Reddit mentions: The best masking tape
We found 282 Reddit comments discussing the best masking tape. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 165 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. ISC Racerstape Surface Protection Tape / Helicopter Tape 2 Inch x 12 Feet
- Core: 3 inch diameter
- Backing/carrier: polyurethane film
- Adhesive: acrylic
- Release liner: 92 lb. Polycoated white paper
- Thickness: 12.7 mils (carrier, adhesive, liner) 8 mils (carrier, adhesive) 4.7 mils (liner)
Features:
Specs:
Color | black |
Height | 1 Inches |
Length | 1 Inches |
Number of items | 1 |
Size | 2 in. x 12 ft. retail package |
Weight | 0.25 Pounds |
Width | 1 Inches |
2. 3M Scotch 5952 VHB Tape: 1 in. x 15 ft. (Black)
3M 5952 Heavy Duty Mounting VHB Tape is black, double-coated VHB adhesive tape with an acrylic foam core. A modified acrylic adhesive is on both sides of very conformable foam which provides adhesion to the broadest range of substrates/surfaces, including most powder coated paints. It comes on a red...
Specs:
Color | Black |
Height | 0.98425 Inches |
Length | 4.7244 Inches |
Number of items | 1 |
Size | 1 in. x 5 yds. 5-yard roll |
Weight | 0.220462262 Pounds |
Width | 4.7244 Inches |
3. ScotchBlue Original Painter's Tape 2090-18NC, 0.70 in x 60 yd (18mm x 54,8m), 1 Roll
Designed for use on multiple surfaces such as smooth or lightly textured walls, trim, baseboards, tile and glass14-day clean removal leaves behind no damage or sticky residueMedium adhesiveUV and sunlight resistantSize: 0.70 in. x 60 yd.CREATE SOCIAL DISTANCING MARKINGS: Create box or “X” queues...
Specs:
Color | Blue |
Height | 4.69 Inches |
Length | 0.7 Inches |
Number of items | 1 |
Release date | August 2019 |
Size | .70 inches x 60 yards, 2090, 1 Roll |
Weight | 0.15 Pounds |
Width | 4.69 Inches |
4. 3M RP25/GRY055 Scotch RP25 VHB Tape: 1/2" x 15 ft.
- Carrier/backing: closed-cell acrylic foam (conformable). adhesive: multi-purpose acrylic
- Adhesion: 272 ounces per inch (to stainless steel test panel). tensile strength: 90 pounds per inch (longitudinal). thickness: 25 mils (carrier, adhesive)
- Service/operating temperature: up to 200F. Short term temperature resistance: up to 250F. Application temperature: 60F to 100F
- Density: 45 pounds per cubic foot. Dynamic overlap shear: 80 pounds per square inch
- Release liner: red film (1/2 inch wide), white paper (3/4 and 1 wide)
- Please note that 3M supplies RP25 1/2-inch on a white liner or a red liner. The product is the same for both liner colors
Features:
Specs:
Color | White,Red |
Height | 0.5 Inches |
Length | 4.13 Inches |
Size | 1/2 in. x 5 yds. 5-yard roll |
Weight | 0.09 Pounds |
Width | 4.13 Inches |
5. ScotchBlue Original Multi-Surface Painter’s Tape, 2090, 2.83 inch x 60 yard, 1 Roll
- Designed for use on multiple surfaces such as smooth or lightly textured walls, trim, baseboards, tile and glass
- 14-day clean removal leaves behind no damage or sticky residue
- Medium adhesive
- UV and sunlight resistant
- Size: 2.83 in. x 60 yd.
Features:
Specs:
Color | Blue |
Height | 4.69 Inches |
Length | 2.83 Inches |
Number of items | 1 |
Size | 2.83 inches x 60 yards |
Weight | 1 Pounds |
Width | 4.69 Inches |
6. ScotchBlue Original Multi-Surface Painter’s Tape, 2090, 1.88 inch x 60 yard, 1 Roll
14 day clean removal leaves behind no damage or sticky residueMedium adhesiveUV and sunlight resistantSize: 1.88 inches x 60 yardPack Size: 1 Roll/PackTape Removal Tips: Wait until the paint is dry to the touch before removing the ta Tape Removal Tips: Wait until the paint is dry to the touch before...
Specs:
Color | Blue |
Height | 6 Inches |
Length | 6 Inches |
Number of items | 1 |
Size | 1.88" Width |
Weight | 0.6 Pounds |
Width | 2 Inches |
7. 3M Vinyl Tape 471+ PN6404, 1/8 in x 36 yd (Pack of 1)
Provides clean removal without adhesive residue after a 30-min. Bake cycle at 250°F/121°CFlexible and conformable tape creates fine paint lines for striping, color separation and complex designsSemi-translucent backing allows for accurate alignment with simple and complex patternsResists lifting f...
Specs:
Color | Blue |
Height | 4.62598424725 Inches |
Length | 0.12598425184 Inches |
Number of items | 1 |
Size | 1/8 in x 36 yd |
Weight | 0.2 Pounds |
Width | 4.62598424725 Inches |
8. Nitto (Permacel) P-02 Double Coated Kraft Paper Tape: 1 in. x 36 yds. (White)
Nitto P-02 Double-Sided Kraft Paper Tape is a highly versatile, 2-sided flatback paper tape with extremely aggressive adhesion, making it ideal for various holding, mounting, splicing, fastening and laminating applications.Nitto P-02, previously known as Permacel P-02, is made from paper that has be...
Specs:
Color | White |
Height | 1 Inches |
Length | 5.75 Inches |
Weight | 0.6 Pounds |
Width | 5.75 Inches |
9. Ampro A1441 PTFE Seal Tape 1/2-Inch X 260-Inch
- Dimensions: 1/2" X 260"
- Adds extra Seal at threaded joints
- Teflon tape
Features:
Specs:
Height | 3.54 Inches |
Length | 4.92 Inches |
Number of items | 1 |
Weight | 0.05 Pounds |
Width | 0.98 Inches |
10. Double-sided Tape for Strong Adhesion to Peel Off T3830 15mm×10m
- Hex stainless steel handle
- precision
- Stainless steel points
- Fixed stainless steel handle and stainless steel point
- 25Mil with stainless steel handles, 6 probes
Features:
Specs:
Color | Clear white. |
Height | 0.0062992 Inches |
Length | 393.7 Inches |
Width | 0.59055 Inches |
11. 3M Scotch-Blue 2090 Safe-Release Crepe Paper Multi-Surfaces Painters Masking Tape, 27 lbs/in Tensile Strength, 60 yds Length x 3/4" Width, Blue
3M2090-.75EBuilders TapeBlue
Specs:
Color | BLUE |
Height | 4.8 Inches |
Length | 4.8 Inches |
Number of items | 1 |
Size | Pack of 1 |
Weight | 0.15 Pounds |
Width | 0.75 Inches |
12. 8 of VHB 3M Adhesive 1.5 x 1.5 inch Double-Sided Tape Dots High Bond Conformable Acrylic Glue Replacement Kit Square Plus Alcohol Pad
✓ Suitable for bonding many kinds of material with flat hard surface✓ Double sided self sticky✓ Alcohol pad included✓ Easy to use✓ Satisfaction or money back guarantee.
Specs:
Color | Dark blue |
Height | 4 Inches |
Length | 6 Inches |
Number of items | 8 |
Size | Square: 1.5 x 1.5 inch |
Weight | 0.0551155655 Pounds |
Width | 0.2 Inches |
13. Scotch Masking Tape and Paper Dispenser with 6 in Blade, M1000-SBN
- Simultaneously applies masking paper with masking tape to cover and protect various surfaces in one easy step
- Great for covering a variety of surfaces with masking paper including windows, baseboards and door casings
- Has a 6 in. plastic blade with a 6 in. extension
- Dispenses paper up to 12 in.
- Includes: 1 Dispenser, 1 - 6'' Blade, 1 - 6'' Extension Blade for Wider Papers
Features:
Specs:
Color | Blue |
Height | 4.75 Inches |
Length | 12.05 Inches |
Number of items | 1 |
Size | Masking Tape & Paper Dispenser |
Weight | 0.75 Pounds |
Width | 5.5 Inches |
14. Frost King V27WA, White EPDM Rubber Self-Stick Weatherseal Tape, D-Section, 9/16" W, 5/16" T, 10 ft L, 1
- High compression product - spring back to shape ever after long exposure to subfreezing conditions
- It will not harden, crack or freeze even at 40 below zero
- Can be applied to interior or exterior surfaces
- Fills irregular and wide gaps
- Fits wide gaps
- Long lasting
- Will not crack or freeze
- Retains shape after freezing
- Fits one average window or door
- Fits wide gaps
- Long lasting
- Will not crack or freeze
- Retains shape after freezing
- Fits one average window or door
Features:
Specs:
Color | White |
Height | 9 Inches |
Length | 1 Inches |
Number of items | 1 |
Size | 1 |
Weight | 0.03 Pounds |
Width | 8 Inches |
15. C.R. Laurence 1/2" Bond Breaker Tape By HandsOnCo
- Use in Shallow Joints and Metal Butt Joints
- Used to Create Proper Two-Way Sealant Bond
Features:
Specs:
Color | clear |
Number of items | 1 |
Weight | 0.19 Pounds |
16. ProTapes Pro Scenic 714 Crepe Paper 14 Day Easy Release Painters Masking Tape, 1" Width
Excellent conformabilitySmooth backing for superior paint lines and reduced fingertip abrasionConsistent/easy unwindResistant to humidity and paint bleed-throughSecure adhesion and stain resistant
Specs:
Color | Blue |
Height | 1 Inches |
Length | 4.7 Inches |
Number of items | 1 |
Size | 1" Width |
Weight | 0.7 Pounds |
Width | 4.7 Inches |
17. Suck UK Sushi Tape | Decorative Paper Washi Tape | Novelty Masking Adhesive Tape | Set of 4 Quality Tapes | Quirky & Cute Design
Set of 4 decorative paper washy tape / masking tape in different sushi designsEach tape measures 10m - use as decorative additions to your wrapping or notebooks / notepadsA surprising gift for sushi fans everywhere – if you’re a lover Japanese culture or food they are the perfect addition to you...
Specs:
Height | 1.77 Inches |
Length | 0.91 Inches |
Number of items | 4 |
Release date | January 2019 |
Weight | 0.0375 Pounds |
Width | 1.77 Inches |
18. HIQPARTS (high queue parts) Sujibori guide tape 3 mm x 30m winding (1 pcs) [CGT-3MM]
Specs:
Height | 0.39 Inches |
Length | 6.06 Inches |
Weight | 0.06172943336 Pounds |
Width | 3.66 Inches |
19. Scotch Rough Surface Extra Strength Painter's Tape, 0.94 in x 60 yd, 2060, 1 Roll
Designed for use on concrete, brick, stucco, and rough wood5-day clean removal leaves behind no damage or sticky residueVery strong adhesiveRecommended for use with or on lacquer coatingsBonds aggressively, yet has a smooth unwindSize: 0.94 in. x 60.1 yd.CREATE SOCIAL DISTANCING MARKINGS: Create box...
Specs:
Color | Green |
Height | 5 Inches |
Length | 5 Inches |
Number of items | 1 |
Size | 0.94" Width |
Weight | 0.37258122278 Pounds |
Width | 1 Inches |
20. XFasten Conductive Copper Tape, 1-Inch x 12-Yards, Slug Repellent, DIY Material, Electronics Repair and Stained Glass Making
SOLUTION TO EMI AND RFI ISSUES. Prevent further inconvenience and damages to your devices due to electromagnetic and radio frequency interference. The XFasten EMI Shielding Copper Tape offers a quick but long term solution to your electronics with its EMI shielding properties. And do not worry if yo...
🎓 Reddit experts on masking tape
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where masking tape are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
You mentioned that you may be a beginner, so if you are not, forgive me. I will try to cover as much as I can about painting a wall, and hopefully what you need will be in here somewhere.
---
First things first, you will want some rollers and trays, and you will want some brushes. Look for something that is springy, and strong. When you run your fingers along the bristles, you want them to bounce right back up after your touch. You will get what you pay for, so it is worth it to invest in good brushes. If you care for them, and clean them well, they will be good brushes for you for life.
---
To tape or not to tape: I personally hate taping. I find that it takes way too long to set up, and people get overconfident that the paint will not seep under the tape and effect the adjacent wall/ceiling/molding. In my experience, it still makes a crappy edge, and its just too much of a hassle.
The only place I use tape is on things that can get dripped on like molding or flooring. There is a dispenser you can purchase where you can combine your painters tape with a roll of paper attached and that is what I use. Its quick, and easy, and worth it so you don't spend a million hours setting up, and a million more hours cleaning after.
If you must tape, buy blue painters tape so you don't fuck up the walls you are not painting. You want to put the tape on the wall you don't want to put color on. Put the edge of the tape as close to the corner of the wall as possible, as straight as possible, and rub down really really hard on the tape so that it is less likely for paint to seep under the edge. Seriously, though, it takes forever, and it really isn't worth it.
So what do we do with the edges of the walls if we're not taping? Worry about that later, it'll come in a minute. First you have to get comfortable with your tools.
---
Ok, so you've removed everything from the room, and put paper and plastic down so you don't drip on the floor. (Or, alternatively, you've moved shit out of your way, and covered it in painters cloth or plastic or something. It may not be near the wall, you're painting, but cover it anyways; you don't want to have to regret accidental spills of paint.)
Now we can get to fucking around with paint. First, practice putting paint on the rollers and on the brushes, and use the middle of the wall you're going to paint as your practice area. The goal is to just get comfortable with painting a wall by messing around with rollers and brushes in a harmless area. You'll get used to how your rollers and brushes will work, and you'll feel a lot more confident. A lot of painting a wall is about confidence, surprisingly.
With the brush, avoid getting paint all the way up to the handle of the brush. Leave about a half of an inch to an inch of bare brush any time you apply paint. You're only painting with the bristles, don't waste paint by putting it on parts of the tool you won't be painting with.
Practice painting all kinds of strokes. Wide strokes with the wide part of the brush; thin strokes, where you hold the brush like a pen, and draw a thin line... Try writing stuff, and drawing pictures. It'll help you get a feel for what works and what doesn't with the brush.
With the roller... well, put some paint in your pan, and just practice getting an even amount of paint on the thing. Roll the thing out in the pan, and practice putting it on the wall. Its pretty straight-forward, and you'll get the hang of the difference between too much and not enough paint quickly. If you get drips on the wall, roll the brush out on the pan some more to remove excess paint, and use the roller to even out the drips.
---
When you finally feel comfortable, and you get a good sense of how good your hands are, you can move into actually seriously painting the wall.
Lets get back to doing the edges of the wall. So what do you do if you're not taping a wall? There is a technique called "cutting in" or "cutting a wall." This guy will explain it a lot better than I.
Basically, you use the brush like a marker down the edge of the walls to make a line. You want to go slowly, and pay attention. When you put the brush against the wall, notice how the bristles will gently push out in all directions. Use the edge of the brush, and the corner of the wall to your advantage, and you'll make a nice clean, professional looking line. Here is another, very informative video to help you out with this. If you are concerned with how good you are at cutting in, practice cutting in by making a border around the practice mess you made in the middle of the wall. Once you get used to making a practice boarder, give the edges a try. The worst that will happen is that you will need a wet rag to wipe paint off the other wall.
Once you cut in all your edges, you can use the roller to roll on the rest of the wall.
You will end up doing several coats of paint on the wall. If the room is not well ventilated, bring in a fan or something to help move air around. It'll help you breathe, and it'll help the paint dry faster.
This is BASICALLY how you paint a wall. You may want to look to home improvement websites or youtube for more videos if you need more illustrations/how-to's.
It can be fun, so let it be, and avoid drawing anything too risque on the wall in the office if you have to leave it for any amount of time to dry.
Hope this all made sense, and Good luck!
---
tl;dr. Cut in your edges first, then roll paint on the walls. Fuck painters tape.
Weather stripping would do it I think. Even Home Depot probably has one thick enough for that, but if not then I'm sure Amazon would.
On the top you could probably rest a draft guard. They are usually for the bottom of the door, but it looks like you could fit one on top. This DIY approach might work better due to gravity. You'll have to go to the plumbing section for the styrofoam pipe insulation, but it's only a few dollars for a 6 foot length. Heck, you might even be able to use that on the side of the door if you tape it in place.
Personally I don't like the typical flat weather stripping. I like the bristle kind or the 3D kind like this or this.
And I've never used it, but something like this could work too. I bet you could stick it on the side and top of the door.
Good luck, and I still think it would be best if your landlord took care of it if possible.
Rope-caulk is a great immediate solution for cold-weather, but not convenient long-term for windows that get opened regularly.
I hate it when I drive through a neighborhood of historic architectural interest and find that homeowners have replaced rolled-steel windows -- which were an important aspect of the house's architectural style -- with some modern bright-white replacement windows with an extra few inches of the window perimeter taken up by white plastic instead of glass. I can't imagine that the reduced light makes the interiors of the house any nicer either.
There are plenty of ways to maintain and upgrade the original windows, or replace them with visually equivalent but modern products from Crittall, OptimumWindow, etc.
Advice from the publication The Preservation of Historic Architecture: The U.S. Government's Official Guidelines for Preserving Historic Homes is this:
>Appropriate types of weatherstripping for metal windows:
>SPRING-METAL comes in bronze, brass or stainless steel with an integral friction fit clip. The weatherstripping is applied after the repaired windows are painted to avoid galvanic corrosion. This type of thin weatherstripping is intended for windows in good condition.
>VINYL STRIPS are scored and fold into a "V" configuration. Applied adhesive is necessary which will increase the thickness of the weatherstripping, making it inappropriate for some situations. The weatherstripping is generally applied to the window after painting.
>Closed cell FOAM TAPE comes either with or without an adhesive backing. It is effective for windows with a gap of approximately 1/4" and is easy to install. However, this type of weatherstripping will need frequent replacement on windows in regular use. The metal section should be cleaned of all dirt and grease prior to its application.
>SEALANT BEAD. This very effective type of weatherstripping involves the application of a clean bead of firm setting caulk on the primed frame with a polyethelene bond breaker tape on the operable sash. The window is then closed until the bead has set and takes the form of the gap. The sash is then opened and the tape is removed leaving the set caulk as the weatherstripping.
Acrylic panes on the inside mounted with magnet tape are a great upgrade for both thermal performance and infiltration issues. A notch out of the acrylic rectangle is necessary for the latch-position, but can be air-sealed against the adjacent class with foam tape.
So it was recommended you get painting tape so the wood doesn't come up and stuff (I have no idea what that's about but it's what I read) so this was the tape. This is the drill I used to make the hole. And here is the grommet I used to fill the hole (heh heh heh). All in all, a very easy process and makes it look really clean.
The 1080 is great. I am coming from a 970 but it wouldn't drive the Dell u3415w very well at 3440x1440 but this card does it no problem. I have been playing Mirror's Edge Catalyst, Witcher 3 and Fallout 4 for the most part and everything looks fantastic at high resolutions. The card is also super quiet.
If you were interested in the case, it's over here. I like it a lot but like I said in a previous comment, it was given to me but I agree with the finish, it's really good.
There's a lot of ways to approach stenciling. I just started about 5 months ago and have a decent number of pieces completed, but i'm still learning each time I cut and paint.
I'll be happy to share a list of what I use, but just keep an open mind and remember that there's not just a single way to do this.
[] Materials []
(https://www.amazon.com/X-ACTO-Designer-Hobby-Craft-X3254/dp/B002A2QTGK/ref=sr_1_22?ie=UTF8&qid=1501185899&sr=8-22&keywords=xacto+11+knife)] [link]
[] General Tips []
Hope this is helpful, remember to share your pieces!
Oooh! I like the darkness in your soul 😁😁😁 wasabi oil in the eyes is GENIUS
To get close enough to them, we could wear these to fit in 😊
And then once they are down from the wasabi oil, we can tie their hands and legs up with this Sushi washi tape 😁😁😁😈😈😈
I believe I have finally decided on my first Gunpla, the HG Age II Magnum and want to make sure the items I have added to my Amazon cart are ideal or not for a beginner/future use for HG and MG kits. The list is as follows:
I know that this sub has a list of tools and tutorials, but because I'm trying to budget, I was thinking no more than $100 would be ideal for me to start with. Since I'm beginning with HG models, I don't think I need a full set of Gundam markers, but if it's needed/required/highly suggested, I might pick them up as well.
So I have read and seen that top coating and panel lining are essential for MG models to make them pop. Are they just as essential for HG model kits? Looking at pictures of the Age II Magnum I'm planning on getting from Amazon, it doesn't seem to have a lot of indents for panel lining. Of course, I could be wrong and be blind as a bat. If I don't do any sort of panel lining, is it still a good idea to add a top coat regardless?
Also, how soon can one get into MG kits? I was originally going to jump straight into either the MG GM Sniper II or the RX-78-2 Ver 3.0 but after doing some research over the past few days, I've decided I'll be doing a few HG's to begin with as I haven't built model kits since I was like 7 or 8 with my dad. I'm thinking after the Age II Magnum, I was thinking about getting either the HG Double O Diver or the HG 00 Shia Qan[T]. Maybe after I complete the 3 HG's I've listed, is it possible to jump to the the GM Sniper II?
TL;DR:
Patience and practice. Scribe the back of plastic spoons for practice, or any other round plastic objects.
But I do recommend using proper modeling scribing tape like this one instead of Dymo tape. Dymo tape works fine for flat surfaces, but this scribing tape is a lot more flexible and will conform to curved surfaces better. They last quite a while depending on how much you scribe. I bought a roll last year and still haven't run out after 3 MG builds I scribed heavily.
Secondly, if you're using this Tamiya scriber, you might want to change it to something like the Tamiya engraver or something similar. They're much easier to control over a tool like the Tamiya scriber and you can change the blades to suit the thickness you want or need for your kit. Mr. Hobby makes a similar tool that's a bit cheaper I think, and obviously there are BMC chisels which are the top of the line. But there are cheap alternatives out there.
Honestly though, when it comes to precision tools like scribers it might be best to go out and buy the highest quality scribers/chisels you can afford. Buying lower quality tools can actually get you bad panel lines.
From the reviews, it looks like it doesn't work a damn for lots of people, though some report good success. I'm guessing that they just import whatever from wherever, stick their name on it, and sell it in a colorful blister pack. (What QC?)
I guess if it were me and I had a slug problem in my area (I'm lucky), I'd be looking at a more-industrious source. This stuff looks like a winner. I say this not because I've used it, but because it says "safe for soldering," claims to have conductive adhesive, and is therefore likely to be actually-bare copper for all the electronic/industrial uses that require such a thing.
And for a sure thing, there's always McMaster-Carr: https://www.mcmaster.com/#copper-foil-tape/=17zrfgi These guys don't fuck around when it comes to material descriptions.
Good luck!
It's very simple. Get something like this and then this for the smaller stripe.
You could do it without a clear coat but the clear coat will make it more resistant to pealing/chipping/more permanent. If you do decide to do a clear coat it's not coming off unless you sand the clear coat and your paint off.
Most helmets/bikes come like this from the factory with their vinyl stickers etc placed on and then just clear coated over.
http://imgur.com/a/EMEaU
This is a christmas light I printed as a gift for my Grandma on a Rostock V2 Max.
I used cheap white PLA from bgastore on ebay (link later).
I designed the file in Autodesk Inventor 2017 Student Version and in Meshmixer. I also used Meshmixer to create the custom supports for the model. http://www.thingiverse.com/thing:1914863
The model was printed on Blue Tape with no glue or bed heat.
Support removal took around 3 hours, I started with the middle, then went around the text and then finished up at the top of the model. I used needle nose pliers and wire cutters I would not recommend printing this unless you have both.
Afterwards I used acrylic paint to paint over the text. The surface was rough if you’re planning on painting this model I would recommend sanding it first.
The print can be kept as a christmas tree ornament or as a light. It’s possible cut a hole in it to fit a large lightbulb in or order a small one off of amazon. Make sure the bulb doesn’t touch the sides of the print as it can melt the plastic.
Cura Settings:
Layer Height: .3mm
Line Width: .5mm
Wall Line Width: 1mm
Top/Bottom Thickness: 2mm
Infil: solid
Print temp : 205
Build Plate: 0
Retraction speed: 50mm/s
Extra Prime amount: .1mm
Minimum Extrusion Distance Window: 6.5mm
Speed: 30mm/s
Wall Speed: 15mm/s
Initial Layer Speed: 8mm/s
Combing mode: all
Z hop when travelling: 2mm
Cooling: fan 100%
No support, the meshmixer supports are enough
Brim: 1mm
Link to plastic:
http://www.ebay.com/itm/like/391087201228?lpid=82&chn=ps&ul_ref=http%253A%252F%252Frover.ebay.com%252Frover%252F1%252F711-117182-37290-0%252F2%253Fmtid%253D1588%2526kwid%253D1%2526crlp%253D145795696709_324272%2526itemid%253D391087201228%2526targetid%253D265536273303%2526rpc%253D0.08%2526rpc_upld_id%253D91336%2526device%253Dm%2526mpre%253Dhttp%25253A%25252F%25252Fwww.ebay.com%25252Fulk%25252Fitm%25252Flike%25252F391087201228%25253Flpid%25253D82%252526chn%25253Dps%2526adtype%253Dpla%2526googleloc%253D9005779%2526poi%253D%2526campaignid%253D672333784%2526adgroupid%253D29658622530%2526rlsatarget%253Dpla-265536273303%2526gclid%253DCj0KEQiA08rBBRDUn4qproqwzYMBEiQAqpzns6jXyE4PiaoJpcMmUbU6nRO9XAd2FxXUSDttHbQfGFAaAjGt8P8HAQ%2526srcrot%253D711-117182-37290-0%2526rvr_id%253D1127005495389&ul_noapp=true
Tape:
https://www.amazon.com/ScotchBlue-Painters-Multi-Use-70-Inch-60-Yard/dp/B00004Z4BB
3M VHB tape is the best
VHB stands for Very High Bond, it sticks amazingly well to smooth surfaces like a kwad frame but when you want to remove it you can peel it off pretty easily. It isnt going anywhere when you fly. It is also a little foamy so it provides a little cushion bten the carbon fiber and electronics.
https://www.amazon.com/dp/B01BU7038A/ref=cm_sw_r_em_apa_i_hQ4jDbV2SB64H
I just got a new bike and felt the same way for a while. After some research I found this: ISC Racers Tape/Helicopter Tape. A number of people online seem to like it.
After getting used to the fact that I will probably bang up my bike a good bit more and I might as well get over it, I decided to buy a little anyway. I'm going to put it on a few spots I worry about i.e. to prevent chainslap and where the bike touches my bike rack. Might as well make a small effort to help the resale value if I ever want to sell it.
FYI helicopter tape is pretty useful for covering up areas where paint can chip from rocks, debris, and chain-slap. It’s the same stuff used to protect phone screens from wear and tear, and apparently helicopter blades. This roll is way cheaper than the made-for stuff.
Entry Level
Advanced Mode
Advanced mode + Fretwork
Advanced Mode + Burning the shit out of yourself and getting really mad about tiny things and also not being 100% sure which humbucker wiring diagram applies to the pickup you're installing because the colors don't match what you found on that one chart online and also you might have destroyed the cap on your tone pot
Sweet. I was looking at this, but yours has better reviews. I'll give it a shot. Thanks!
Maybe just a brand thing. I'm using the Scotch Blue painters tape: https://www.amazon.ca/gp/product/B001EJMS4M/ref=ppx_yo_dt_b_asin_image_o03_s00?ie=UTF8&psc=1
I don't know if Id recommend it though. In my limited experience Its hard to get fine details in the first layer like holes or text to stick unless you rubbing alcohol the tape first, but when you do large surfaces stick too well and you'll have a hell of a time to get them off. I started using this glue stuff that came as a sample pack in a couple of my 3dprintingcanada.com orders but decided it wasn't worth the mess and hassle. Others have had success with hairspray so I'd give that a shot first.
I miss the stock flexible magnetic build tac that comes with the Ender 3 pro, so I ordered a replacement that I'm going to stick on top of the glass. My bed was so warped from factory that I could almost stick a dime in the middle under a straight edge. Hopefully with a magnetic build tac on top of the glass Ill have the best of both worlds. My temps will suffer and it will be a little heavy but I'm willing to experiment.
Try this 3M double-sided tape[https://www.amazon.com/dp/B00WX1P0GS/ref=psdc_228921_t2_B004BN81LC] instead of the regular electric tape. Its more flexible and strong. Just wrap up the whole cable with this and you'd be happy for couple of years.
Definitely tape the fretboard off with painter's tape! It's specifically designed to seal/stick well and release cleanly/easily. Aside from using it to tape off guitar necks, as a former roller derby ref we used it to tape down tracks on top of expensive roller skating rinks floors. Always came up easily!
A regular one might, not sure, but you can always get something like this if you want to be extra safe.
I've been using Nitto Tape and that stuff is pretty amazing.
Did you save it, or is it gone? It can be reattached if not lost or damaged. Get some of this stuff to replace the original tape.
Ah, it looks like that case came with Canadian purchases only. Best Buy's CA website won't ship to me, and and my local site doesn't carry the case.
At any rate, you can purchase the 3M adhesive strips separately.
http://i.imgur.com/eYWjcZE.jpg
While this can't fix the existing scratches, if you are serious about protecting your frame then consider applying some helicopter/racer tape to the most vulnerable areas.
It's basically a thick version of protective films they use on electronic screens. UV stable and can take a beating. Bonus is that it peels off without hassle or marks. A lot of the guys in my area use it to protect their carbon frames. Just clean the application area well with alcohol before putting the tape on.
http://www.amazon.com/ISC-Racerstape-com-Paint-surface-guard/dp/B000TPC7HU
Nitto Permacel P-02
There is no substitute. Thin, rock solid holding requiring very little tape, and easy release with no clean-up. Pricey though. but awesome.
https://www.amazon.com/Nitto-Permacel-Double-Coated-Kraft/dp/B000QDL9GK/ref=sr_1_1?s=industrial&ie=UTF8&qid=1492621121&sr=1-1&keywords=nitto+tape
This stuff is the best for sharp crisp lines, i use it for automotive graphics as well as my models.
Sorry Reddit didn't show me any notifications, just came across this on my feed (mobile... ffs)
As the other reply says though, Amazon for the win! Got it on Amazon Canada, Just looked for the widest I could find
Scotch-Blue Painter's Tape, Multi-Surface, 2.83-Inch by 60-Yard https://www.amazon.ca/dp/B001EJMS4M/ref=cm_sw_r_cp_apa_-.fWAbJ8PXT9M
I use double-sided tape, like [this one](3M Scotch RP25 VHB Tape: 1/2 in. x 15 ft. (Grey) https://www.amazon.com/dp/B00WX1P0GS/ref=cm_sw_r_cp_api_0zBEAbQDWXD9D). I usually put 4 pieces on, one over each screw that secured around the processor. Holds really well. This is what most of the modders I follow use.
>... I just reenter it and it stays.
Have you tried using some 3M double sided tape on the sides to improve adhesion? Just those three small strips hold that thing down like an anchor.
You could use double sided tape like this: https://www.amazon.com/3M-Scotch-5952-VHB-Tape/dp/B01BU7038A/ref=sr_1_3?s=industrial&ie=UTF8&qid=1517867355&sr=1-3&keywords=3m+vhb
The con is that you might not be able to remove it so easily. This stuff is pretty extreme.
I'm using this tape to cover the back for now, and it is a lot grippier than the bare aluminum, the back glass, or even my plastic screen protector. If they use a similar material it should have some grip. "Self-Healing, flexible, tough, military-grade thermoplastic urethane, designed to absorb impact" sounds grippy. Good point about peeling. Maybe clear adhesive film for the back plus a bumper case would be a good combo.
I have Thule Atmos X3 case on my old phone, and it's awesome. It's thin and unobtrusive (adds maybe 2-3mm thickness), but it protected that phone every time I dropped it. It's made of high quality co-molded materials with a subtle design and variety of textures. Too bad they seem to have given up on Android phones.
This stuff, aka painter's tape, for those that don't wanna click.
Edit to add - vinegar also helps remove rust, and if you're afraid steel wool will be too abrasive, use aluminum foil as your scrubber. Foil and vinegar is a long-standing rust removal tool, but use only tiny amounts of vinegar, you don't want it to drip down along the side of the pole inside the pickup.
Add'l edit to add - anything that removes the rust is going to make it go somewhere - I read that having a vacuum running while you do it is a good precaution to keep the tiny rusty bits being removed from getting everywhere.
This is the exact thing I got.
Kind of pricey but it seems like the roll will last for every bike I ever own.
I use ISC Racers Tape.
https://smile.amazon.com/dp/B000TPC7HU/ref=cm_sw_r_cp_apa_i_595SCbRDHK3ZP
Not just water, but slightly soapy water. It breaks the surface tension on the water allowing it to completely cover the adhesive so you can easily position it on the frame. Lots of soapy water. You can't use too much. Be careful not to get water on the backing paper before peeling off the tape. It has a tendency to pull apart and stick to the tape if you get it wet. If your hands are wet with soapy water you can handle the adhesive side without leaving fingerprints. I use a dish towel to squeegee and dry around the edges. It won't start to stick well until it squeegees out and dries. If it slips when your squeegeeing splash more soapy water on it and have another go at it.
I just wrapped a new steel hardtail in 1", 2", and 4" tape because it's gonna take a thrashing.
I use this tape which is just 2 inch wide blue masking tape. I got it at Target but they sell it a lot of places. I don't know if there's a better kind, that's just what I had on hand... how wide is the stuff you use?
It's a little pricey, but I've heard good things about helicopter tape:
LINK
https://www.amazon.com/3M-ScotchBlue-Painters-Tape-Multi-Surfaces/dp/B00004Z4BB?th=1
This stuff is an absolute godsend for dorm walls
Or https://www.amazon.com/gp/product/B000TPC7HU if you don't like black ;-)
I'd also recommend taping the entire bike with it anyway because paint chips even more quickly when you bikepack haha. (Or at least, the down tube and the chainstays in addition to where the bags touch the frame)
You can get clear 'helicopter' tape from Amazon for a reasonable price to replace that, and maybe add some to the underside of your downtube, too, if it doesn't already have it.
As an example (I've never used this - I'm not specifically recommending this brand):
https://www.amazon.com/ISC-Racers-Tape-HT2128-Transparent/dp/B000TPC7HU?ref_=fsclp_pl_dp_3
Also, to add to what jacobcanflyy says, if you don't want to go for bondage tape, a good alternative is the PTFE, which is teflon tape, or plumbers tape. you can get it for insanely cheap at any hardware store.
pic reference. Don't get it from amazon though, they stiff you on the shipping.
Looks like standard apartment wall. Washi tape should be fine (as long as you don't keep it up for like... a year or something). You can also try these removable double-sided tape
3M VHB tape. This stuff will stick to anything and will go down to sub zero temps. Make sure everything is dry when applying and prep all the surfaces that the VHB tape sticks to with 3M 94 tape primer.
​
https://www.amazon.com/3M-Scotch-5952-VHB-Tape/dp/B01BU7038A/ref=sr_1_4?ie=UTF8&qid=1549918879&sr=8-4&keywords=3M+VHB+tape
​
https://www.amazon.com/3M-Primer-94-02oz-Vinyl/dp/B005LDKTV6/ref=sr_1_1_sspa?ie=UTF8&qid=1549916087&sr=8-1-spons&keywords=3M+94+primer&psc=1
​
I got this - is good?
Not OP, but it looks like the same thing I use
I finally got around to fixing the cloudy lenses on my 2001 VW Passat.
http://imgur.com/a/HvVe9
I used:
A couple notes for anyone considering doing the same:
Well, I ordered 3 small traschcans, a shower curtain, two types of plungers, a toilet brush, and some plumber's tape so I can install my showerhead
3M Scotch 5952 VHB Tape: 1 in. x 15 ft. (Black) https://www.amazon.com/dp/B01BU7038A/ref=cm_sw_r_cp_apip_mI8CZO4gVAsfR
That stuff works wonders. I used 4 strips and it is up there haha.
3M RP25/GRY055 Scotch RP25 VHB Tape: 1/2" x 15 ft. https://www.amazon.com/dp/B00WX1P0GS/ref=cm_sw_r_cp_apa_i_KZmnDb1NGC7ZH
I bought this. It worked real good.
When I want to cut my flash I just put a little colored masking tape over it. Get good quality though, otherwise you may end up with the glue sticking to the camera. Basically this or this.
I had a problem with the original PS tape as well, it stuck for about 20 mins before it came off. I work in an automotive test lab and we use 3M’s VHB double sided tape for sticking instrumentation and other stuff inside and out side of cars. It sticks even inside of hot cars and outside in cold weather. This is what I use on my pop socket and leather case. Just use an alcohol wipe to clean the surfaces.
ScotchBlue Original Multi-Surface Painter’s Tape, .70 inch x 60 yard, 2090, 1 Roll https://www.amazon.com/dp/B00004Z4BB/ref=cm_sw_r_cp_apa_i_11y6CbB0P2K7S
so im looking to get into 3d Printing, and unless someone has some better option, im going with the MP Select Mini.
My question is on the other things i need. Here is the list of the things im looking to buy along with the printer:
I have a set of exacto knives and a screw bit set. Is there anything else im missing?
There are lots of different strength but any hardware store should have what you need
Ask for 3M VHB double-sided tape # 4905 or 4910 or Black 5952.
You can also get them online such as this: https://www.amazon.com/Adhesive-Double-sided-Conformable-Acrylic-Replacement/dp/B01863G5Q0/ref=sr_1_17?ie=UTF8&qid=1479457639&sr=8-17-spons&keywords=3M+VHB+tape+squares&psc=1
It's on Amazon for 11 bucks. It's 2.83" x 60 yards.
https://www.amazon.com/ScotchBlue-Painters-Multi-Use-2-83-Inch-60-Yard/dp/B001EJMS4M/ref=sr_1_1?ie=UTF8&qid=1484372268&sr=8-1&keywords=wide+painters+tape
Amazon, most hardware or automotive stores would have some variant. It goes by a bunch of different names. This is one example:
https://www.amazon.com/gp/product/B000TPC7HU/
Just finished taping up my new bike about 2 hours ago.
https://www.amazon.com/gp/product/B000TPC7HU/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Used that stuff. Never really bothered before other than the chain stay to protect it from chain slap but new bike is carbon and pricey. It went on easy using the soapy water method. Only real issue I have is it is glossy and the frame is matte so it is fairly obvious. I also used some 3m 2228 mastic tape in areas it would be a pita to use the other stuff and more likely to take heavy hits.
Look for 3M Scotch 5952 VHB Tape: 1 in. x 15 ft. (Black) https://www.amazon.com/dp/B01BU7038A/ref=cm_sw_r_cp_apa_i_CgH3CbR1PN0F6
Its exactly what you want.
you can use helicopter tape/racers tape to prevent that.
It appears to be painter's tape which doesn't leave a residue.
This is the same tape but you get twice as much material for $2 more
https://www.amazon.com/ScotchBlue-Painters-Multi-Use-70-Inch-60-Yard/dp/B00004Z4BB
http://www.amazon.com/3M-Vinyl-Tape-471-PN6404/dp/B005EB72WY
here ya go
Try the name brand. It worked for me
https://www.amazon.com/gp/product/B00004Z4DU/ref=oh_aui_detailpage_o01_s01?ie=UTF8&psc=1
It is 3M double sided mounting tape. Specifically, either this: Scotch Extreme Mounting Tape, 1-inch X 400-inches, Black, 1-Roll (414-LONGDC) - 414-LONG/DC https://www.amazon.com/dp/B00FUEN2GK/ref=cm_sw_r_cp_apa_i_SDlGDbQE76Q91
Or
3M Scotch 5952 VHB Tape: 1 in. x 15 ft. (Black) https://www.amazon.com/dp/B01BU7038A/ref=cm_sw_r_cp_apa_i_qElGDbGTXMETR
i bought these: https://www.amazon.com/gp/product/B01863G5Q0
FTFY:
It is 3M double sided mounting tape. Specifically, either this: Scotch Extreme Mounting Tape, 1-inch X 400-inches, Black, 1-Roll (414-LONGDC) - 414-LONG/DC https://www.amazon.com/dp/B00FUEN2GK/ref=cm_sw_r_cp_apa_i_SDlGDbQE76Q91
Or
3M Scotch 5952 VHB Tape: 1 in. x 4.6 meters. (Black) https://www.amazon.com/dp/B01BU7038A/ref=cm_sw_r_cp_apa_i_qElGDbGTXMETR
_____
^(I'm a bot) ^| ^Feedback ^| ^Stats ^| ^Opt-out ^| ^(v5.0)
If you use 3M's VHB tape, it has an rating for 90° C during use. It's the same tape used for putting up some road signs. It's also the same adhesive use on the Dual Lock Reclosable Fastener (Heavy Duty Velcro) to attach electronic toll collection tags to car windshields.
This is the stuff I use:
http://www.amazon.com/ISC-Racerstape-com-Paint-surface-guard/dp/B000TPC7HU?
You can find the black Mazda badges here and here.
Put some of this around your pots
https://www.amazon.com/dp/B01IQ8KNYK/ref=cm_sw_r_cp_apa_i_6og7CbBEBJKPH
Tape that small.
http://www.amazon.com/Ampro-A1441-PTFE-2-Inch-260-Inch/dp/B003YL4CJC/ref=sr_1_1?ie=UTF8&qid=1341637802&sr=8-1&keywords=ptfe+tape
Search for "3M VHB Black". You can get a roll and cut it to size.
Example https://www.amazon.com/3M-Scotch-5952-VHB-Tape/dp/B01BU7038A/
This is more than you'd need, but its general purpose adhesive that will come in handy for other purposes. This is the same adhesive used on gopros mounts.
If you don't wanna spend so much, get this and trim it a bit. https://www.amazon.com/Adhesive-Pads-Gopro-Helmet-Mount/dp/B00EFTP2YQ/
3m VHB 5952 is what you want
Unfortunately everything I find comes on rolls with far more than I know what to do with. On the plus side you shouldn't run out any time soon.
I used this to mount my CF spoiler on my vehicle. Outdoors in hot/cold weather, 120+MPH speeds. This shit sticks.
https://www.amazon.com/3M-Scotch-RP25-VHB-Tape/dp/B00WX1P0GS/ref=sr_1_2?ie=UTF8&qid=1469217575&sr=8-2&keywords=vhb+tape
Actually all I ever used is this:
3M ScotchBlue 2090-2A Ruban Adhésif de Masquage Peinture 48mm x 55 m https://www.amazon.fr/dp/B00004Z4DU/ref=cm_sw_r_cp_api_i_YA8YDbX87P7MH
It’s cheaper, durable, you can do whatever masking with it and cut it to shapes, never had any issue whatsoever with deteriorating paint underneath.
https://i.imgur.com/CT68Clh.jpg
Also i don’t have to bother maintaining stock of vmultiple rolls of varying width. Give it a try you won’t be disappointed
>duct-tape or similar items at the hardware store.
No! It'll DESTROY the surface. Use this stuff