Reddit mentions: The best motor oils
We found 308 Reddit comments discussing the best motor oils. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 138 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Shell Rotella T6 Full Synthetic 5W-40 Diesel Engine Oil (1-Gallon, Single Pack, Old Packaging)
- Better fuel economy - compared to 15W-40 oils Rotella offers enhanced fuel economy capability of 1.5% without compromising engine protection or durability
- Improved wear performance - provides a significantly increased level of protection against harmful engine wear when compared to previous generation API CJ-4 engine oils
- Improved deposit control - advanced multi-functional dispersant additives in combination with synthetic base oils provide an enhanced level of protection against the effects of soot, dirt and other contaminants
- Emissions system compatibility - advanced low-ash formulation helps control blocking of or poisoning of exhaust after-treatment devices, helping maintain vehicle emission compliance and engine fuel efficiency
- Improved heat resistance - resists breakdown by heat to provide continuous protection throughout the service interval
- Shell Rotella T6 full synthetic oil features an advanced multi-functional, low-ash additive technology in a synthetic base oil designed to provide highly responsive protection that continuously adapts to your driving conditions
- Rotella T6 is formulated with reduced levels of ash, phosphorous and sulfur to help maintain the efficiency of the latest vehicle-emissions technologies
- Shell Rotella T6 5W-40 provides excellent low-temperature flow, even at -30 degrees Fahrenheit
- Shell Rotella T6 5W-40 provides unsurpassed protection against shear-stability degradation, compared to the leading competitive API CJ-4 5W-40 products
Features:
Specs:
Height | 12.87 Inches |
Length | 9.61 Inches |
Number of items | 1 |
Release date | May 2013 |
Size | 1 Gallon |
Weight | 0.25 Pounds |
Width | 12.76 Inches |
2. DuPont Motorcycle Degreaser for Chain and Sprockets Aerosol, 11 oz
Strong & fast acting, yet safe for all sealed / O-ring chainsmade with biodegradable ingredients including soy extracted estersNo water rinsing required, just spray, wipe, re-lubricate and rideSafe for all x-ring, z-ring, O-ring chainsQuickly cleans grease, dirt, wax & grime off chains & sprockets
Specs:
Height | 8 Inches |
Length | 2.75 Inches |
Size | 11oz Aerosol |
Weight | 0.6875 Pounds |
Width | 2.75 Inches |
3. Mobil 1 94001 5W-30 Synthetic Motor Oil - 1 Quart (Pack of 6)
- Mobil 1 advanced full synthetic motor oil 5W-30 helps to protect your engine from the five factors that can damage engines over time
- Helps to protect critical engine parts for up to 10,000 miles between oil changes*, controlling oxidation to prevent oil breakdown and maintaining excellent viscosity
- Meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean and helping to improve your fuel economy
- Helps extend engine life by working to prevent damaging deposits and sludge buildup
- Provides excellent internal engine heat protection (up to 500 degrees F) and low temperature protection (to -30 degrees F)
Features:
Specs:
Height | 9.5 Inches |
Length | 9.13 Inches |
Number of items | 6 |
Release date | May 2019 |
Size | 1 Quart (32 Ounce), (Pack of 6) |
Weight | 12 Pounds |
Width | 7.63 Inches |
4. Mobil 1 120760 Synthetic Motor Oil 0W-40, 5 Quart
- Mobil 1 Fs European Car Formula Full Synthetic Motor Oil 0W-40 Helps To Extend Engine Life Even In Severe Conditions
- Helps To Control Oxidation To Prevent Oil Breakdown And Maintain Excellent Viscosity For Up To 10,000 Miles Between Oil Changes
- Provides Outstanding Engine Wear Protection And Performance With Uniform Synthetic Oil Molecules For Better Friction Reduction
- Keeps Your Engine Running Like New By Working To Prevent Damaging Deposits And Sludge Buildup
Features:
Specs:
Height | 12.66 Inches |
Length | 4.4 Inches |
Number of items | 1 |
Release date | March 2014 |
Size | 5 Quart |
Weight | 9.038952742 Pounds |
Width | 8.1 Inches |
5. Shell Rotella T6 Full Synthetic 5W-40 Diesel Engine Oil (1-Gallon, Single Pack, New Packaging)
- Full synthetic 5W-40 diesel engine oil with Triple Protection Plus technology protects against wear, deposits, oil breakdown, and improves low-temperature flow
- Exceptional wear protection for longer life in a wide range of heavy-duty engine applications — from pickup trucks to tractors to semi rigs
- Enhanced fuel economy capability of 1.5 percent without compromising engine protection or durability (compared to 15W-40 oils)
- Multi-functional dispersant additives provide an enhanced level of protection against the effects of soot, dirt, and other contaminants (compared to previous formulation)
- Increased shear stability for better viscosity control and optimal engine oil pressure
- Better cold-cranking properties and low-temperature pumpability for reaching critical engine parts faster
- Single 1-gallon bottle with ergonomic design for easy handling and pouring
- Advanced low ash formulation helps protect the exhaust catalysts and particulate filters found on the latest low-emission vehicles
Features:
Specs:
Height | 4.31 Inches |
Length | 11.31 Inches |
Number of items | 1 |
Release date | September 2016 |
Size | 1 Gallon |
Width | 8.1 Inches |
6. Castrol 03124 EDGE 0W-20 Advanced Full Synthetic Motor Oil, 5 Quart
For best performance, follow the manufacturer's recommendations in your vehicle owner’s manual.42 percent better rating on fighting power robbing depositsSuperior engine protection vs conventional and synthetic blend oilsSuperior performance against deposits, wear and oxidation; Bottle Color: Blac...
Specs:
Height | 4.4 Inches |
Length | 11.9 Inches |
Number of items | 1 |
Release date | April 2014 |
Size | 5 Quart |
Width | 9.5 Inches |
7. Liqui Moly 2332 Leichtlauf High Tech 5W-40 Engine Oil - 5 Liter
For best performance, follow the manufacturer's recommendations in your vehicle owner’s manual.Rapid oil delivery at low temperatures, high lubrication reliability at high and low temperaturesLong engine service life due to high level of protection against wear, mixable and compatible with commerc...
Specs:
Height | 3.50393 Inches |
Length | 12.9921 Inches |
Release date | August 2014 |
Size | 5 Liter |
Weight | 9.90096018642 Pounds |
Width | 9.99998 Inches |
8. Liqui Moly 2041 Premium 5W-40 Synthetic Motor Oil - 5 Liter Jug
- The Lubro-Moly Synthoil High Tech 5W-40 Motor Oil is a fully synthetic and energy conserving motor oil for the latest engine concepts (both gas and diesel), such as multi-valve arrangements, variable cam and timing configurations, turbocharging, supercharging, intercooling, etc.
- The Lubro-Moly Synthoil High Tech 5W-40 Motor Oil saves fuel and provides instant lubrication after a cold start.
- Good for extended oil change intervals and the highest demands
- Package Dimensions: 10.312 L x 31.496 H x 24.892 W (centimeters)
Features:
Specs:
Height | 0 Inches |
Length | 0 Inches |
Number of items | 1 |
Release date | May 2013 |
Size | 5 Liters |
Weight | 10 Pounds |
Width | 0 Inches |
9. 3-IN-ONE Motor Oil, 3 oz.
Motor oil lubricates the moving parts in small electric motors to extend the motor's life by reducing wear and tearHigh-grade oil blend provides an SAE 20 oil rating equivalentIncreased viscosity compared to standard motor oils provides extended wear protectionRecommended for use with 1/4 HP or larg...
Specs:
Size | 3 ounces |
10. Motul 8100 X-Clean EFE 5W-30 Synthetic oil, 5-Liter, 1 Pack
- Meets demanding oil requirements set by OEM manufacturers
- Synthetic oil with wear protection and high temp resistance
- Recommendations from Honda, Kia, Toyota, Hyundai, Subaru, and Nissan
- Approvals: BMW LL-04, GM dexos2, MB-Approval 229. 52, VW 505 01
- Extra Fuel Economy (EFE) lubricant, perfect balance of efficiency and protection
- Fit type: Universal Fit
- Flash point: 232.0 degrees_celsius
Features:
Specs:
Height | 7.28 Inches |
Length | 5.31 Inches |
Number of items | 1 |
Release date | September 2018 |
Size | 5 l, 1 Pack |
Weight | 9.87 Pounds |
Width | 11.22 Inches |
12. Mobil 1 120764 Synthetic Motor Oil 5W-30, 5 Quart
- Mobil 1 advanced full-synthetic motor oil 5W-30 utilizes Mobil 1’s signature Triple Action Formula to deliver outstanding engine performance, protection, and cleanliness.
- Helps protect critical engine parts for up to 10,000 miles between oil changes,* controlling oxidation to prevent oil breakdown and maintaining excellent viscosity
- Meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean and helping to improve your fuel economy
- Helps extend engine life by working to prevent damaging deposits and sludge buildup
- Provides excellent internal engine heat protection (up to 500 degrees F) and low temperature protection (to -30 degrees F)
Features:
Specs:
Height | 12.66 Inches |
Length | 4.4 Inches |
Number of items | 1 |
Release date | March 2014 |
Size | 5 Quart |
Width | 8.1 Inches |
13. Valvoline 4-Stroke Motorcycle SAE 10W-40 Motor Oil 1 QT, Case of 6
Special cleaning agents and dispersants help prevent deposit formation and keep engines cleanShear stable viscosity improvers help resist oil film breakdownSilicone additives to prevent foaming and help maintain proper lubricating filmSpecial additives help protect the engine from combustion by-prod...
Specs:
Color | 10W-40 |
Height | 9.25 Inches |
Length | 13.13 Inches |
Number of items | 1 |
Release date | June 2013 |
Size | 1 QT, Case of 6 |
Width | 5.75 Inches |
14. Mobil 1 120758 Advanced Full Synthetic Motor Oil for 0W-20 5, 4.73L
- Mobil 1 Advanced Fuel Economy full-synthetic motor oil 0W-20 is low-viscosity to help improve fuel economy.*
- Utilizes Mobil 1’s signature Triple Action Formula to deliver outstanding engine performance, protection, and cleanliness
- Helps protect critical engine parts for up to 10,000 miles between oil changesm,** controlling oxidation to prevent oil breakdown and maintaining excellent viscosity
- Meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean
- Helps extend engine life by working to prevent damaging deposits and sludge buildup
- Provides excellent internal engine heat protection (up to 500 degrees F) and low temperature protection (to -40 degrees F)
Features:
Specs:
Height | 12.66 Inches |
Length | 4.4 Inches |
Number of items | 1 |
Release date | March 2014 |
Size | 5 Quart |
Width | 8.1 Inches |
15. Castrol 06112 POWER 1 4T 10W-40 Synthetic Motorcycle Oil, 1 Quart Bottle, 6 Pack
For best performance, follow the manufacturer's recommendations in your vehicle owner’s manual.Formulated with Trizone technology to protect all 3 critical zones: engine, clutch and gearboxRace derived technology for maximum engine accelerationExtreme high temperature air-cooled performance and wa...
Specs:
Number of items | 1 |
Release date | July 2012 |
Size | 1 Quart (32 Ounce), (Pack of 6) |
Weight | 2 pounds |
16. Castrol 03101 EDGE 0W-40 A3/B4 Advanced Full Synthetic Motor Oil, 5 quart, 1 pack
For best performance, follow the manufacturer's recommendations in your vehicle owner’s manual.42 percent better rating on fighting power robbing depositsSuperior engine protection vs conventional and synthetic blend oilsSuperior performance against deposits, wear and oxidation; Bottle Color: Blac...
Specs:
Height | 11.81102361 Inches |
Length | 3.93700787 Inches |
Number of items | 1 |
Release date | April 2014 |
Size | 5 Quart |
Weight | 8.99 Pounds |
Width | 9.448818888 Inches |
17. Rotella 550019913 T Triple Protection CJ-4 15W-40 Motor Oil - 1 Gallon
- Shell Rotella T Triple Protection oils provide triple action to help control wear, deposits and emissions to continuously adapt to the needs of the engine for protection in on and off highway applications
- Up to 38 percent lower wear in over 40 million miles of on and off road testing in late-model engines
- Meets or exceeds API CJ-4 requirements, and is designed to provide extra performance; Shell Rotella T Triple Protection performs well in both older and new engines
- 30 percent increase in active ashless chemistry to protect against deposits and sludge
- Using modern multi-component chemistry, Shell Rotella T Triple Protection gives all-around protection for turbo- and non-turbocharged engines alike
- Shell Rotella T Triple Protection Heavy Duty oils provide triple action to help control wear, deposits and emissions to continuously adapt to the needs of your engine for protection in on and off highway applications
Features:
Specs:
Height | 12.5 Inches |
Length | 12.8 Inches |
Number of items | 1 |
Release date | March 2014 |
Size | 1 Gallon |
Weight | 7.74 Pounds |
Width | 9.5 Inches |
18. Liqui Moly 2331 Leichtlauf High Tech 5W-40 Engine Oil - 1 Liter
- Rapid oil delivery at low temperatures, high lubrication reliability at high and low temperatures
- Long engine service life due to high level of protection against wear, mixable and compatible with commercially-available engine oils
- Outstanding engine cleanliness, tested with catalytic converters and performance proved with turbochargers
- Saves fuel and reduces pollutant emission; Optimum oil pressure at all engine speeds, high shear and ageing stability
- Approvals from vehicle manufacturers for Leichtlauf High Tech 5W-40 include BMW Longlife-01, MB-Approval 229.5, Porsche A40, Renault RN 0700, 0710, VW 502 00/505 00
Features:
Specs:
Height | 2.5 Inches |
Length | 7.5 Inches |
Release date | August 2014 |
Size | 1 Liter |
Weight | 1 Pounds |
Width | 6 Inches |
19. Liqui Moly 2005 Diesel Purge - 500 ml
- Fit type: Universal Fit
- Flash point: 63.0 degrees_celsius
Features:
Specs:
Height | 0.43307 Inches |
Length | 1.41732 Inches |
Number of items | 1 |
Release date | May 2013 |
Size | 500 Milliliter |
Weight | 1.09790206476 Pounds |
Width | 0.43307 Inches |
20. Lucas Oil 10710 10W-40 Semi-Synthetic Motorcycle Oil - 1 Quart Bottle
- Package Dimensions: 4.5 L x 9.5 H x 2 W (inches)
- Package Weight : 13 pounds
- Country of Origin : United States
- Part number: 10710
Features:
Specs:
Color | Multi |
Height | 3.7007873978 Inches |
Length | 1.3385826758 Inches |
Number of items | 1 |
Release date | June 2014 |
Size | 1 Quart (32 Ounces) |
Weight | 2 Pounds |
Width | 2.0078740137 Inches |
🎓 Reddit experts on motor oils
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where motor oils are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
The Internet is your friend! I can't imagine the magnitudes of higher difficulty generations before us faced. These days, you can Google "oil change DIY <insert year/make/model of your car>" and you will get endless write-ups from forums that specialize in your car, YouTube videos, dedicated personal sites, etc. I definitely know it seems complex, but if you are even the slightest bit technical-minded and can visualize things, you'll very quickly realize that you can probably take apart almost anything you see under the hood and be able to put it back together. Just be careful, take pictures of things before you disassemble, and buy plenty of magnetic trays ($2-3 from Harbor Freight) to keep track of nuts and bolts. Fortunately, there are plenty of maintenance things you can start with that you can't really break, like changing your engine air filter.
Doing an oil change is probably the next simplest thing you can do. In short, safety first, learn how to jack up your car and put it on jack stands, or just buy Rhino Ramps for $40, undo the drain plug, drain the oil into a big pan, put the bolt back in with a new crush washer, find and remove the filter, sometimes it's one metal thing and other times it's a plastic thing with a filter inside of it, then put the new one back on, then pour in x quarts or liters of oil back up top. Your first few times will take an hour or two and will likely be messy, but you'll very quickly be able to shorten that amount of time and eventually be able to do it without spilling a single drop.
A starter set of mechanic tools will cost you $20-40 on Amazon. Oil and filter is usually $20-40 even if you use the good stuff. But then those tools and ramps will also be used basically forever, so they're one-time costs. Once you do this a couple times and get comfortable getting under the car, looking at things, then you can read about doing transmission or differential fluid changes, start removing some of your engine covers just to take a look around and compare it to all the DIY videos and articles/posts that you can find. Once you have a small set of tools, any subsequent jobs will likely just require maybe 1 or 2 additional specialized tools to access some weird things. Even today, after having done most of my own maintenance for years, I would sometimes have to go on Amazon and spend $7 just to buy some weird size socket just to get to this one thing on specific car. You'll familiarize yourself with bolt clamps, start to see how manufacturers like to connect things, where things get dirtier than other places, look at things that you don't normally see when the car is all buttoned up, all with very little risk. It's also definitely easier on a Japanese car. I learned to work on older German cars when I started, where it took 3-4 different bolts and bits and strange wrangling of plastic trim and linings just to remove a bumper, so then I was pleasantly surprised that all I needed was ONE SINGLE 10mm socket on a dozen exposed bolts to take off my Mazda bumper.
It took me a couple years of light wrenching before I was comfortable enough to do my own brakes (mentally, it always seemed like the biggest risk if I messed something up). Now, I can swap all of my brake pads before a track day in about half hour. I recently bought another VW and learned that it has a common coolant system issue, something I had never worked on before... I spent a couple days reading and watching videos, then just ordered the right parts and went in and did everything while following along and pausing the videos. Took me a couple hours, but now I am not nervous about doing anything coolant-related since I gained a deep understanding how the piping works, etc. In fact, I've now added a simple coolant system flush to my to-do list for my other cars.
I looked at your post history and did some light Googling... looks like this site has your full 553-page manual. Here is the link to page 448 that guides you through an oil change, but it looks like all the maintenance stuff starts on page 432. Based on Amazon's built-in car search tool, it looks like the Fram XG7317 is what fits on a '16 TLX V6 AWD. And the service manual says you should be using 0W-20, which is also something you can find on Amazon... I use Castrol Syntec 0W-20 for my track car that definitely sees a ton of hard driving, and it's usually $25 for a 5-qt jug. Based on this resource, looks like you only need about 4.5 qts. This video seems to be pretty informative to walk you through an entire oil change on the V6.
You probably want to create an account on tlxforums.com and start poking around the maintenance subs. Maintenance section and common issues section.
I would tell you to look for a formal service manual, but I may be dating myself here. It doesn't look like there are paper manuals available to buy (at least from Honda; there may eventually be third party ones). In the meantime, it looks like you can pay to access this one... $30/year? Maybe do some of the more simple DIYs, get yourself familiar, start building up a small tool collection, and then go in there and poke around and maybe even download/print some of the stuff you'd want to do.
Feel free to PM me if you want to discuss more or bounce some ideas around, or if you just need a cheerleader before you dive into your first job. Hell, in typing all of this, I'm feeling pretty good about getting down on some Acura V6 maintenance myself, lol.
&#x200B;
*edit* I didn't realize how carried away I got with this response. I'm sorry for thread-jacking with a text wall, u/op. Let me know if you'd like me to remove this post and share it in a PM instead.
I'm not a professional mechanic, but I have an '83 240D, and here's a few of my tips:
Have you done a valve adjustment? This can make a huge difference on running smoothness. It's not too hard of a job, but I would recommend having a second set of hands. It's nice to have someone with the feeler gauges at the ready to measure while you still have the wrenches on the adjustment screws. You're going to want the special wrenches like these. Usually you can get them on ebay cheaper.
I like using the Diesel Purge product. Pretty simple to do, and only takes a half hour or so. There are quite a few YouTube videos out there about how to do it on a w123 chassis. Change both fuel filters after the diesel purge.
Differential fluid is easy to do, but being you're in the salt might make cracking those plugs difficult.
Cold starts with diesel are always fun, but just a simple thing is when were the glow plugs last replaced? If you're doing the valve adjustment, you're already in teh general area and might as well change them out if it hasn't been done in some time. (Some people say they get 200k+ out of them.) Be sure to get the glow plug reamer as well to clear it out and get that carbon out of the threads.
Here is the filter you need (just search for the model number on Amazon and you can buy it there. Your model number is KN-138). For oil, I run Rotella Synthetic, but any 5W-40 or 10W-40 will work (the 5 and 10 just designate the temperature at which it will still run well, ie 5 C or 10 C. I live in the north east so I go for 5 for peace of mind). Regardless of which you choose, you'll need about 2.9 quarts for a full (ie with filter) change.
Get some nitrile gloves (especially for spreading oil on the filter when you install it), shop towels for clean up, and you may want to look into getting a new crush washer for the drain bolt (not sure if/when yours has ever been replaced. They can last a while, but it's not a bad idea to replace it if you aren't sure). An oil filter clamp isn't a bad idea to help with getting them off, but I doubt you'll have issue with it. Don’t forget a good oil drain pan (I recommend this one with a screw in, top spout – this is what the oil would drain into – the oil filter holder on the top so it can drain over 24 hours, as well as a front spout), as well as a funnel to help you get the oil in.
Let me know if you need help with anything else. I've found these instructions helpful for those new to it and they are the exact same for you, too. What do you need to change the rectifier for?
I HAVE THE SAME BIKE!
Mine is a GS450TX
TL;DR = fix bike fairly quickly and just ride :)
I hope this helps.
(INCOMING WALL OF TEXT!)
2 years ago I cut my mufflers off and mounted Emgo Shorty's. I also replaced my air box with Uni foam pods. I re-jetted the pilot from 17.5 to 20. I moved the main jet up from 115 to 122.5. I briefly cleaned the carbs with the spray parts cleaner, set the air mixture screws to 3 turns, and reassembled the bike. It ran like crap because I took so many shortcuts. I spent a couple weeks riding and fighting with the bike then I parked it for winter. 2 years went by and I didn't even want to deal with the crappy state my bike was in so I left it parked until we moved (better school zone for kids).
Once we got settled I brought my bike home and started tearing it down.
I spent a couple weeks doing the following:
Bench-sync slide/butterfly valves PDF Guide = http://members.dslextreme.com/users/cbsaunders/gs/gs450_carb_cleaning_guide.pdf
Parts = https://www.partzilla.com/catalog/suzuki/motorcycle/1982/gs450t/carburetor
Rebuild = https://youtu.be/w16in05ANN4
Soak = https://youtu.be/zDkOgnPidPs
Bench-sync = https://youtu.be/AS77T2CUsjI
http://www.jetsrus.com/a_jet_kit_street/suzuki_450_GS450S.html
Test boots for leaks = https://youtu.be/XzjSEYB9RDU
*Modified Uni foam pods: 1) removed half of the inside lip with an knife so the air intake circuit wouldn't be partially obstructed 2) Temporarily restricted Uni pods by taping a ziplock bag around the sides and cutting the bag away from the back end so air intake would be smooth.
Clean tank = https://youtu.be/UpaGo_nq5Rk
https://www.amazon.com/dp/B001KWGA10?ref=ppx_pop_mob_ap_share
https://www.amazon.com/dp/B0041CDW7G/ref=cm_sw_r_cp_apa_i_Pye1CbGHFE87B (buy locally at O'Reilly's cheaper)
(I found a great deal on Kenda Dual Sport K761's at http:/denniskirk.com Front = 100/90-19. Rear = 120/90-17.
Tools needed = Spoons with 2 Rim Protectors https://www.amazon.com/dp/B079JZN5BC/ref=cm_sw_r_cp_apa_i_QEe1CbCMX9JBM
Balance tires easy = E-Z Tire Beads Motorcycle Kit, Ceramic Balancing 2 oz Front + 2 oz Rear. https://www.amazon.com/dp/B00VOAOSDA/ref=cm_sw_r_cp_apa_i_hDe1Cb8QTNKYF
Other notable links:
The GS Resources = https://www.thegsresources.com/
GS Forum = http://www.thegsresources.com/_forum/index.php
Bike Cliff's site = http://members.dslextreme.com/users/bikecliff/
Parts = https://www.babbittsonline.com/oemparts/l/suz/50d3f2caf8700230d8b4bf8c/1982-gs450tx-parts
*** After all this maintenance, my bike starts easily, sounds incredible, shifts wonderfully, is very reliable, and a hell-of-a-lot of fun!
~Best of luck friend~
Thanks for the answer! This is the first time we've been met with a car that recommends a variety of oils. We've only owned Chevy, Jeep, and Toyota in the past and they all have a pre-set oil viscosity they want irregardless of your climate.
I'm in New England USA which means its fairly moderate. Warm summers, chilly winters but rarely anything into the extremes.
Our cars mostly run 5W-30 which is why I was hoping we could get away with using that if it is a direct place in.
I'm thinking of using the Mobil 1 European Formula
https://www.amazon.com/Mobil-120760-Synthetic-Motor-0W-40/dp/B00HG76A9A/ref=sr_1_1?ie=UTF8&amp;qid=1478619568&amp;sr=8-1&amp;keywords=mobil+1+european+car+formula+0w-40
http://www.mercedesmedic.com/how-to-change-oil-mercedes-benz-diy-instructions-video/
Because that website recommended it. But I see it nowhere listed on the MB 229.5 page. Only general Mobil1 shows up there
Thanks!
Edit:
Got the Castrol 0W-40 :) all good
>Can you give me some examples of the cheap purpose made cleaners in case i cant get kerosene?
http://www.amazon.com/DuPont-Motorcycle-Degreaser-Sprockets-11-Ounce/dp/B003OBM5EQ/
http://www.amazon.com/Maxima-75920-Clean-Up-Chain-Cleaner/dp/B000WKATCM/
If you have a combined cleaner and lube that'll work just great. Apply to the inside of the chain, scrub, lube again and wipe clean.
Do your best not to get the lube on the tyres and if you do, clean that stuff off.
I'll preface this with I Am Not a Professional, and my situation involved a bathroom vent fan, not a furnace fan, but I had the same symptoms. Loud humming when it was turned on, giving the fan a manual push would start it for a bit before it would slow down and stop. I suspected that the fan had built up too much dust and the motor couldn't overcome the friction, so I picked up some small motor oil (e.g. https://www.amazon.com/dp/B0083V8MMG) and worked it into the moving parts. After a couple minutes of applying oil and giving the fan some manual help, it was back to normal.
What do the spark plugs look like? Are they fouled at all? If they are clean, you are most likely running completely fine.
The throttle response on 1.8 liter engines is a lot slower than you're used to with a 1.6. It's one of my main points when the classic 1.6vs1.8 threads pop up. I prefer the 1.6 because it's happier to rev and responds quicker. Other people prefer the power.
When you start your car in the video, it sounds healthy. It seems to take quite a normal amount of time to crank and start, and seems happy to do so. I don't think you have a problem there.
Rotella T6 is a well known oil in the NB Miata community. Many people swear by it. It's Shell's high detergent oil. (Yes, it's "Heavy Duty Diesel", but its within the acceptable range of viscosity as well as has API SM qualification for gasoline engines. Plus, hundreds of people here use it)
http://www.amazon.com/Shell-Rotella-550019921-Synthetic-Diesel/dp/B005CHT4W6/ref=sr_1_1?ie=UTF8&amp;qid=1463093322&amp;sr=8-1&amp;keywords=rotella+t6
Thanks guys for answering. This is the one I ordered 2 days ago and had just arrived todayhttps://www.amazon.com/gp/product/B01LH7L0KS/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
I was reading the question and answer section and the reviews section and one guy used it for his 06 subaru wrx sti and he praised this product and said that it helps with the oil consumption in turbocharged engines, and is apparently popular among Subaru car drivers, as there is another guy with an 09 WRX that uses this and praises it as well.
LOL :) and this is why I will always tell people to avoid buying leased vehicles...
&#x200B;
if you want to see how long the car can go without changing oil then ...sure....just be ready to pay for the whole car when you blew the engine...
&#x200B;
You are renting the car pretty much when you are leasing... there's no way the dealer will let you off the hook for negligence.....
https://www.autotrader.com/car-shopping/leasing-car-what-type-damage-will-you-be-charged-216155
&#x200B;
&#x200B;
so if you want to do some basic maintenance... just go by the owner manual
&#x200B;
5000 miles for severe driving or 7500 miles
&#x200B;
0w-20 or 5W-30 vary by countries
&#x200B;
rotate the tires with every oil change (be sure to change the oil filter as well.
&#x200B;
synthetic oil is not that expensive $19 for 5 qt and $9 for oil filter--
&#x200B;
https://www.amazon.com/Castrol-03124-0W-20-Advanced-Synthetic/dp/B00JGQLZJ4
Just understand that the xr650l is really restricted from factory for emissions reasons. If you buy a 100% stock xr650l like I did, expect to spend money/time on doing a couple things. Which, is was fun in my case, built not bought.
If the bike you buy doesn't have these things, expect to do these right off the bat:
REJET! The xr650l runs lean from factory for emission reasons. Running lean is bad for engine overtime (can make engine run hotter than it should and doesn't allow for enough gas to help lubricate the cylinder walls). If anything, make sure this is done first.
Air filter: don't buy the K&N filter. It allow a lot of air flow because it has bad filtration. Yes, it's bad for your engine. Either keep on the stock filter, or go with a UNI foam filter (like I did, and I suggest it)
Again, the engine is restricted from factory, change that exhaust slip-on. Stay with the stock header at first, it's sufficient. I got the EVO-R Big Gun exhaust (loud and proud)
Desmog: You buy a desmog kit off of ebay for like $16. Take off all the emission bullshit and the bike will behave a little better. Takes weight off the bike and looks a lot better without all that clutter
xr650r front stroke or the other one /u/Kilroy_1911 mentioned. If I could go back in time I would get the one that the guy on ADVRider is selling on ebay. The xr650r sprocket doesn't fit perfectly, I had to get an old router bit and grind off some of the inside of the xr650r sprocket for the retaining clip to go on. I went with the Moose xr650r front sprocket
WPS rear brake light. The factory rear brake light thing looks bad IMHO. drill holes and zipties the license plate to the fender. Read the reviews. The stock bulb that comes with it is garbage. Go ahead and order the one they talk about in the comments.
__
That's my "xr650l stage 1 upgrade" suggestion.
Other strong suggestions:
Get some bark busters. They will save your levers and perches. I waited too long to do this and ended up have to replace my clutch perch and clutch/brake levers because dropping the bike on the trail. So, procrastinating on bark busters ended up costing me a little bit of money. Bark busters are a go
If you plan on doing serious trail riding, D606 rear tire is great. Don't get D606 front tire
Changing oil before you drive a vehicle gives you 5+hp, or was that Gran Turismo 3 A Spec? Either way, the manual says to use Honda's GN4 (dinosaur) oil, but lots of people go with Rotella T6 synthetic oil. Without getting into the debate, synthetic oil is better, especially for oil cooled engines, as oil is just as much as a coolant as water in a water cooled engine, and synthetic will cool an engine better than Dino oil will. So, go with T6 oil.
Here's my old write up on my mods (it's outdated to where I'm at with mods)
So would this work?
https://www.amazon.com/Rotella-550019913-Triple-Protection-15W-40/dp/B001B16NP8/ref=sr_1_1?ie=UTF8&amp;qid=1466903849&amp;sr=8-1&amp;keywords=shell+rotella+15w40
I don't know much above this, so it is fine using 15W-40, even if the manual recommends 10W-40.
And what about 5W-40 for the winter, as the above reply mentioned?
And also, I tend to go to places that is ethanol free for gas. Thanks for the help.
I used to always buy those until every can at Walmart started leaking directly from where the nozzle attaches instead of spraying out through the straw, so I stopped buying it. People in the comments also say the formula isn't as good as it used to be. Since then I've been using WD40 as a degreaser which works fine, but kerosene can be used as well.
You're going to save yourself a ton of time with one of these. Get one. Spray, brush, wipe with rag, repeat until clean.
I've been using this every time and it is great. Most people will recommend it. Make sure you get it on the inside of the chain as well as the orings. Gently wipe off the excess so it doesn't fling all over your bike.
That chain of yours looks like death and has probably never been cleaned before. Get as much crap off of it as you can, then see if there's any significant rust or oring damage. If the chain is that bad, I can only imagine the chain slack is terrible. The owner probably also neglected to do simple things such as the brake fluid or coolant, maybe even tire pressure.
Edit: Clean the sprockets while you're at it.
Motul 8100 x clean efe 5w30 full synth.
Usually I do 5w40 t6 rotella, but I have an e-tune with brentunning and this is what they recommend so im gonna give it a shot. it makes sense... idk. I always like having that 40 weight makes me feel a little better... I live in Florida it never really gets cold. But then again I always change my oil around 2500-2800 miles... I drive it pretty hard and I start to get that itch when I get close to 3k. IDK if there's any other addicts out there but im sure someone can relate to my story.
Yes I am very familiar with the XJ650
I recommend valvoline motorcycle 10w40 for air heads. If you don't want to splurge for the motorcycle stuff, just the non-motorcycle version will work fine. (ask 10 people get 11 different answers kinda deal) If you don't have prime, then don't order from amazon.
I would go ahead and change it if you don't know whats already in there.
I would say that if you are very motivated and want to learn and have someone you could rely on to guide you through the work, then you could do it. If the guys at xjbikes aren't completely burnt out by now, then I'm sure that they would love to help guide you through the process.
I seem to remember someone was able to do the job without splitting the cases, but if you drop a part into the crankcase, you'll probably end up having to split them anyways...
EDIT: make sure you know how to bump start so you know you won't get stuck anywhere!
Slick Stacks made by Oil Slick. They make other great products for storing and purging oil as well. I use their products daily and love 'em.
Pep Boys, Advance, and AutoZone all match WalMart prices, at least in my area.
$8 per quart! Kind of baffled that oil costs that much for commercial accounts! Why even have one? Just order Mobil1 on amazon and upgrade to prime -- instant profit margin boost.
Most larger shops in my area have the most common grades of oil in 55-gallon drums or even IBC totes. The large NTB location near me even has a 55-gallon drum of gear oil.
All small desk fans are going to use tiny induction motors with bronze bearings. The induction motor itself will last a long time but the bronze bearings wear out in a few years or less.
If you want to buy a fan and have it last a long time buy a cheap fan from walmart that looks easy to disassemble and lubricate the bearings every once in a while with:
http://www.amazon.com/3-IN-ONE-10045-Motor-Oil-Pack/dp/B0083V8MMG/ref=sr_1_1?ie=UTF8&amp;qid=1393881068&amp;sr=8-1&amp;keywords=3+in+1+motor+oil
I've had great success with the dupont chain cleaner and lube.
26k on my chain right now
http://www.amazon.com/DuPont-Motorcycle-Degreaser-Sprockets-11-Ounce/dp/B003OBM5EQ/ref=pd_bxgy_sg_img_y
First oil change can be early. SOA doesn't mention it but dealers do offer it at varying intervals. I'm in FL and my dealer offered to do it at 1k after the break in period.
I'm doing my own changes and did the first one at 3k and second at 6k to get me back on track. Pretty easy to do on these engines and total cost is about $30: $23 for the oil and $8 for OEM filter, the latter you can probably get a little cheaper from other sites or possibly the dealer.
Thanks a lot, I wasn't aware of that. I use it for track days and DD, I am a beginner at track days so is M1 good for me and I am not in the extreme applications? What qualifies as extreme applications? One session is 30 min and one track event is 8 sessions per weekend, I have done 2 track weekends with M1 oil, how often do you recommend that I change it? also to double check this is what I use https://www.amazon.com/Mobil-94001-5W-30-Synthetic-Motor/dp/B000COX0JM
First off get a 27mm socket for the oil filter cap. I thought I had one that could fit before I started mine but didn't. The oil is kinda hard to find since it needs 5w-40, I ordered some on amazon: Liqui Moly 2041 Premium 5W-40 Synthetic Motor Oil - 5 Liter Jug https://www.amazon.com/dp/B005H2SHS8/ref=cm_sw_r_cp_apa_XlS3xbZ5QE743. The rest isn't too hard, you need to remove the engine cover to give you more working room. To remove the engine cover remove the 2 bolts in top and their is a spot near the rear that just requires a good pull to pop the cover off. I didn't even jack up my Jeep to drain the oil, I think the oil plug was a 13mm, I don't recall but its nothing fancy. The oil filter cap is rather inconvenient to get to but if you have a long socket extension it helps.
That's right, I think people switch over when they start power modding. For stock I would say 5w30 is fine. And yes, the place I had my oil changed used Mobil 1, which I don't prefer. I (and my Subaru) like the Motul much better. I typically Order it off Amazon and I just bring that in to whoever is changing my oil.
Lol what? A quart of synthetic is nowhere close to $30. Here is 6 quarts of Mobil1 for $27.
https://www.amazon.com/Mobil-94001-5W-30-Synthetic-Motor/dp/B000COX0JM
FYI my Tahoe with a 5.7 L V8 took about 6 quarts. 6 quarts will cover MOST vehicles. If you meant to say gallon, then figure around $40 for oil. Another $5-10 for the filter.
So you still save money and know the job is done correctly.
I'm using the T6 synthetic and working smooth. I use subscribe and save from Amazon with a buddy and we buy a few 4 quart jugs every 6 months.
We are using it in a 96 cherokee with 120kand 2 96 grand cherokees with 200k+ miles
https://www.amazon.com/Shell-Rotella-550019921-Synthetic-Diesel/dp/B005CHT4W6/ref=sr_1_2?ie=UTF8&amp;qid=1465582556&amp;sr=8-2&amp;keywords=t6
Hmmm... interesting. I've been using Castrol 10w-40 full synthetic motorcycle oil since i've owned it. This one, right? My oil levels look fine and everything too, though I've heard controversy over the dipsticks in my model? Maybe I should try and add some extra oil to see if it stops it? I don't want to overfill but I also don't want it to be under filled. If it's not the oil, what else could it be?
For the SAI system, are there any drawbacks to bypassing it? Do you have a guide to show how to remove these things and what parts I would need? Thanks for the reply!
-Trackside Front/Rear stands for easy cleaning
I clean and lube the chain about every 500 miles.
Never pressure wash your electrical components (I just don’t pressure wash at all). Other than that, just changing the oil per the schedule and making sure everything runs fine.
Synthetic is usually better for the car and also lasts longer. I use mobil 1 oil filters (get them replaced every two/three oil changes) and I use 5w-30 mobil 1 synthetic oil (lasts up to 5-7k, depending on your driving style). Here's the oil I use, costco is cheapier I belive and here is the link to the Oil filter
how to tell from a good/bad oil filter: it says how much it filters somewhere around the box mobil 1 filters 99.6 percentage (one of the highest)
using these two together I found ran great, the oil lasted the longest (7k miles), I've been experimenting with different filters and oils. you can run 5w-30 is more heat resistant and better in the cold (east coast), 5w-20 is good for California-like weather because it will give you some more MPG. Some people have put 0w-20 but I haven't tried that yet. Also if you take the filter and oil to your dealer they usually do oil changes for 10 bucks.
Okay thanks! Could you possibly provide the Amazon link? I found two listings, one for five quarts and another for 6 quarts which is massively more expensive.
For future reference, these are awesome. And parchment paper works great in the interim as well, though not so much if it's a dryer concentrate.
You can wait until 10K according to VW's Engineers who are way smarter than you or I, or probably most other people on this board.
That being said, I did one at 5k and switched from OEM Castrol to Liqui-Moly https://www.amazon.com/Liqui-Moly-2332-Leichtlauf-Engine/dp/B00LIC29H6/ref=sr_1_2?ie=UTF8&amp;qid=1506552725&amp;sr=8-2&amp;keywords=liqui-moly+5w-40
Napa has it cheaper FYI if you want to buy it locally.
Start with 5 qt of oil for $19. Don't buy a single quart extra -- that gets expensive, just get a second 5 qt and just use that with each change. End result is $3.80/qt, or $20.14 for your car. The $4.86 should be enough for a filter and maybe even wiper fluid.
I have a 2010 S4. Lately I have been running Liqui Moly 5W40. It's a full synthetic german oil, meets the 50200 spec, is cheaper than the audi spec alternatives - and free shipping off amazon!
http://amzn.com/B005H2SHS8
https://www.amazon.com/gp/aw/d/B008MISDH4/ref=yo_ii_img?ie=UTF8&amp;psc=1
6 pack for 51 bucks. Probably the best deal you'll find for this oil
Yep. These cars eat oil. Every 500miles I put 1/4qt of oil or every 1000miles 1/2qt. Check out this oil. I’ve heard good things about it and I’ve been using it Liqui Moly 2331 Leichtlauf High Tech 5W-40 1qt they also sell 5qts
LL 01 is the specification
Castrol EDGE Advanced Full Synthetic "European car formula" is a good one.
https://www.amazon.com/gp/product/B00JGQLZSU
The viscosity could differ based on your local climate.
I have used Mobil 0W-20 in my 2018 for the last two oil changes. I've poured over online threads for all types of Subarus, and found that for the filter it's best to stick to OEM (blue is good, black is better but hard to find). This Fumoto drain plug also makes the process so much easier.
https://www.amazon.com/Valvoline-10W-40-Stroke-Motorcycle-Oil/dp/B00DJ4FGMQ
It's not happening when I shift, it's nothing about a false neutral, I rode the bike for two months, i'm familiar with those. I'm losing the ability to shift at all, it's like once the bike warms up the clutch is stuck pulled like i'm holding the lever when i'm not and the clutch cable has been adjusted
If you understand the ratings then get the bottle that has VW 502 AND 505 on it. Just because it’s 5w-40 doesn’t mean it is what Audi requires. Stop trying to save a few dollars at Walmart and just get LiquiMoly like the rest of us. Liqui Moly 2332 Leichtlauf High Tech 5W-40 Engine Oil-5 Liter, 169.05 Fluid_Ounces https://www.amazon.com/dp/B00LIC29H6/ref=cm_sw_r_cp_api_i_Arz2DbD5QCHX7
If you want to use what Audi dealers use, get Castrol Pro: Castrol Edge PRO OE 5W-40 Quart 502 00 https://www.amazon.com/dp/B077SY4DTN/ref=cm_sw_r_cp_api_i_Vsz2Db2HSCFQT
I would go to ex500.org and register on the forums first. Anyways here's my top mods:
I buy the euro blend castrol for my gti, the 0W-40 5qt jug, and it's only like $25 on amazon!
https://www.amazon.com/gp/aw/d/B00JGQLZSU/ref=mp_s_a_1_1?ie=UTF8&amp;qid=1488127122&amp;sr=8-1&amp;pi=AC_SX236_SY340_QL65&amp;keywords=castrol+0w-40
I have been using this for years on my Minis and never had a problem with it. It was originally recommended to me on the northamericanmotoring.com forums. I highly recommended it too.
I think this is what I'll go with. Also looks like Amazon price matched https://www.amazon.com/Mobil-120760-Synthetic-Motor-0W-40/dp/B00HG76A9A/ref=sr_1_1?ie=UTF8&amp;qid=1484927714&amp;sr=8-1&amp;keywords=Mobil+1+Full+Synthetic+0w40
Also - now that I'm reading more about Rotella T6, it seems like it's for heavy duty engines and diesel engines. Am I looking at the right product? http://www.amazon.com/dp/B005CHT4W6/ref=wl_it_dp_o_pd_nS_ttl?_encoding=UTF8&amp;colid=KVJUPJ7Q9EN0&amp;coliid=I2S2373MP63RJ4&amp;psc=1
I think the GM-LL-A-025 spec is technically obsolete and replaced by the Dexos requirements. Anyways, I source my 0w40 Mobil 1 Euro car formula on Amazon Prime.
https://www.amazon.com/Mobil-120760-Synthetic-Motor-0W-40/dp/B00HG76A9A/ref=sr_1_1?ie=UTF8&amp;qid=1502915673&amp;sr=8-1&amp;keywords=0W40
$22.88 for a 5 quart jug. My 200,000 mile 2.0t seems to like the oil just fine, although I've never ran an oil analysis.
Well this is already turning into an oil thread, so I'll throw in my $0.02.
50 bucks for a gallon of semi-synthetic motor oil?!
Here's some JASO rated fully synthetic oil for ~20 bucks.
VW Turbos need (at least according the VW) pretty specific and expensive oil. Generally that alone is going to be $40 like this. Filter is another $10. So baseline, the parts alone cost $50. Then it's just a matter of being able to do it. I mean, yeah, you can probably go to Jiffy Lube and get a cheaper oil change, but I'd rather pay more for oil and not worry about the turbo eating its self, especially on a 9 year old car.
Yes. This is the 5 Liter jug Liqui Moly Synthetic Leichtlauf High Tech 5W-40 and this is the link for the 1L bottles
Edit: Here’s my post about Liqui Moly Synthetic Leichtlauf High Tech 5W-40 Motor Oil
A little off topic but if you haven't tried it yet, try switching to luqi moly oil. I made the switch to it coming from oem oil and the car is quieter and smoother! This is the one I put in my car. It's a little more expensive but it's straight from germany made for german cars. All the indy's around me use this oil.
A lot of Turbo Subaru guys seem to swear by Rotella T6 and report reduced oil consumption compared to other oils. I've been thinking about trying it on my FXT once the weather improves.
Bring your own oil and filter, get basic change. 5qt mobil 1 is like
$28$23 on Amazon.I use Castrol EDGE 0W40 from Amazon. It’s BMW LL-01 certified, however I’m not sure if that’s the correct weight for your car.
Castrol 03101 EDGE 0W-40 A3/B4 Advanced Full Synthetic Motor Oil, 5 quart, 1 pack @ ~ $26
Either get a chain brush with nylon bristles, or else use an old rag. Apply chain specific cleaner, or else kerosene, or WD-40 to the chain and cleaning tool, scrub the chain. If you haven't touched the chain in a while, you'll probably want to spend around 10 minutes working on cleaning it up. After that, you can either use chain lube or chain wax. Either is fine, it doesn't really matter which you use. Wax does tend to make less of a mess, at least as far as I've noticed.
If you want specific products, here's a chain cleaner,
here's a brush,
and here's chain wax
So $50 in oil and a $10 filter. Yep confirms what I said to someone looking at a boxster, Porsche mechanics are highway robbers.
Here.
The noisy clutch is due to shrunken, dried out rubber dampeners in the clutch basket. There are repair kits available.
Believe it or not, the preferred oil for these bikes is actually [a diesel oil.](
http://www.amazon.com/Shell-Rotella-550019921-Synthetic-Diesel/dp/B005CHT4W6)
To elaborate, Shell Rotella t6 is JASO MA certified.
From Wikipedia:
> For four-stroke gasoline engines, the JASO T904 standard is used, and is particularly relevant to motorcycle engines. The JASO T904-MA and MA2 standards are designed to distinguish oils that are approved for wet clutch use, with MA2 lubricants delivering higher friction performance.
Just stick with Liqui Moly on amazon. I've never seen any European oils in autozone.
https://www.amazon.com/Liqui-Moly-2332-Leichtlauf-Engine/dp/B00LIC29H6/ref=sr_1_4?s=automotive&amp;ie=UTF8&amp;qid=1543619530&amp;sr=1-4&amp;keywords=Liqui+Moly+Leichtlauf+High+Tech+5W-40
You can also get it in the 5 quart size which is generally less expensive. Currently ~$4.58/qt. at Amazon.
Here are the KLR manual specs
Here are the Shell Rotella 15w40 specs
You'll notice that the Rotella 15w40 oil meets the requirements set by Kawasaki by being compliant with [API SH, SJ, or SL] with JASO MA. It has the necessary additives.
TLDR: buy shell rotella 15w40 heavy diesel oil at walmart for $12/gallon, change oil every 2000-2500 miles. Still cheaper than $9/quart
Edit: you can just get it all on amazon.
Prices on amazon go up and down, I've set up alerts and buy when I'm close to an oil change. Here is an example.
You can get this stuff for about $5 a quart. I'd say that's hard to beat. It meets LL-01 standards.
https://www.amazon.com/Castrol-03101-0W-40-Synthetic-Motor/dp/B00JGQLZSU
I've also never had problems with Mobil 1 0W-40, but apparently it doesn't meet LL-01 anymore. But last I checked, the two are almost exactly the same price.
Liqui Moly, the official oil of frickinsweetdude
I've got the same bike, I use this oil: http://www.amazon.com/gp/aw/d/B008MISDH4
With the K&N oil filter: http://www.amazon.com/gp/aw/d/B000E2CVW4
And as for the air filter I stick with the OEM one, you can find it for about $16 online.
picture
Slick Stacks!
Indeed... Shell Rotella (550019921) T6 5W-40 Full Synthetic, Heavy Duty Diesel Engine Oil (CJ-4) - 1 Gallon https://www.amazon.com/dp/B005CHT4W6/ref=cm_sw_r_cp_apa_wGMOyb36R3SYD
[oil] (https://www.amazon.com/Shell-Rotella-550019921-Synthetic-Diesel/dp/B005CHT4W6)
I get the filter from napa. The gold filter. Been using this oil in my 09 tsi for years and in cold buffalo winters.
Oil
Filter
7 quarts + $8 for the oil filter.
http://www.amazon.com/Mobil-120764-Synthetic-Motor-5W-30/dp/B00I4E91GI/ref=sr_1_1?ie=UTF8&amp;qid=1452996179&amp;sr=8-1&amp;keywords=mobil1+synthetic+5w30+5+quart
About $30.
This is what I use for my 2009
https://www.amazon.com/gp/product/B00JGQLZSU/ref=oh_aui_search_detailpage?ie=UTF8&amp;psc=1
I get the filter from my local dealership, or the Mann filter off Amazon/ECS
https://www.amazon.com/Mobil-120760-Synthetic-Motor-0W-40/dp/B00HG76A9A
https://www.amazon.com/Mobil-120760-Synthetic-Motor-0W-40/dp/B00HG76A9A
Hey, you're right. Thanks, no reason to head to Walmart anymore. Oil was the only thing I bought there. I despise Walmart, but at $15-20 cheaper a jug they got to my sellout point.
Here's the link without it referring to OP's wishlist (which causes warnings about adding something that someone has already bought):
http://www.amazon.com/gp/product/B008MISDH4/ref=as_li_ss_tl?ie=UTF8&amp;camp=1789&amp;creative=390957&amp;creativeASIN=B008MISDH4
Edit: Removing referral code, forgot I have a plugin that automatically adds it when copying Amazon links.
I use Castrol 0W-40 in my BMWs. Don't be alarmed by 0W versus 5W. SAE weights are kind of silly. For example BMW's spec basically generates oils in 0W or 5W and 30 or 40 grades even those guys the owner's manual says 5W-30 only. VW spec is probably similar. Basically buy the spec not the SAE grade.
Castrol 03101 EDGE 0W-40 Synthetic Motor Oil - 5 Quart https://www.amazon.com/dp/B00JGQLZSU/ref=cm_sw_r_cp_api_WfXfzbMRKFYXA
Is this the VW spec your car needs?
Meets BMW LL-01, Mercedes Benz 229.5 and 229.3, Porsche A40, VW 505.00 and 502.00, Ford WSS-M2C937-A, PSA B71 2296
10L of synthetic oil + oil filter? I mean it's also $100 in Canadian dollars if that makes any difference. It's actually low when I look up actual prices.
Liquimoly, which I prefer, is listed at $66 for 5L on Amazon Canada. So I'd need 2 of those, which is $132. Then a filter which is about $10.
A $142 (call it 150 w/ taxes) isn't out of range for a vehicle that originally retailed for a bit over $100k (Canadian).