clean the dryer vent.
  
  
• Get the heating/cooling system cleaned. Boilers and furnaces are notorious for never being maintained until there's a problem and if you have an AC unit it will operate much more efficiently if it's clean.
  
  
• If there are appliances included, pull them out of their normal position and clean the shit out of them.
  
  
• Change all the lock sets, who knows who has a key to your house.
  
  
• Get a pressure washer. Don't skimp and get a cheapo electric you'll just regret it when it come time to clean anything besides a car. Clean your porch, decks, sidewalks, driveway. Seal your concrete after as well.
  
  
• Get quality yard maintenance tools. When string trimming or using a leaf blower I want to spend as little time possible doing it and not fighting to get the thing started. Check out the Echo PAS system, it's pretty damn good IMO and has a great consumer warranty. The Honda HRX lawn mowers are fucking fantastic, get one with the synthetic deck.
  
  
• If it snows where you live, get a quality snowblower. I will never in my life NOT be without one in the winter.
  
  
• Meet your neighbors, introduce yourself and your pets, if applicable.
  
  
• Make sure all your house numbers are CLEARLY visible from the street and make sure your mailbox doesn't leak.
  
  
• Buy a plastic deck box for package deliveries if you don't have a decent porch to keep that shit out of the weather.
  
  
• Get a basin wrench. It's so fucking worth it when you need to fix anything sink related.
  
  
• Replace the shower heads with something you like.
  
  
• Edge your sidewalk and driveway, it looks a million times better even if it's not in great shape to.
  
  
• Replace the rubber washers on your hose bibs.
  
  I'm sure there's more, but it's midnight and I'm sleepy.

I own that Joker set. They look cool. They've got a feature list a mile long. But my Tekton wrenches are just... better. For what it's worth, the quality on the Joker's aren't even that good. Wera sent their manufacturing for the Joker's out to the Czech Republic, which is kinda like the China of Europe for cheap manufacturing.


If you need ratcheting wrenches, I'd recommend you get the Tekton WRN53170 set. 8-19mm with no skips, which is the same range as the wera plus the 9mm. And the set is only $80 for some strong wrenches with better quality control than the Joker's. Great warranty too. https://www.amazon.com/TEKTON-WRN53170-Ratcheting-Combination-Wrench/dp/B01F511TS0


If ratcheting isn't that important to you, the WRN03393 set is also great. 8-22mm with no skips. Only $50 bucks. https://www.amazon.com/TEKTON-Combination-Wrench-Roll-up-Storage/dp/B0199R9UQ4


Oh and always buy the Tekton sets with the pouches - if you like the plastic wrench organizers instead, you can always buy those separately for a few bucks, but those roll up pouches are gorgeous and strong and you can't buy them by themselves.


Anyway, sorry if I sound like a Tekton fanboy, but I own all three sets I've talked about here. I hardly use my Joker's because the Tekton sets are way better. TL:DR Jokers not worth it.

1: You seem smart enough to realize what you need to do to get to where you want to be. Many aren't that lucky, or that smart.

2: Don't focus on the time spent at work, focus (and treasure) the off hours that you can spend doign what you love and with those you love.

3: Set a picture of your family nearby, or on your phone. Look at them when things get to be too much. They need you, and if your biggest sacrifice for them is being bored, you're lucky. Think about them, and how much you love them, and how much they love you. And on your days off, spend as much time with them as you can. A year and a half is nothing, you can do this.

Linky.

I just put together a tool kit for my BRZ, and I ended up getting a set of Tekton metric sockets and a Tekton low-profile 3/8s inch ratchet. I've used Tekton quite a bit and I found them to be pretty great. These metric sockets will cover just about everything on the car that can be loosened or tightened with a socket, and since they're deep sockets you can loosen lug nuts with them.

I'd suggest getting a breaker bar or torque wrench if you want to get an additional accessory. The breaker bar is great for loosening tough nuts, and the torque wrench is terrific for tightening a fastener to the exact amount of force it specifies in the manual.

If you really want to go above and beyond, an open ended wrench set (also metric) can be great for when a socket just won't fit. They even make a version with a built-in ratcheting mechanism

In summary, a metric ratchet set that goes from about 8mm to about 20mm is a great gift idea, and you can easily add on other accessories or wrenches if you want to make your gift a bit bigger. I can personally vouch for the Tekton stuff--sure it's not the most expensive fancy set of tools out there, but they look, feel, and work well.

Hope this helps!

I think your heart is in the right place, but I honestly think you should never buy a knife for a knife nut. We tend to be extremely picky.... Instead of a knife maybe put together a knife care kit. One of these is essential

http://www.knivesplus.com/KP-STROP8-STROPBLOCK.html

Some corrosion inhibitor for the blade

http://www.bladehq.com/item--Aegis-Solutions-EDCi-Every-Day--27259

And a nice set of torx wrenches

Wiha 36392 L-Wrench Set, Torx, Short Arm, 7 Piece https://www.amazon.com/dp/B002QV0FGA/ref=cm_sw_r_awd_csr5wbA3R9Y2V
https://www.amazon.com/dp/B002QV0FGA/ref=cm_sw_r_awd_csr5wbA3R9Y2V

If you have any money left over, throw in some qtips and microfiber cloths. I know it doesn't seem as cool as a knife, but they would love it

Edit:typos

Best deal for starter sets is these two together from tool discounter, https://www.tooldiscounter.com/ItemDisplay.cfm?lookup=KDT80550P&source=froogle&kw=KDT80550P&gclid=Cj0KCQjw9NbdBRCwARIsAPLsnFYxgfkreQ3glGbzdspWMV5mD8aWE2VIKi9KSriaOK02IKFZc7gz96waAofvEALw_wcB plus the 1/2 kit of you need it/really want it. Add this https://www.sears.com/kd-tools-5-ton-3-2-reversible-puller/p-00999873000P when they go on sale more or take advantage of the spend $75 get $75 back in points. Bondhus Allen wrenches, Bondhus 22199 Hex L-wrench Double Pack, Long Length, 12137 (.050-3/8-Inch) & 12199 (1.5-10mm) https://www.amazon.com/dp/B000E7VG5C/ref=cm_sw_r_cp_apa_kqKTBbVWJSHZT add whatever screwdrivers you fancy and you're probably under the cost of that kit with better stuff

Edit: looked at the link again and missed some stuff, get this extension set at Sears with those bars and get to $75 to get the $75 back https://www.sears.com/craftsman-20-piece-drive-tool-accessory-set/p-A009988410 wrenches if you want standard 12 point ones like are in the kit, wait for the holiday tool displays to get put up and get the 28ish piece husky set at home Depot for like $30 or step up to this gearwrench set https://www.tooldiscounter.com/ItemDisplay.cfm?lookup=KDT81923&source=froogle&kw=KDT81923&gclid=Cj0KCQjw9NbdBRCwARIsAPLsnFbqtP_Ead7DMocuNLPeeDtKV65LkSIchO6oACKELQrmh5-sodXcnlIaAvhEEALw_wcB or like a tekton set like this TEKTON Combination Wrench Set with Store and Go Keeper, Inch/Metric, 1/4-Inch - 1-Inch, 8 mm - 22 mm, 30-Piece | 90191 https://www.amazon.com/dp/B00OXUPFDU/ref=cm_sw_r_cp_apa_gxKTBb29EQ6GK if you prefer 12 points for some reason

My stand: Feedback Sports Sport Stand I love it. Feels really well built and is very easy to collapse and set up.

Tekton are the cheapest I'd go for click torque wrenches. They're a great brand at a very competitive price point. Beam-style torque wrenches can be had for cheaper if you're into that. They're great as well. Reliable, simple, and don't require recalibration. I just prefer the usability of click personally.

Assuming it's the same system as around here, there isn't a lot you can do without proper tools. You'll need a tubular spanner of appropriate length and WD40.

Spanner can either be a more professional one like these: https://www.amazon.com/TEKTON-WRN92002-Telescoping-Capacity-10-Inch/

Or a cheap metal/plastic one if you think it'll move without too much resistance:
https://www.amazon.de/Connex-COX583007-Steckschraubendreher-mit-T-Griff
https://www.amazon.de/Steckschlüssel-Doppelendiger-Wasserhahn-Befestigung-Schraubenzieher


WD 40 helps to address rust. If you want to use heating (dangerous in close confines), make sure you let it cool before screwing and spray with WD 40 after. The heating is to "crack" the rust by widening the parts. If you try to screw while hot, the expansion will work against you.

I was actually looking at these Tekton double box end wrenches I'm not thrilled that they're 6 point but it seems like my best option as of now. If I go that route, I'll definitely get the 8mm, 10mm, 12mm, and 14mm but I'm not sure if I should get anything bigger or even some SAE ones if I'm helping someone else.

Baseball bat, crowbar, breaker bar, torque wrench, shovel, hammer.

There's very few ranged weapons that aren't "considered weapons" but I can put together a very effective pneumatic "gun" that can run off my air compressor or a bike pump.

Triplines, snares, and deadfall traps would also work incredibly well.

A felled tree swinging with a rope that you can pull back to drop again and again would be great, they wouldn't care that they just saw a couple thousand pounds of wood shatter their friends, they'd walk right into it too.

EDIT: Removing stuff on second thought I don't really want tied to my username.

Tekton and harbor freight are your best friend.

Go to harbor freight and get a toolbox, 3 ton jack, and 4 jack stands. A creeper is nice to have.

If you want sockets and ratchet from harbor freight, get the Icon ratchets and Pittsburgh sockets.

I suggest Tekton from Amazon. Start with the 3/8 set, then get the 1/2 and 1/4 set.

https://www.amazon.com/dp/B07P6RJXJ9/ref=cm_sw_r_cp_apa_i_UuaQDbRWPK777

That'll cover your socket needs for the most part.


For wrenches :

https://www.amazon.com/dp/B00OXUPFDU/ref=cm_sw_r_cp_apa_i_CwaQDb63MEAK1

With a toolbox, Jack, Jack stands, socket set, and wrenches, you'll be able to complete most jobs.

Over time, you'll accrue more tools as you need them. I'm a mechanic by trade and, even with a fully matured tool setup, find myself buying tools I need every once and a while.

Join us at /r/tools and www.garagejournal.com

I highly recommend an electronic torque wrench.
The mechanical ones are very inaccurate at the bottom end of range. Head bolts are often at the bottom or below what they can even be set to.

I use this one and it works amazingly well. It can accurately go down to 3ftlb. You can set the desired torque and it has a beep alarm as you approach, reach, and go over the threshold. https://www.amazon.com/gp/product/B004VYUKTC/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1


I also recommend flying with a very basic set of tools. I fly with some hex keys and wrench that fits all the sizes on my paramator. https://www.amazon.com/gp/product/B01F512F74/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1


Siphon is nice to get fuel out of paramotor. This one works amazingly for me. https://www.amazon.com/gp/product/B07CKW15ZS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1


Radio chest harness. https://www.amazon.com/gp/product/B007HJKSG8/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 I added a draw cord to attach my phone to. Phone then tucks into the velcro pocket and is secured by one of these: https://www.amazon.com/gp/product/B01H4E9Z6O/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 It's powerful enough to draw in a medium weight phone.


Hook knife: https://superflyinc.com/products/jack-the-ripper-hook-knife


Power floats: https://glidersports.com/shop/powerfloat-2bsure/

Waste flotation: https://www.amazon.com/gp/product/B013RLI9XS/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1


Cut prop tape strips out of this: https://www.amazon.com/Scotchgard-Clear-Paint-Protection-60-inches/dp/B004VG8DS0/ref=sr_1_9?s=automotive&ie=UTF8&qid=1534535837&sr=1-9&keywords=3m+scotchgard


RTV silicon to put on exhaust springs to reduce vibration fatigue: https://www.amazon.com/Rutland-500%C2%B0RTV-High-Silicone-Black/dp/B000H5Y6CQ/ref=sr_1_5?s=home-garden&ie=UTF8&qid=1534352404&sr=1-5&keywords=heat+resistant+silicon+rtv


Motor tachometer: https://www.amazon.com/gp/product/B01GTP6ORC/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1


Radio: I recommend the FT60 or FT65. The 60 model is tried and true and can also be modded to RX aviation band. FT65 has newer display and is cheaper having been made in China.

Hey! If you have a cassette player, you're gonna need an adapter which can be found here if not you dont need this! Make sure the measurements of the radio match up, it should fit most single/double din radios.


After that make sure to buy a wiring harness


And then get your radio!



Also this would help a bunch, be sure you have a 8mm socket ready.

I love my Gearwrench stuff. I have the ratcheting wrenches and some socket stuff, the 120XP ratchets are amazing. I always grab them before my more expensive tools.

For your budget you can get a lot of wrenches:

https://www.amazon.com/gp/aw/d/B0002NYD1W/ref=mp_s_a_1_4?ie=UTF8&qid=1511099834&sr=8-4&pi=AC_SX236_SY340_QL65&keywords=gear+wrench+ratcheting+wrench+set&dpPl=1&dpID=51Ney6Tn4JL&ref=plSrch

https://www.amazon.com/gp/aw/d/B0002NYD12/ref=mp_s_a_1_5?ie=UTF8&qid=1511100241&sr=8-5&pi=AC_SX236_SY340_QL65&keywords=gear+wrench+ratcheting+wrench+set&dpPl=1&dpID=51MI3AtWo7L&ref=plSrch

https://www.amazon.com/gp/aw/d/B01MZ66M6O/ref=mp_s_a_1_27?ie=UTF8&qid=1511100494&sr=8-27&pi=AC_SX236_SY340_QL65&keywords=gearwrench+stubby

Call Grohe for the spray replacement and ask them for the o-ring for the base. I am sure they will either send it for free or charge something that is much cheaper than new faucet. To remove the faucet you'll need faucet wrench. Make sure you use plumber's putty when installing faucet back so no more leaks will form. Easy fix.

Like others said, lights (rechargeable), creeper, good jack and/or jack stands, magnet bowl, magnet's pen(see link), torque wrench, breaker bar, Car ramps. Or maybe if you have a harbor freight in your area a gift card there. I use to always buy craftsman tools but with them(sears) hurting so bad lately i have started buy HF stuff because they make warranty exchange so damn easy and stuff is cheap in price.

Link 1

Link 2

Link 3

Dont go off the brands i linked just the type of tool itself. Also a vice, or C-clamps, or portable speaker to use while working on said car. :)

I hope this helps you some...

This might be excessive, but I wanted to be thorough so you can see what all is out there. I am having trouble thinking of anything that the following tools can't do, in terms of AR building and maintenance. This is basically my setup at home, though some.of the brands and whatnot are different.

I am operating under the assumption that you already have some basic hand tools in addition to the torque wrench.

The only things you absolutely need are roll pin punches and an armorer's wrench and some basic hand tools like Allen wrenches, screwdrivers, needlenose pliers and so on. The rest just expedite the process and help solve weird issues that may come up.


Wheeler Engineering Roll Pin Starter Punch Set https://www.amazon.com/dp/B01B3NWBVI/ref=cm_sw_r_cp_apa_QJZDAb1ZFBQ80

Wheeler Roll Pin Punch Set https://www.amazon.com/dp/B00EE6GHVW/ref=cm_sw_r_cp_apa_4JZDAbV5YGA8M

Wheeler Hammer and Punch Set In Plastic Case https://www.amazon.com/dp/B004SY07HU/ref=cm_sw_r_cp_apa_FNZDAb1Y74EF0

Geissele Automatics 10-169 AR15/M4 Reaction Rod https://www.amazon.com/dp/B01EY6WFAI/ref=cm_sw_r_cp_apa_hOZDAbD3JHBAE

Aeroshell 33ms / MIL-G-21164D / MIL-SPEC Barrel Nut Thread Grease + 1/2oz can https://www.amazon.com/dp/B01BJ3HE0K/ref=cm_sw_r_cp_apa_4OZDAbQGRYJJ2

TEKTON Long Arm Ball End Hex Key Wrench Set, Inch/Metric, 26-Piece | 25282 https://www.amazon.com/dp/B00I5THF4W/ref=cm_sw_r_cp_apa_PPZDAbQ05H680

TEKTON Long Arm Star Key Wrench Set, T10-T50, 9-Piece | 25291 https://www.amazon.com/dp/B00I5THF9M/ref=cm_sw_r_cp_apa_cQZDAbRX59VNW

IRWIN Tools Multi-Purpose Bench Vise, 5-Inch (4935505) https://www.amazon.com/dp/B009TOCZEC/ref=cm_sw_r_cp_apa_1QZDAbT8R47J0

Yost UP-360 Universal 6 Inch Prism Style Jaw Cover https://www.amazon.com/dp/B01EVQH42U/ref=cm_sw_r_cp_apa_aRZDAbRHAV73E

Real Avid Gun Tool Pro - for Modern Sporting Rifles https://www.amazon.com/dp/B00IMHX5KA/ref=cm_sw_r_cp_apa_bUZDAbEB87JFB

Wheeler Firearms Accurizing Torque Wrench https://www.amazon.com/dp/B0012AXR4S/ref=cm_sw_r_cp_apa_xWZDAb1SRYD6D

Wheeler Professional Gunsmithing Screwdriver Set (43-Piece) https://www.amazon.com/dp/B00HTN4EWG/ref=cm_sw_r_cp_apa_HXZDAbQX5BEWF

TacWater USA AR15/M4/M16 Tools Multi-Purpose Tool Set (W) https://www.amazon.com/dp/B079H5WWZ3/ref=cm_sw_r_cp_apa_GYZDAbRGY3CNH

Takedown Pivot PIN Tool set 223 556 6.8 SPC 300 AAC https://www.amazon.com/dp/B017OUSJFQ/ref=cm_sw_r_cp_apa_V.ZDAbSHZPEG5

Magpul Bev Block https://www.midwayusa.com/product/1015877615/magpul-bev-block-ar-15-action-block

During the winter months I also have a set of extraction mats. If I'm not getting traction, I slide them under the truck tires, and it gives me a little extra grip. I've only had to use them a few times, but they've really helped when I needed them!

But yeah, get the standard stuff, jumper cables, headlamp, etc.

I like a first aid kit and a few extra tools. I tend to have some of the cheap emergency blankets as well.

I also have this little tool in my console:
https://www.amazon.com/gp/product/B071YKX8HN/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1

I have used it a grand total of three times. The first time was to help start a gas-fueled fireplace outside of a brewery when the bartender lost their key for it. The second and third time was to drop retractable/foldable posts designed to keep vehicles out of particular areas. However, I had been asked to drive my vehicle into those areas for work purposes and when other people were done they just locked up and left. The second time it happened it was ten degrees, snowing, and with no cell signal. So yeah, for under ten bucks, it has been handy.

Not a dealership lube tech but I'm a C tech in a independent shop. Get yourself a claw style oil filter socket and a torx bit set up to t-60 if lube techs do diff services in your dealership. Subarus are pretty easy to do maintenance on since you really only need a 8mm, 10mm, 12mm, 13mm, 16mm, and 17mm wrench/socket set to do most things.

I don't have a Rev, but two boards. I'd definitely recommend this hex key set. Not necessarily to carry around, but its good to have a set to keep screws snug.

EKLIND 55166 Cushion Grip Hex T-Key allen wrench - 6pc set Metric MM sizes 2-6 (6In shaft) https://www.amazon.com/dp/B0000CBJDV/ref=cm_sw_r_em_apa_i_-evHDbH2ZGVNK

I replaced:

1. driver and passenger side valve cover gaskets
   
   
2. driver side valve cover (FINDAUTO Valve Cover 13264-EA210... https://www.amazon.com/dp/B07Y1Q3C5Z?ref=ppx_pop_mob_ap_share ) (because I broke my original one trying to replace spark plug hole seals)....I recommend replacing both valve covers because those center seals are probably cooked if you’re anywhere near 100k+ miles—and they’re non-serviceable on the frontier’s cheesy plastic valve covers.
   
   
3. all 1-6 spark plugs (check that your ignition coils are also good while you have them out.)
   
   
4. Air plenum and throttle body gaskets (you can get them both as a kit) Vincos Upper Intake/Plenum Gasket... https://www.amazon.com/dp/B07PKQBLM1?ref=ppx_pop_mob_ap_share
   
   
5. Air filter: Bosch Workshop Air Filter 5486WS... https://www.amazon.com/dp/B00VC1Q0Q4?ref=ppx_pop_mob_ap_share
   
   
6. Engine air cleaner intake duct (mine were cracked): Engine Air Cleaner Intake Duct... https://www.amazon.com/dp/B07K7V2ZX6?ref=ppx_pop_mob_ap_share
   
   
7. Pcv Tube (I might be misnomering this part)— (breather tube between the two valve covers. Mine was completely dry rotted) Part No.: 11826-EA200 nissanpartsdeal.com
   
   
8. Two intake valve timing control gaskets (p/n 23797-ZA000 nissanpartsdeal.com)—mine were cashed and you have to take the air Plenum off to replace the passenger side one, so you might as well do it while your Plenum is off. You have to remove these valve control modules to remove the valve covers anyway, so replacing their gaskets is a no-brainer.
   
   •••••••••
   
   
9. My next project is to replace my oil cooler gasket:
   
   MAHLE Original B32573 Engine Oil... https://www.amazon.com/dp/B0184JRWN6?ref=ppx_pop_mob_ap_share
   
   Mine is pissing oil.
   
   •••••••••
   
   I also replaced my number 3 ignition coil. Mine was bad. A mechanic did that one for me. It’s a pisser. 🤦🏻‍♂️
   
   ••••••••
   
   If you need a good low-force torque wrench, I recommend this: TEKTON TRQ21101 1/4-Inch Drive... https://www.amazon.com/dp/B01M12284X?ref=ppx_pop_mob_ap_share
   
   It’s only 1/4” drive, but it works very well. High quality.

I have an allen wrench set like this that has everything in metric and standard that you would ever need for a guitar setup. The best part is its easy to find when you need it and you dont lose the smaller keys.

these are less than half and use a big shoulder on the ratcheting section which makes them more fun to use, but they aren't quite as sturdy. I have a set of each and I use the cheaper ones more, but they aren't good for breaking tough nuts/bolts loose like the Matco ones are. They are also all spline drive so they are great at gripping stuff that is partially rounded and star heads.

I have thought about putting together an "urban" kit something like this:

A variety of different bump keys

Easy to carry set of lock picks

A multi-functional silcock key to access water

A "truckers friend" combination crowbar, axe, hammer

Sawzall blade handle and various blades for cutting metal and wood

And a good pair of gloves

I think this would cover all my bases and be able to get me into or out of pretty much anywhere I can expect to be, but it's a lot of equipment so I think it may be overkill

**The links are just representative of what I have in mind and not the actual product I would purchase.

i think CDI makes torque wrenches for snap-on...could be wrong about that. i am pleased with this one i bought a couple years ago. also got a smaller 3/8" drive

i hear that any snap-on tool truck will calibrate them for free but its been a while since i did the research.

hope this helps

https://www.amazon.com/gp/product/B002LA1EDO/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

The US General 5 Drawer Tool Cart is a beginner mechanic's best friend.

A word of warning though; don't buy combination wrenches from Harbor Freight. They skip sizes, and that's not what you want when you're working on several types of cars that can't agree on standard sizes.

IMO this is the best set you can get for your money, but you will need to get a 23mm separately if you ever want to change the diff oil in a Miata.

(PROTIP: 15/16 is 24mm and 5/16 is 8mm.)

Hey, girl. I have colitis too (ischemic). I hear you on the bathroom thing. Boy, do I ever.

Might want to get yourself one of these. They're easy to install, all you need is an adjustable wrench and a flat head screwdriver. Even if you're not particularly handy, this is seriously easy. And worth it, holy cow, SO WORTH IT.

The first time you try it will be a shock because the water's not warmed up at all, but you get used to it, and after a flare-up, that cold water is a blessing. Very soothing. Stops me from shaking after I explode and am draped there, wrung out and weak.

Father here, came to say this. Not everybody has mechanical skills, so here's what you need.

1. A Crescent Wrench. Locally, they cost about $3 for a 6 inch Crescent Wrench at Lowes. Online I found this one for about $8.
   
   
2. Use the Crescent Wrench to tighten this bolt
   
   Not only will your kid be safer, the bike will last longer and you will be a better person for having learned this trick.

First, you will need one of these:

Superior Tool 06020 Tub Drain Wrench (Dumbell Wrench)-Dual Ended Drain Wrench that fits 3/8 or 1/2 Inch Ratchet Wrench https://www.amazon.com/dp/B000AO193S/ref=cm_sw_r_cp_api_i_JlDVCb2E0FKA4

Then, if the metal cross bars on the tub shoe snap when you use that tool, you’ll need one of these:

https://m.grainger.com/mobile/product/1VUV1?gclid=CjwKCAjwzPXlBRAjEiwAj_XTEebjhmh8B5mQZwXgYXOLbfjkBm5oCQT9xhza3WVfOgZb5uvi5SPkvRoCvJAQAvD_BwE&cm_mmc=PPC:+Google+PLA&ef_id=CjwKCAjwzPXlBRAjEiwAj_XTEebjhmh8B5mQZwXgYXOLbfjkBm5oCQT9xhza3WVfOgZb5uvi5SPkvRoCvJAQAvD_BwE:G:s&s_kwcid=AL!2966!3!216788409968!!!g!296274828640!

And if that strips out the tub shoe, you’ll need a sawzall and surgical precision.

Wiha 36392 L-Wrench Set, Torx, Short Arm, 7 Piece by Wiha http://www.amazon.com/dp/B002QV0FGA/ref=cm_sw_r_udp_awd_MXEutb02WVQH0

Awesome little set, quality tools that will do many jobs without destroying screws or falling apart.

I like the T-handles made by Bondhus the best. I also have similar ones by Eklind, but I find the handles to be a little flexy for my taste on the smaller sizes. Both are top quality though, Made in USA.

This is what I have in place of sockets to carry. I do have this as well, but you might be looking for more sockets. The pliers wrench should cover most things and it's way better than a nut fucker.

Always great to see the yellow stickers!
Just a heads up too, this was on slickdeals today as Amazon's deal of the day:
https://www.amazon.com/gp/product/B0002NYD1W/ref=ox_sc_act_title_1?smid=ATVPDKIKX0DER&psc=1

Leverage.


I have the matco (3x as expensive) version of all of these:

https://www.amazon.com/GearWrench-81230F-Polish-Handle-Ratchet/dp/B000V5G7LU/ref=pd_sbs_469_2?_encoding=UTF8&pd_rd_i=B000V5G7LU&pd_rd_r=WFB0XHAVEFRVD1DD6CZS&pd_rd_w=itHwF&pd_rd_wg=A03cy&psc=1&refRID=WFB0XHAVEFRVD1DD6CZS


I have this set and the larger set and I use the shit out of them:

https://www.amazon.com/GearWrench-85988-Ratcheting-Wrench-GearBox/dp/B000T8WFBU/ref=sr_1_4?s=hi&ie=UTF8&qid=1509582952&sr=1-4&keywords=long+gear+wrench

https://www.amazon.com/TEKTON-25291-9-pc-Star-T10-T50/dp/B00I5THF9M

$10ish with Amazon Prime and ordered in the next 11 hours it's guaranteed to be there before 8pm Thursday.

but honestly, there's probably a Home Depot or Lowes or w/e within an hours drive of you (provided you live in the States)

I would just buy a complete set of hex/allen keys. They don't cost that much and are useful for other things as well.

http://www.amazon.com/Stanley-85-753-Piece-Long-Metric/dp/B000NIFJQE/ref=sr_1_1?s=power-hand-tools&ie=UTF8&qid=1452031562&sr=1-1&keywords=hex+key+set

The cost of a plumber got me thinking about a specific tool, a basin wrench , that basically makes it a bazillion times easier (and cheaper) to tighten the big awkward nut that attaches the base of your sink doohickies to the underside of your sink/kitchen counter. Probably a lot of tools out there that make diy repairs a lot easier.

All the screws that hold the body itself together are T10 heads. I got this set off Amazon, works like a charm.

• Laptop
  
  
• Logitech MX Rechargeable Bluetooth Mouse
  
• Communication Cables (USB Serial Converter, DB9 Gender Changers, AB Cables, Ethernet of various sizes, RJ45 Coupler, etc.)
  
• Wiha SlimLine Kit
  
• Fluke 789 Processmeter
  
• Test lead Kit
  
• Voltage Sniffer
  
• 5-Port Switch
  
• Wire Stripers
  
• Wiha Dikes
  
• Needle Nose
  
• Fold-up Allen Wrench
  
• Klein Tool Bag
  
• Swiss Army Backback
  
• Electrical Tape, Fuses for Field Install and Multimeter Spares, Surge Protector, USB Drives with Automation Software, Fold-up TV Dinner Table, Fold-up Chair with Cushion, Notebook, Business Cards, Pens, Sharpies, Phone, Hardhat w/ Headlamp, Safety Glasses, Electrically Insulated Steel Toed Boots.
  
  
  
  This is setup is mainly for project startups and it would probably change if I was in more of a service engineer role.

I think this craftsman one is a little more well made. I picked it up after stripping my plastic filter socket. It's like $12.99 if you get it from Sears

https://www.amazon.com/Craftsman-Oil-Filter-Wrench-Auto-Adjustable/dp/B003Y22RDO

FML

A. As a nightshifter: Royally fuck you winterhour, let the time of depression and moodswing begin!

B. Just spent 1.5 fucking hours trying to look for 1. a tool (or) 2. the name of the fucking tool in Dutch

It's fucking sick, I need this thing to unclog my fucking bath, 10$ on amazon in the US, OR a fucking 80 euros on amazon.de (?!!) OR it's a reasonable price but they're unable to deliver

So then, maybe fucking bol.com or gamma or something... half an hour of searching for the translation of 'dumbell wrench', conclusion: It just doesn't have a fucking name, I tried everything.

I'm done with this for today, I guess I'll just cry in the shower whenever I use it and it starts overflowing and reminding me of my incompetence /s

Could also pay someone to do it, but who's got the fucking money for that?

If any of you have a golden tip.... I'd be grateful

(it's to remove the drain-cover-shitthing from my bath, which has been clogged off and on up for 5 years or so)

Edit: Thanks for the helpful advice <3 Appreciate it!

10 and 14mm? I've NEVER seen hex bolts that big on a bike - they would correspond to M12 and M16 SHCS - so, half an inch diameter screws. you may be thinking of cone wrenches, which would vary based on hub manufacturer (and on older bikes, headsets).

For hex wrenches/allen keys, you don't need the fancy T handled wrenches. They're nice, but they're a luxury. If you're going cheap, just get a normal set of metric hex wrenches (like this - bonus SAE wrenches to boot http://www.amazon.com/Stanley-85-753-Piece-Long-Metric/dp/B000NIFJQE/ref=sr_1_1?ie=UTF8&qid=1405808907&sr=8-1&keywords=metric+hex+key+set ) or a folding set if you want something to take with you (but don't expect to be able to get crankarms off with it!) http://www.amazon.com/Bike-Tool-AWS-11-Metric-Folding/dp/B000OZFI76/ref=sr_1_5?ie=UTF8&qid=1405808982&sr=8-5&keywords=park+tool+folding

If you have a fancier bike with carbon components, or want to get serious about bike maintenance, do yourself and your bike a favor and buy a torque wrench and a set of hex bits. The smaller bolts with lower torques (2-5 Nm range) tend to be the ones you'll overtorque and damage parts, so start with a torque wrench with a low range first. You can add the larger torque wrench (~10-75 Nm range) later.

Other than that, just get the tools for the jobs you end up doing on your bike. A chain breaker is a must, and cone wrenches for your hub (if it uses them) are great to have.

http://www.amazon.com/Superior-6020-Wrench-2-Inch-Ratchet/dp/B000AO193S

This is the tool that i used to remove my drain. Hope this helps. When you reinstall it, just remember to use plumbers putty.

My friend that works at a (really good) local shop has used this style for years. I have used it when I did an oil change or three for him when when I was bored and hanging out at his shop

http://www.amazon.com/Craftsman-Oil-Filter-Wrench-Auto-Adjustable/dp/B003Y22RDO/ref=sr_1_1?ie=UTF8&qid=1396473414&sr=8-1&keywords=B003Y22RDO

It works VERY well on a range of filter sizes.
Edit - dangit now that I look at that link carefully, it is that style but probably a different brand

I've been happy with my Tekton metric set. The prices have gone up though, I got my metric set for about $35 in early 2017, but now they're about $50 each or $100 for both the SAE/Metric set.

Here's the SAE/Metric sets: https://www.amazon.com/TEKTON-Combination-Wrench-Keeper-Metric/dp/B00OXUPFDU/ref=sr_1_3?keywords=tekton+wrench+set&qid=1557847901&s=gateway&sr=8-3

A dumbell wrench may help too if the threads are frozen. link

I got this set. Expensive but they're working well so far.


https://www.amazon.com/Wiha-36392-L-Wrench-Short-Piece/dp/B002QV0FGA

Might be worth investing in a good set of t-handle allens wrenches for the future, to avoid stripping axels.

This is the set that I use.

Thank you, I just placed an order for this one: https://www.amazon.com/TEKTON-Wrench-T10-T50-9-Piece-25291/dp/B00I5THF9M/ref=sr_1_4?s=hi&ie=UTF8&qid=1499874013&sr=1-4&keywords=torx

Why do you recommend the socket type over the open jaw/telescoping type?

https://www.amazon.com/Superior-Tool-Eleven-Wrench-Infinitely-Adjustable/dp/B0000CBJD4

I agree, build you own kit. Below is my take. Know that some of those tools are not for every day use in networking, but who can resist getting more tools? Also, if you get all of these I realize it will be over $200. So, just use this list as a guide not a definitive list.

BAGS

• 5.11 Rush 24 Pack (Should fit all tools): http://www.amazon.com/gp/product/B002N1G2WY
  
  
• 5.11 Tactical Small Kit tool Bag (for the essentials):
  
  • http://www.511tactical.com/small-kit-tool-bag.html
    
  • http://www.amazon.com/gp/product/B001A66GDI
    
    
• 5.11 Tactical Shell pouch # x2 in 2 different colors:
  
  • http://www.511tactical.com/shotgun-ammo-pouch-vtac.html
    
  • http://www.amazon.com/gp/product/B009PTSUUO
    
  • one pouch for rj45 connectors
    
  • one pouch for cage nuts
    
    ETHERNET TOOLS
    
    
• Punch down tool: http://www.amazon.com/gp/product/B0000AZK4D
  
• Crimper: http://www.amazon.com/gp/product/B002D3B97U
  
• Network Cable Tester: http://www.amazon.com/gp/product/B00DQH4XPW
  
• Cage Nut Tool: http://www.amazon.com/gp/product/B00DL09HPU
  
• Wire Stripper: http://www.amazon.com/gp/product/B00CJWUEMQ
  
• Ethernet cable stripping tool: http://www.amazon.com/gp/product/B00788LVZA
  
• Coax and Data Cable Cutter: http://www.amazon.com/gp/product/B003S5VE0Y
  
  SCREWDRIVERS
  
  
• Steelex D2023 Magnetic Tip Screwdriver Bit Set 30-piece: http://www.amazon.com/gp/product/B0000DD6T9
  
• Klein 32561 Std. Stubby Screwdriver: http://www.amazon.com/gp/product/B005FQDHHC
  
• 15 in 1 Screwdriver: http://www.amazon.com/gp/product/B004VJY99Y
  
• Philips Head Screw Driver with magnetic tip #3: http://www.amazon.com/gp/product/B007ISYR6K
  
• iFixit Precision Screw driver 54bit set: http://www.ifixit.com/Store/Tools/54-Bit-Driver-Kit/IF145-022
  
  PLIERS and WRENCHES
  
  
• Needle Nose Pliers: http://www.amazon.com/gp/product/B000JNNW1M
  
• RoboGrip 7" Wrench Pliers: http://www.amazon.com/gp/product/B000PEPAFQ
  
• Tekton 26-pc Long Arm Ball Hex Key Wrench Set (inch/metric): http://www.amazon.com/gp/product/B00I5THF4W
  
• Tekton Star Key Set: http://www.amazon.com/gp/product/B00I5THF9M
  
• Craftsman Evolv 3 pc. Adjustable Wrench Set: http://www.amazon.com/gp/product/B0056BJFOK
  
• Tekton Combination Wrench Set (Inch/metric): http://www.amazon.com/gp/product/B000NQ159G
  
  POWER
  
  
• 1.8" LCD 20+4-pin Power Supply Tester w/8/6/4-pin Connectors: http://www.amazon.com/gp/product/B001MKCALY
  
  MISC
  
  
• CRKT 3 inch folding Knife: http://www.amazon.com/gp/product/B0017UV9W0
  
  
  SUPPLIES
  
  
• Pack of 100 RJ45 connectors: http://www.amazon.com/gp/product/B00BS92DCK
  
• 75ft Role of velcro: http://www.amazon.com/gp/product/B0069FJR2M
  
• Electric Tape: http://www.amazon.com/gp/product/B00004WCCL
  

I've got this multi-tip version of a panel key, which looks like it includes your size of triangle key. It's wicked useful and you can't beat the price.

A few tips I didn't see already listed:

• Plumber's putty: use it when you install the faucet, like you're supposed to. I didn't when I replaced my kitchen faucet, and I really need to take it apart and do it right.
  
• Basin wrench, like this - I didn't know what one was until I saw them mention it on Ask This Old House, and it made installing our new bathroom vanity a breeze.

If you want something that's actually accurate and not a piece of shit get a CDI Torque Wrench. CDI is Snap On's industrial brand. It's basically the exact same thing that would come off the tool truck but at 1/2 the cost of a Snap On branded one. I have 3 of these and would still buy them all day long. https://www.amazon.com/CDI-2503MFRMH-Micrometer-Adjustable-Torque/dp/B002LA1EDO/ref=sr_1_1?ie=UTF8&qid=1506280402&sr=8-1&keywords=cdi+torque+wrench+1%2F2+inch

I second Wiha. I haven't had any trouble with mine: http://www.amazon.com/Wiha-36392-L-Wrench-Short-Piece/dp/B002QV0FGA/ref=sr_1_6?ie=UTF8&qid=1426552423&sr=8-6&keywords=wiha+torx

The PH-1 set isn't bad, but for my money I'll go with the $13 Stanley Long-Arm set any day.

Buildtak spatula: https://www.amazon.com/gp/aw/d/B017XGEDOM/ref=mp_s_a_1_1?ie=UTF8&qid=1521340627&sr=8-1&pi=AC_SX236_SY340_QL65&keywords=buildtak+spatula

Needle nose pliers: you don’t really need quality here, I just use a set from a multitool

Sandpaper: just go to a Home Depot or similar

Hex set: https://www.amazon.com/gp/aw/d/B00D4C18CU/ref=mp_s_a_1_6?ie=UTF8&qid=1521340573&sr=8-6&pi=AC_SX236_SY340_QL65&keywords=hex+keys

Tekton wrenches: https://www.amazon.com/dp/B00OXUPFDU

GearWrench sockets and ratchets: http://www.tooldiscounter.com/ItemDisplay.cfm?lookup=KDT80300P

Kobalt cabinet I found on clearance for $160: https://m.lowes.com/pd/Kobalt-3000-35-in-W-x-47-in-H-7-Drawer-Steel-Rolling-Tool-Cabinet-Black/1000437815

Anyone have recommendations for mounting the wrench holders to the pegboard on the inside of the lid?

Local hardware store have Hex key setHex key set for cheap. Most atomizers uses the 2nd smallest one.

Maybe if you really needed to, but seriously, just buy a set of allen keys. I got mine for 11.50$ on amazon and they have been as reliable as I could ask for. In fact, here.

Allen keyed then.

https://www.amazon.com/Stanley-STHT71839-Folding-Metric-2-Pack/dp/B00D4C18CU/ref=sr_1_5?s=hi&ie=UTF8&qid=1505792228&sr=1-5&keywords=allen+key+set

I think the PI wrench or the CDI wrench is about 150 (1/2 inch drive).

http://www.amazon.com/CDI-Torque-2503MFRMH-Micrometer-Adjustable/dp/B002LA1EDO/ref=sr_1_1?ie=UTF8&qid=1450228327&sr=8-1&keywords=CDI+1%2F2+torque

Here are some links for the product in the above comment for different countries:

Link: link


|Country|Link|
|:-----------|:------------|
|Canada|amazon.ca|




This bot is currently in testing so let me know what you think by voting (or commenting).

Gearwrenches: http://www.amazon.com/GearWrench-9416-Metric-Master-Ratcheting/dp/B0002NYD1W/ref=sr_1_3?ie=UTF8&qid=1419886288&sr=8-3&keywords=gear+wrench

Star shape is torx wrench. should be able to buy from a local hardware store or amazon

TEKTON TRQ21101 1/4-Inch Drive Dual-Direction Click Torque Wrench (10-150 in.-lb./1.1-16.9 Nm) https://www.amazon.ca/dp/B01M12284X/ref=cm_sw_r_cp_api_i_z5z4CbE8P5N9B

$65CAD

It is a basin wrench

7 for two sets, one 'murikan, and one metric

https://www.amazon.com/Stanley-85-753-Piece-Long-Metric/dp/B000NIFJQE/ref=sr_1_3?ie=UTF8&qid=1499360414&sr=8-3&keywords=allen+key+set

OP, you ought to get a tub drain wrench, use it to remove the drain, then use the shop vac on it.

For what it's worth, there actually aren't that many different sizes. Every key you own is probably identical to one of these... https://www.amazon.com/Stanley-STHT71839-Folding-Metric-2-Pack/dp/B00D4C18CU/ref=sr_1_2?ie=UTF8&qid=1541438452&sr=8-2&keywords=stanley+allen+wrench

So if your stash ever overwhelms you, don't ever feel like you absolutely must keep them all.

The kit lacks a hex wrench set, which is a central fixture in any bicycle toolkit. Whether or not you buy that set, you won't get far without metric hex wrenches. The fact that they omitted such an important piece makes me really skeptical about the rest of it.

I have an SAE/Metric set of Stanley hex wrenches, similar to this $10 set. They've been serving me well for years (except the 4mm wrench that I lost X_X).

Since you're lacking a tool bag, these would be useful for you.

http://www.amazon.com/dp/B00D4C18CU

You'll get the bolts loose to raise the tank.

Tank prop, I can't seem to find one, since mine didn't come with one either. I just use a dead blow hammer and prop it up.

I set up a tool box for my younger brother this year and this is the socket set I picked for him
GearWrench 80550 57 Piece 3/8-Inch Drive 6 Point Socket Set https://www.amazon.com/dp/B000NICEVW/ref=cm_sw_r_cp_api_2D.wybBAS3832

I also got the
GearWrench 81210P 120XP Cushion Grip Flex Teardrop Ratchet, 3/8-Inch https://www.amazon.com/dp/B00BTEXV52/ref=cm_sw_r_cp_api_sF.wyb6FDSS1G

Wrench set
TEKTON 90191 Combination Wrench Set with Store and Go Keeper, Inch/Metric, 1/4-Inch - 1-Inch, 8 mm - 22 mm, 30-Piece https://www.amazon.com/dp/B00OXUPFDU/ref=cm_sw_r_cp_api_mG.wybM57PJSQ

Basic stuff
Ball pein hammer
Dead blow hammer
Feeler gauge
Brass drift pin
Sparkplug sockets
Assortment of pliers
Assortment of screwdrivers
Crescent wrenches

https://www.amazon.com/dp/B000V5G7LU/

My bad. Shoulda realized you were missing the ratchet too! 😜

I spent 9 years working in IT, and my guess is that it's going to be a T10 torx bit. If your buying a set, get a decent one. My experience is with HP proliant servers, and they have always used a ton of locktite on those screws to keep them from giggling lose from vibration while running. I have personally broke a few of the cheaper drivers trying to get those screws out. Make sure you use the right size driver, the tricky thing about torx is that a smaller size can trick you into thinking that it will work, but those screws will be tight enough from the factory that the wrong size will strip the screw out. The correct won't have any slop and won't be able to wiggle inside the screw.

I would get torx keys if you can like these:
If you're ok with made in China, I'd recommend Tekton
http://amzn.com/B00I5THF9M
Otherwise klein makes killer Made in the USA tools
http://amzn.com/B0018BS7GY